™
™
PureAV
ISOLATOR
Home Theater Surge Protector
User Manual
CLEARER PICTURE
CLEANER SOUND
F9G1033-12
INSTALLATION OF THE PUREAV ISOLATOR
1) Turn OFF all of your electronic equipment and ensure that the PureAV is also
switched OFF.
2) Plug your electronic devices into the PureAV’s AC outlets.
Note: DO NOT USE two-wire extension cords or adapters with this product.
Using any extension cord in conjunction with the Belkin PureAV will void all
Belkin Components warranties. All connected equipment should be plugged
directly into your Belkin PureAV.
3) Satellite Components: Connect the coaxial cable line from the satellite source
to the PureAV’s satellite connector marked “IN”. Use a second coaxial cable to
connect the PureAV’s cable connector marked “OUT” to the appropriate input
on your satellite device.
4) Coaxial/ Antenna: Connect the coaxial cable line from the cable/ antenna source
to the PureAV’s cable/ antenna connector marked “IN”. Use a second coaxial
cable to connect the PureAV’s cable/ antenna marked “OUT” to the appropriate
input on your cable or antenna device.
5) Phone/ Fax/ Modem Data Connections: Connect a modular phone cord from the
wall jack to the PureAV’s phone jack marked “IN”. Use a second modular phone
cord to connect to the phone line jack marked “IN” on the phone to the
PureAV’s phone jack marked “OUT”.
[Each PureAV model comes with solid-state, phone/ fax/ modem, Internet-ready
(RJ11 jack) surge protection with a built-in phone line splitter.]
If desired, use a third modular phone cord and connect your computer modem
data line jack marked “IN” with the PureAV’s other phone jack marked “OUT”.
Or you can connect a second data line device of your choice (fax, etc.).
Note: If you fail to connect the phone/ fax/ modem protection, the Connected
Equipment Warranty will not cover your connected equipment with telecom
ports. Most modem damage can be prevented if you take the time to connect
the phone/ fax/ modem protection.
6) Your Belkin PureAV should be plugged into a grounded wall outlet
(3-conductor, 120V AC/ 60Hz) only.
2
FEATURES
The PureAV comes with three Diagnostic Indicators, plus an Amber Master
Switch light. When you plug the unit into a live, 120V AC/ 60Hz outlet, these
lights let you know that protection is activated and warn of a power problem
before you connect your equipment.
Protection (Yellow) indicates your surge protection is
functioning properly.
Line OK (Green) indicates line integrity.
Line Fault (Red) indicates wall outlet in use has existing
ground fault, or is improperly wired.
Protection (Yellow): This light should come on when the unit’s power
switch is turned to the “ON” position. If this light goes out at any time,
it means that your surge protector has “sacrificed itself” to protect your
equipment and should be replaced. Please contact Belkin Components for
a free surge protector replacement.
Line OK (Green): This light should also come on when the power switch is turned
on. It shows that 120V AC power is present with no wiring faults and it is safe to
plug and use connected equipment.
Line Fault (Red): If on, this light indicates that a wiring fault has been detected.
This may be the result of a lack of grounding or reversed phases, among other
problems. A qualified electrician should be notified so that the problem can be
corrected before plugging in devices.
Master (Amber): This on/ off switch provides a built-in, automatic shutdown,
15-Amp circuit breaker. The light should come on when the unit is plugged into a
120V AC/ 60Hz outlet and switched to the “ON” position. Important: If the current
draw exceeds 15 Amps for an elongated period of time, the circuit breaker will
shut down surge protector power to prevent damage. Allow a brief time for the
PureAV to cool before resetting the circuit breaker switch. (To reset, simply press
the switch.)
Power Filter Technology (PFT): As mentioned earlier, this design prevents devices
that are plugged into a given receptacle bank from transferring contamination to
a device plugged into another receptacle bank. Each pair of receptacle banks is
isolated from the other pairs within the PureAV. (The 10-outlet PureAV has five
pairs of PFT receptacle banks.)
