Earn BISSELL Rewards!
Register your
product today!
See details on
back page
USER'S GUIDE
53Y8, 29H3, 75Q3 SERIES
2
3
Thank You
Safety Instructions
Product View
4
5
Assembly
5-6
Operations
6-8
9-10
10
Maintenance and Care
Troubleshooting
Replacement Parts
11
12
12
Warranty
Product Registration
Consumer Services
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic
precautions should be observed, including
the following:
■ Keep hair, loose clothing, fingers, and all
parts of body away from openings and
moving parts.
■ Use extra care when cleaning stairs.
Read all
■ Do not pick up flammable materials
(lighter fluid, gasoline, kerosene, etc.) or
use in the presence of explosive liquids
or vapors.
■ Always turn off this appliance before con-
necting or disconnecting the motorized
nozzle.
instRuctions
befoRe using youR
VacuuM.
WaRning: to
reduce the risk of fire,
■ Do not pick up toxic material (chlorine
electric shock, or injury:
bleach, ammonia, drain cleaner, etc.).
■ Do not use outdoors or on wet surfaces.
■ Do not use vacuum cleaner in an
enclosed space filled with vapors given
off by oil base paint, paint thinner, some
moth proofing substances,
■ Do not allow to be used as a toy.
■ Close attention is necessary when used
by or near children.
■ Do not use for any purpose other than
described in this User’s Guide.
■ Use only manufacturer’s recommended
attachments.
flammable dust, or other explosive or
toxic vapors.
■ Do not pick up hard or sharp objects
such as glass, nails, screws, coins, etc.
■ Do not pick up anything that is burning
or smoking, such as cigarettes, matches, or
hot ashes.
■ Do not use with damaged cord or plug.
■ If appliance is not working as it should,
has been dropped, damaged, left out-
doors, or dropped into water, have it
repaired at an authorized service center.
■ Do not pull or carry by cord, use cord as a
handle, close a door on cord, or pull cord
around sharp edges or corners. Do not
run appliance over cord. Keep cord away
from heated surfaces.
■ Do not unplug by pulling on cord. To
unplug, grasp the plug, not the cord.
■ Do not handle charger, including charger
plug and charger terminal with wet hands.
■ Do not use without dust cup or filters in
place.
■ Use only on dry, indoor surfaces.
■ Keep appliance on a level surface.
saVe tHese
instRuctions
foR futuRe use
This model is for household use only.
■ Do not charge the unit outdoors.
■ Use only the charger supplied by the
manufacturer to recharge.
■ Do not incinerate the appliance even if
it severely damaged. The batteries can
explode in a fire.
■ Do not put any object into opening.
■ Do not use with any opening blocked.
■ Keep openings free of dust, lint, hair and
anything that may reduce airflow.
3
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Product view
Power/Brush roll
On/Off
2-Way Folding
Handle Release
Hand Vacuum
Release
Dirt Cup Release
Detachable
Hand
Vacuum
Filter
Dirt Container
Charging Adapter Plug
Integrated
Crevice Tool
caution:
Swivel Head
Do not plug in your vacuum
cleaner until you are famil-
iar with all instructions and
operating procedures.
4
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Assembly
no tools are required for assembly;
simply insert foot into body of unit until
you hear a click.
charging
before charging, make sure unit is in
the off position.
1. Insert the charging adapter plug into the
charging port on the back of the unit.
2. Plug the adapter into the wall outlet. The red
indicator light will illuminate and remain on
when plugged into wall outlet. Charge the
unit completely for 24 hours prior to first use.
1.
note: the adapter may become warm
during charging – this is normal.
3. When the unit is fully discharged, approx-
imately 16 hours of charging is required
for the battery to regain full capacity.
Operations
Power switch
the power switch is located on the top of
the handle. settings include:
(o) = off
(i) = suction on
(bRusH) = suction and brush on
using your stick vacuum
1. Push power switch on to desired setting.
2. Easily clean hard floors, low pile carpet,
and area rugs.
3. When finished cleaning, turn power
switch to OFF (O) position.
2-way folding handle
for cleaning under couches, beds and
other hard to reach areas.
1.
2-Way Folding
Handle Release
1. To release, push button located under
power switch to bend handle forward for
cleaning under furniture.
2. For space saving storage, push button to
bend handle backward.
5
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Operations
cleaning with the detachable hand vac
1. Remove hand vac by pressing the release
button.
