Black Box Network Hardware Hardened VDSL Ethernet Extender User Manual

May, 2008  
Hardened VDSL Ethernet Extender  
LB303A  
Order toll-free in the U.S. Call : 877-877-BBOX ( Outside U. S. call 724-746-5500 )  
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax  
724-746-0746  
CUSTOMER  
SUPPORT  
INFORMATION  
Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018  
 
Hardened VDSL Ethernet Extender  
8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá a lo  
descrito en las instrucciones de operación. Todo otro servicio deberá ser referido a  
personal de servicio calificado.  
9. El aparato eléctrico debe ser situado de tal manera que su posición no interfiera su uso. La  
colocación del aparato eléctrico sobre una cama, sofá, alfombra o superficie similar puede  
bloquea la ventilación, no se debe colocar en libreros o gabinetes que impidan el flujo de  
aire por los orificios de ventilación.  
10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor como  
radiadores, registros de calor, estufas u otros aparatos (incluyendo amplificadores) que  
producen calor.  
11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del tipo descrito en  
el instructivo de operación, o como se indique en el aparato.  
12. Precaución debe ser tomada de tal manera que la tierra fisica y la polarización del equipo  
no sea eliminada.  
13. Los cables de la fuente de poder deben ser guiados de tal manera que no sean pisados ni  
pellizcados por objetos colocados sobre o contra ellos, poniendo particular atención a los  
contactos y receptáculos donde salen del aparato.  
14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las recomendaciones del  
fabricante.  
15. En caso de existir, una antena externa deberá ser localizada lejos de las lineas de energia.  
16. El cable de corriente deberá ser desconectado del cuando el equipo no sea usado por un  
largo periodo de tiempo.  
17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre  
la cubierta u orificios de ventilación.  
18. Servicio por personal calificado deberá ser provisto cuando:  
A: El cable de poder o el contacto ha sido dañado; u  
B: Objectos han caído o líquido ha sido derramado dentro del aparato; o  
C: El aparato ha sido expuesto a la lluvia; o  
D: El aparato parece no operar normalmente o muestra un cambio en su desempeño; o  
E: El aparato ha sido tirado o su cubierta ha sido dañada.  
3
 
Hardened VDSL Ethernet Extender  
Preface  
This manual describes how to install and use the Hardened VDSL Ethernet Extender.  
The Hardened VDSL Ethernet Extender introduced here provides one channel for  
Ethernet over VDSL.  
The Hardened VDSL Ethernet Extender fully complies with IEEE802.3 10Base-T and  
IEEE802.3u 100Base-TX/FX standards.  
In this manual, you will find:  
y Product overview  
y FEATURES ON THE HARDENED VDSL ETHERNET EXTENDER  
y Illustrative LED functions  
y Installation instructions  
y Specifications  
4
 
 
Hardened VDSL Ethernet Extender  
Introduction  
The Hardened VDSL Ethernet Extender provides one channel for Ethernet over VDSL.  
This Hardened VDSL Ethernet Extender solution is perfectly fitted in the industrial  
applications or rugged environment.  
Product Overview  
Product Features  
y Meets NEMA TS1/TS2 Environmental requirements such as temperature, shock,  
and vibration for traffic control equipment  
y
y
y
Meets IEC61000-6-2 EMC Generic Standard Immunity for industrial environment  
Operates transparent to higher layer protocols such as TCP/IP  
Ethernet Port: Supports IEEE802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps,  
full/half-duplex; Auto MDI/MDIX  
y
VDSL port: Symmetrical on the VDSL, high-speed full-duplex 50Mbps  
communications link over existing copper telephone line  
y
y
One DIP switch for configuring Local (Loc) and Remote (Rmt)  
Ten speeds with speed indicator LEDs on front panel of unit, up to 50Mbps @  
about 300meters (984ft.), down to 1Mbps @ about 1,900meters (6,233ft.)  
Operating voltage and Max. current consumption: 0.225A @ 12VDC, 0.113A @  
24VDC. Power consumption: 2.7W Max.  
y
y
Power Supply: Redundant 12-30VDC Terminal Block power inputs and 12VDC  
DC JACK with 100-240VAC external power supply  
y
y
Operating temperature ranges from -34 to 74  
Supports Din-Rail, Panel, or Rack Mounting installation  
Packing List  
When you unpack this product package, you will find the items listed below. Please  
inspect the contents, and report any apparent damage or missing items immediately to  
our authorized reseller.  
6
 