The PureAV Isolator provides increasing levels of protection and filtration from
surges, spikes, lightning strikes, and EMI/ RFI. When AC power travels from the
wall outlet and throughout each successive pair of receptacle banks, each power
filter or “graduating filtration” level increases the isolation, filtration, and
3
FEATURES
protection for your most sensitive devices. The higher receptacle banks or “LEVELS
2,3,4,5” will provide a greater amount of surge and line-noise protection than the
first receptacle bank or “LEVEL 1”.
Note: LEVEL 1 is capable of protecting any sensitive electronic device, but you
may wish to use it for smaller, lower-draw appliances. Simply choose what devices
you desire to use and plug into the protection you need.
Cord Management: The power cord wraps around the surge unit and snaps into
the grooves along the sides for clutter-free cord management.
Wall Mounting: The PureAV is mountable using a No. 8-type screw size. Simply
measure and align the keyhole slots on the bottom of the unit over the No. 8
screws and push into place. (Screws are not included.)
BELKIN CONNECTED EQUIPMENT WARRANTY
Belkin Components warrants to the original purchaser of any Belkin Surge Protector for
the life of the product, that the surge protector shall be free of defects in design,
assembly, material, or workmanship, and will repair or replace, at its option, any
defective product free of charge.
Belkin Components will repair or replace, at its option, any equipment that is
damaged by a transient voltage surge/spike or lightning strike, (an “Occurrence”),
while properly connected through a Belkin Surge Protector to a properly wired AC
power line with protective ground. (For model F9G1033-12, the telephone line and
the coaxial cable line must be properly connected and installed, as determined by
Belkin at its sole discretion.)
Important: If you are using an AC surge protector only that does not have phone,
network, or coaxial protection, the warranty is null and void if a power disturbance
damages your equipment through the phone, network, or coaxial lines. You are only
covered if the disturbance entered through the AC lines.
This Connected Equipment Warranty is a Limited Warranty, subject to the limitations
and exclusions set forth herein. Belkin Components will spend, to repair or replace the
damaged connected equipment, at Belkin’s option, an amount equal to the fair market
value of the damaged equipment or the original purchase price of the equipment,
whichever is less, up to the maximum amount set forth below:
All models in the PureAV Isolator F9G series offer: $Unlimited Connected
Equipment Warranty.
4
BELKIN CONNECTED EQUIPMENT WARRANTY
The fair market value of the equipment shall be the current value of the equipment
specified in the most recent edition of the Orion Blue Book by Orion Research
Corporation, Roger Rohrs Publisher.
Belkin Components reserves the right to review the damaged Belkin Surge Protector, the
damaged equipment, and the site where the damage occurred. All costs of shipping the
Belkin Surge Protector and the damaged equipment to Belkin Components for
inspection shall be borne solely by the purchaser. Belkin reserves the right to negotiate
the cost of repairs. If Belkin determines, in its sole discretion, that it is impractical to
ship the damaged equipment to Belkin Components, Belkin may designate, in its sole
discretion, an equipment repair facility to inspect and estimate the cost to repair such
equipment. The cost, if any, of shipping the equipment to and from such repair facility
and of such estimate shall be borne solely by the purchaser. Damaged equipment must
remain available for inspection until the claim is finalized. Whenever claims are settled,
Belkin Components reserves the right to be subrogated under any existing insurance
policies the claimant may have.