1
2. Power switch is located under handle and
should be depressed while cleaning is tak-
ing place.
Power Switch
3. Easily clean messes on furniture, stairs,
and other hard to reach areas.
4.
5.
4. For hard to reach messes, use the
integrated crevice tool. To access crevice
tool, pull on tab indicated by arrow on
front of hand vac nozzle. Listen for click to
know crevice tool is ready to use.
5. When done cleaning, simply push crevice
tool back into unit.
Maintenance and care
to maintain maximum cleaning perfor-
mance, the following maintenance steps
must be performed:
emptying the dirt cup
dirt cup should be emptied before
debris reaches the full line on cup.
1. Turn power OFF (O) and remove hand
2.
3.
vacuum from unit, as directed in step 1
"Cleaning with the detachable hand vac".
2. Hold hand vacuum vertically and depress
the release button to release dirt container.
3. Gently pull dirt container away from the
hand vacuum grip and remove the filter.
Empty dirt into waste container.
4. Replace filter back into the dirt container
and attach dirt container to hand vacuum
until it snaps securely in place.
cleaning or Replacing the filter
the key to maximum performance is
having a clean filter. cleaning the filter
after each use will help your vacuum
operate at peak efficiency.
6
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Maintenance and care
cleaning or Replacing the filter continued
use only genuine bissell replace-
ment filters in your bissell vacuum.
to purchase visit WWW.bissell.coM
or call 1-800-237-7691.
To clean filter:
1. Turn power OFF (O).
2. Remove the dirt container from the hand
vacuum, as directed in step 1 "Emptying
the dirt cup" on page 6.
3. Remove filter and tap firmly against the
3.
4.
inside of a waste container, removing
any visible dirt.
4. Replace filter back into the dirt container
and attach dirt container to hand
vacuum until it snaps securely in place.
NOTE: After heavy usage, you may
clean the filter by washing it gently
by hand in warm water and mild
dish detergent. Rinse thoroughly
and make certain it is completely
dry before replacing it.
brush roll and brush roll belt maintenance
the brush roll may accumulate debris
such as strings, hair and fibers. this
type of debris can wrap around the
brush and diminish its ability to clean
effectively.
To remove brush roll for cleaning:
1. Turn power OFF (O). Remove foot
2.
assembly from unit and turn over to
access the brush roll.
2. Remove three Phillips head screws to
remove the belt cover.
3. To remove brush roll, pull on the brush
near the belt side. Clean off hair or
other debris from brush roll.
4. Place cleaned brush roll back into foot
of unit by aligning the non-belt side so
it's seated in the nozzle.
3
5. Pivot the brush roll so the belt end slides
into the slot in the nozzle.
6. Replace the belt cover and secure with
three screws. Attach foot assembly
on unit.
7
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Maintenance and care
brush roll and brush roll belt maintenance continued
Brush roll reset:
if larger debris becomes lodged in the
foot of the unit and the brush roll shuts
off, turn the unit off and remove the
obstruction. Wait approximately 15 sec-
onds for the motor to cool down before
turning back on. brush will function
again after allowing time to cool down.
Brush roll belt replacement:
if the brush roll belt should break,
call 1-800-237-7691 or visit WWW.
bissell.coM to purchase replacement
belt.
Replacement instructions:
1. Turn power OFF (O). Remove foot
assembly from unit and turn over to access
the brush roll belt.
2.
3
2. Remove three Phillips head screws to
remove the belt cover.
3. Locate broken belt.
4. Replace belt.
5. Place brush roll back into foot of unit.
6. Replace the belt cover and secure with
three screws.
7. Attach foot assembly on unit.
disposal of batteries
WaRning:
This product contains Nickel Metal Hydride (NiMH)
rechargeable batteries. According to Federal and State
regulations, removal and proper disposal of NiMH bat-
teries is required. For removal of the batteries in your
Lift-Off Floor & More see instructions below.
TM
if your lift-off floors & More is to be
disposed of, the batteries should be
removed and disposed of properly.
3.
1. iMPoRtant: Unplug Charger.
2. Remove hand vac from unit and remove
dirt cup from handle.
3. Remove (5) Phillips head screws on the
5 screws
handle and cover.
8
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Maintenance and care
disposal of batteries continued
4. Separate left and right cover.
5. Remove the entire battery assembly from
the cover.