 
Hardened VDSL Ethernet Extender  
The Hardened VDSL Ethernet Extender  
USERS MANUAL  
AC to DC Power Adaptor and Power Cable (optional)  
7
 
Hardened VDSL Ethernet Extender  
One-Channel Hardened VDSL Ethernet Extender  
Ports  
The Hardened VDSL Ethernet Extender provides one TX port and one VDSL port.  
For the TX port, it uses RJ-45 connector and auto senses the speed of 10/100Mbps.  
For the VDSL port, it uses RJ-11 and Terminal Block connectors and auto senses the  
speed of 1/3/5/10/15/20/25/30/40/50Mbps.  
VDSL Mode Settings  
VDSL mode settings are made very simple by means of a DIP (Dual Inline Package)  
switch on the top panel of the Hardened VDSL Ethernet Extender.  
DIP switch  
There is one pin on the DIP switch for VDSL mode settings. Refer to the table below  
for more details.  
Loc  
Rmt  
The device operates in local  
mode  
The device operates in remote  
mode  
8
 
 
Hardened VDSL Ethernet Extender  
Front Panel & LEDs  
LED Indicators  
The LED indicators give you instant feedback on status of the Hardened VDSL  
Ethernet Extender:  
LEDs  
State  
Indication  
Power on  
Power1  
Steady  
Power2  
Power3  
Ethernet  
Off  
Power off  
Steady  
A valid Ethernet connection established  
Transmitting or receiving Ethernet data  
ACT stands for ACTIVITY  
Flashing  
Link/ACT  
FDX  
Neither valid Ethernet connection established nor  
transmitting/receiving Ethernet data  
Off  
Ethernet Connection in full-duplex mode  
FDX stands for FULL-DUPLEX  
Steady  
Off  
Ethernet Connection in half-duplex mode  
Ethernet over VDSL  
Green  
The VDSL port transmitting/receiving at 1Mbps, up to 1900M  
The VDSL port transmitting/receiving at 3Mbps, up to 1800M  
The VDSL port transmitting/receiving at 5Mbps, up to 1600M  
The VDSL port transmitting/receiving at 10Mbps, up to 1400M  
The VDSL port transmitting/receiving at 15Mbps, up to 1200M  
The VDSL port transmitting/receiving at 20Mbps, up to 1000M  
The VDSL port transmitting/receiving at 25Mbps, up to 800M  
The VDSL port transmitting/receiving at 30Mbps, up to 700M  
The VDSL port transmitting/receiving at 40Mbps, up to 600M  
The VDSL port transmitting/receiving at 50Mbps, up to 300M  
The device operates in remote mode  
1
Amber  
Green  
2
Amber  
Green  
3
Amber  
Green  
4
Amber  
Green  
5
Amber  
Remote  
Local  
Error  
Steady  
Steady  
Steady  
Steady  
The device operates in local mode  
Error occurred  
Link  
A valid VDSL connection established  
9
 
 
Hardened VDSL Ethernet Extender  
Installation  
This chapter gives step-by-step installation instructions for the Hardened VDSL  
Ethernet Extender.  
Selecting a Site for the Equipment  
As with any electric device, you should place the equipment where it will not be  
subjected to extreme temperatures, humidity, or electromagnetic interference.  
Specifically, the site you select should meet the following requirements:  
The ambient temperature should be between -34 to 74 degrees  
Celsius.  
The relative humidity should be less than 95 percent, non-condensing.  
Surrounding electrical devices should not exceed the electromagnetic  
field (RFC) standards.  
Make sure that the equipment receives adequate ventilation. Do not  
block the ventilation holes of the equipment.  
The power outlet should be within 1.8 meters of the product.  
DIN Rail Mounting  
Fix the DIN rail attachment plate to the back panel of the Hardened VDSL Ethernet  
Extender.  
Installation: Place the Hardened VDSL Ethernet Extender on the DIN rail from above  
using the slot. Push the front of the Hardened VDSL Ethernet Extender toward the  
mounting surface until it audibly snaps into place.  
Removal: Pull out the lower edge and then remove the Hardened VDSL Ethernet  
Extender from the DIN rail.  
10  
 