*All above warranties are null and void if: the Belkin Surge Protector in use during the
occurrence is not provided to Belkin Components for inspection upon Belkin’s request at
the sole expense of the purchaser, Belkin Components determines that the Belkin Surge
Protector has been improperly installed, altered in any way or tampered with, Belkin
Components determines that the damage did not result from the occurrence or that no
occurrence in fact took place, the repair or replacement of the damaged equipment is
covered under a manufacturer’s warranty, or Belkin Components determines that the
connected equipment was not used under normal operating conditions or in accordance
with any labels or instructions. All Belkin Surge Protectors must be plugged directly
into the power source and must not be “daisy-chained” together in serial fashion with
other power strips, UPSes, other surge protectors or extension cords. A three- to
two-prong adapter may not be used. Any such installation voids the warranty. The
Belkin Connected Equipment Warranty only protects against damage to properly
connected equipment where Belkin Components has determined, in its sole discretion,
that the damage resulted from an occurrence, and does not protect against acts of
nature (other than lightning) such as flood, earthquake, war, vandalism, theft,
normal-use wear and tear, erosion, depletion, obsolescence, abuse, damage due to low
voltage disturbances (i.e. brownouts or sags), non-authorized program, or system
equipment modification or alteration. If you are using an AC surge protector only that
does not have phone, network, or coaxial protection, the warranty is null and void if a
power disturbance damages your equipment through the phone, network, or coaxial
lines. You are only covered if the disturbance entered through the AC lines. *Please
note: This product is not for use with aquariums and all other water-related products.
Use only indoors and in dry locations.
5
BELKIN CONNECTED EQUIPMENT WARRANTY
This warranty contains the sole warranty of Belkin Components, there are no other
warranties, expressed or, except as required by law, implied, including the implied
warranty or condition of quality, merchantability or fitness for a particular purpose,
and such implied warranties, if any, are limited in duration to the term of this warranty.
Some states do not allow limitations on how long an implied warranty lasts, so the
above limitations may not apply to you.
In no event shall Belkin Components be liable for incidental, special, direct, indirect,
consequential or multiple damages such as, but not limited to, lost business or profits
arising out of the sale or use of any Belkin Surge Protector, even if advised of the
possibility of such damages. This warranty gives you specific legal rights, and you may
also have other rights, which may vary from state to state. Some states do not allow the
exclusion or limitation of incidental or consequential damage, so the above limitations
may not apply to you.
This warranty is valid only for the original purchaser of the product. All damage claims
against the product must be made within 15 days from the date of the occurrence and
must be accompanied by a receipt for the damaged equipment or the warranty is void.
Warranty is valid in USA, Canada, Puerto Rico, and Bermuda.
To file a claim against the Belkin Connected Equipment Warranty, you must take the
following steps: Contact Belkin online at www.belkin.com and print our claim form or
write to us at Belkin Components, 501 W. Walnut St., Compton CA 90220 Attn: Technical
Support, or call 310-898-1100, extension 2263, within 15 days of the occurrence. Be
prepared to provide the following information:
A. The part number of the Belkin Surge Protector.
B. The equipment that was connected to the Surge Protector at the time
of the occurrence.
C. The equipment that was damaged during the occurrence and the extent of the damage.
D. The date of the occurrence.
E. Where you purchased the Surge Protector.
F. When you purchased the Surge Protector.
G. Copy of original receipt.
Your Belkin Customer Service Representative will then instruct you on how to forward your
equipment, receipt, Belkin Surge Protector in use during the “occurrence” and how to proceed
with your claim.
You may conveniently register your Belkin PureAV Isolator surge protector online on our website
www.belkin.com, or fill out and send in the registration card included with your PureAV purchase.
6
belkin.com
Belkin Components
501 West Walnut Street
Compton • CA • 90220 • USA
Tel: 310.898.1100
Fax: 310.898.1111
Belkin Components, Ltd.
Express Business Park
Shipton Way • Rushden • NN10 6GL • United Kingdom
Tel: +44 (0) 1933 35 2000
Fax: +44 (0) 1933 31 2000
Belkin Components B.V.
Starparc Building • Boeing Avenue 333
1119 PH Schiphol-Rijk • The Netherlands
Tel: +31 (0) 20 654 7300
Fax: +31 (0) 20 654 7349
Belkin Components, Ltd.
7 Bowen Crescent • West Gosford
NSW 2250 • Australia
Tel: +61 (0) 4372 8600
Fax: +61 (0) 4372 8603
P73999
© 2002 Belkin Components. All rights reserved. All trade names are
registered trademarks of respective manufacturers listed.
|