6. Remove (3) Phillips head screws between
the motor and battery bracket.
7. Pull the motor, PCB, fuse, and inner wire
through the middle of the battery bracket,
separating the battery bracket and single
battery from the motor, PCB, and inner wire.
8. Cut wires from the PCB and fuse to the
battery bracket.
9. Keep Battery Pack together – DO NOT
separate individual batteries. For specific
disposal instructions of batteries, please
contact RBRC (Rechargeable Battery
Recycling Corporation) 1-800-822-8837
or visit www.rbrc.com.
10.Discard remainder of product
caution: Disconnecting the battery will
destroy the appliance and void the war-
ranty.
Troubleshooting
Vacuum won’t turn on
Possible causes
Remedies
1. Battery isn’t fully charged
1. Charge battery. Follow charging battery instructions on page 5
brush roll not turning
Possible causes
Remedies
1. Brush roll is jammed
2. Brush roll needs to be reset
3. Broken brush roll belt
1. Remove obstruction. Follow instructions on pages 7 and 8
2. Follow instructions on page 8
3. Follow instructions on page 8
Vacuum cleaner has low suction
Possible causes
Remedies
1. Dirt container is full
1. Empty dirt container
2. Dirt container is not installed properly
3. Foot is loose
2. Position container correctly and snap firmly into place
3. Make sure foot is fully inserted into body of unit
4. Follow filter instructions on page 7
4. Filters need cleaning
5. Filters need replacing
replacement filters.
9
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Troubleshooting
Visible dirt escaping from vacuum
Possible causes
Remedies
1. Dirt container is full of debris
1. Empty dirt container
2. Filter is missing or installed incorrectly
3. Dirt container installed incorrectly
2. Check filter for correct installation
3. Position container correctly and snap firmly into place
other maintenance or service not included in the manual should be
performed by an authorized service representative.
thank you for selecting a bissell product.
Please do not return this product to the store.
for any questions or concerns, bissell is happy to be of
service. contact us directly at 1-800-237-7691.
Replacement parts - BISSELL vacuum
you may purchase parts by calling bissell consumer services or by
visiting our website. below is a list of common replacement parts.
Item
Part No.
Part Name
1
52H6
Filter assembly – set of 2
2
3
4
5
6
7
203-1612
203-1609
203-1610
203-1607
203-1608
203-1611
Charging adapter plug
Foot assembly
Dirt cup assembly
Brush roll belt
Brush roll
Hand vac assembly
1
2
3
7
4
5
6
10
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Warranty - BISSELL Lift-Off Floors & More Stick Vacuum
This warranty gives you specific legal rights, and you may also have other rights which may
vary from state to state. If you need additional instruction regarding this warranty or have
questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail,
telephone, or regular mail as described below.
limited one year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product
BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or
products), at BISSELL’s option, free of charge from the date of purchase by the original
purchaser, for one year any defective or malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This
warranty does not apply to fans or routine maintenance components such as filters, belts, or
brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any
other use not in accordance with the User's Guide is not covered.
if your bissell product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your
area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Services.
Website or e-mail:
Use the “Customer Support” tab.
or call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
or Write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids, MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
*eXcePtions and eXclusions fRoM tHe teRMs of tHe liMited WaRRanty
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR
WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED
ABOVE.
Some states do not allow limitations on how long an implied warranty last so the
above limitation may not apply to you.
11
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
Don't forget to register your product!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:
bissell Rewards Points
Automatically earn points for discounts and free shipping on future purchases.
faster service
Supplying your information now saves you time should you need to contact us with
questions regarding your product.
Product support Reminders and alerts
We’ll contact you with any important product maintenance reminders and alerts.
special Promotions
Optional: Register your email to receive notice of offers, contests, cleaning tips and more!
Visit www.bissell.com/registration now!
BISSELL consumer services
For information about repairs or replacement parts, or questions about your warranty, call:
bissell consumer services
1-800-237-7691
Monday - Friday 8 a.m. — 10 p.m. ET
Saturday
9 a.m. — 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of cleaner available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
note: Please keep your original sales receipt. it
provides proof of purchase date in the event of a
©2011 BISSELL Homecare, Inc
warranty claim. see Warranty on page 11 for details.
Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 110-4369
Rev 04/11
Visit our website at:
12
w w w . b i s s e l l . c o m
8 0 0 . 2 3 7 . 7 6 9 1
|