 
Hardened VDSL Ethernet Extender  
Connecting to Power  
Redundant DC Terminal Block Power Inputs or 12VDC DC Jack:  
12VDC DC Jack  
Step 1: Connect the supplied AC to DC power adapter to the receptacle  
on the topside of the Hardened VDSL Ethernet Extender.  
Step 2: Connect the power cord to the AC to DC power adapter and  
attach the plug into a standard AC outlet with the appropriate AC  
voltage.  
Redundant DC Terminal Block Power Inputs  
There are two pairs of power inputs can be used to power up this device. You only need  
to have one power input connected to run the Hardened VDSL Ethernet Extender.  
Step 1: Connect the DC power cord to the plug-able terminal block on  
the Hardened VDSL Ethernet Extender, and then plug it into a standard  
DC outlet.  
Step 2: Disconnect the power cord if you want to shut down the  
Hardened VDSL Ethernet Extender.  
Power Input Assignment  
Power1  
12VDC  
DC Jack  
12-30VDC  
Power Ground  
12-30VDC  
Power Ground  
Power2  
Terminal Block  
Power3  
Earth Ground  
DIP Switch Assignment  
Loc  
Rmt  
The device operates in local mode  
The device operates in remote mode  
11  
 
 
Hardened VDSL Ethernet Extender  
Specifications  
Applicable Standards  
IEEE802.3 10Base-T  
IEEE802.3u 100Base-TX  
Ethernet over VDSL  
Fixed Ports  
1 x 10/100Mbps Ethernet port with RJ-45 connector  
1 x Ethernet over VDSL port with RJ-11 and Terminal  
Block connectors  
Speed  
10Base-T  
10/20Mbps for half/full-duplex  
100/200Mbps for half/full-duplex  
100Base-TX  
Ethernet over VDSL  
1, 3, 5, 10, 15, 20, 25, 30, 40, 50Mbps  
Switching Method  
Forwarding rate  
Cable  
Store-and-Forward  
14,880/148,810pps for 10/100Mbps  
10Base-T  
100Base-TX  
2-pair UTP/STP Cat. 3, 4, 5 up to 100m  
2-pair UTP/STP Cat. 5 up to 100m  
Ethernet over VDSL Cross-over telephone wires  
LED Indicators  
Per Unit (3 LEDs)-  
Power1, Power2, Power3  
Per Port-  
RJ-45 (2 LEDs): Link/ACT, FDX  
RJ-11, Terminal Block (9 LEDs): Remote,  
Local, Error, Link, 1, 2, 3, 4, 5  
Dimensions  
50mm (W) × 110mm (D) x 136mm (H)  
(1.97” (W) x 4.33” (D) x 5.35” (H))  
Weight  
Power  
0.8Kg (1.76lbs.)  
Terminal Block: 12-30VDC  
DC Jack: 12VDC, External AC/DC required  
Operating Voltage &  
Max.  
0.225A @ 12VDC, 0.113A @ 24VDC  
Current Consumption  
Power Consumption  
Operating Temperature  
Storage Temperature  
Humidity  
2.7W Max.  
-34°C ~ 74°C (-29°F ~ 165°F)  
-40°C ~ 85°C (-40°F ~ 185°F)  
10 ~ 95%, non-condensing  
UL60950, EN60950, IEC60950  
Safety  
Emissions  
FCC Part 15, Class A  
CE: EN61000-6-2  
EN61000-6-3  
12  
 
 
Hardened VDSL Ethernet Extender  
Standards  
ESD Standard (EN61000-4-2)  
Radiated FRI Standards (EN61000-4-3)  
Burst Standards (EN61000-4-4)  
Surge Standards (EN61000-4-5)  
Induced RFI Standards (EN61000-4-6)  
Magnetic Field Standards (EN61000-4-8)  
Voltage Dips Standards (EN61000-4-11)  
Environmental Test Compliance:  
Vibration Resistance (IEC60068-2-6)  
Shock (IEC60068-2-27)  
Free Fall (IEC60068-2-32)  
NEMA TS1/2 Environmental requirements for  
traffic control equipment  
13  
 

Blaupunkt Car Stereo System RCR 127 User Manual
BodyCraft Home Gym F415 User Manual
Bose Network Card 802c User Manual
Bradley Smoker Smoker BTDS108CE EU User Manual
Canon Printer MX640 User Manual
Carrier Air Conditioner 30RB060 390 User Manual
Cary Audio Design Stereo Amplifier CAD 211 AE User Manual
Casio Digital Camera EX Z12 User Manual
Cecilware Boiler ME10 GN User Manual
Cecilware Kitchen Grill SG 1SG User Manual