FCC and IC RFI Statements
Chapter 3: Rear Panel Connections on the LPR1131
Chapter 4: Power and Extend Distance
LPR1101
LPR1131
FEDERAL COMMUNICATIONS COMMISSION
and INDUSTRY CANADA
4. Power and Extend Distance
3. Rear Panel Connections on the LPR1131
RADIO FREQUENCY INTERFERENCE STATEMENTS
The PoE extender provides automatic crossover detection, making it simple to connect to another
device without crossover cable.
Power is supplied through CAT5/5e/6 cable from the PSE and extends the distance up to 328 feet
(100 m) to the PD port of another extender.
Gigabit PoE Extender
Class B Digital Device. This equipment has been tested and found to comply with the limits for a
Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residential installation. However,
there is no guarantee that interference will not occur in a particular installation. This equipment
generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. If this
equipment does cause harmful interference to radio or telephone reception, which can be deter-
mined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one of the following measures:
Gigabit PoE Extender
(LPR1131)
Gigabit PoE Extender
(LPR1131)
Gigabit PoE
Extender
Gigabit PoE
Extender
Extend the distance and provide 48-VDC
power to Ethernet devices.
(LPR1131)
(LPR1131)
Both models have (1) PD in, and (1) PSE out port.
With LPR1131, you can also add a local 3-port switch.
PoE switch/
PoE injector
100M
100M
100M
• Reorient or relocate the receiving antenna.
Gigabit PoE
Extender
(LPR1131)
• Increase the separation between the equipment and receiver.
100M
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
PoE IP
camera
100M
• Consult an experienced radio/TV technician for help.
PC
Mac®
Server
PSE
Caution:
(PoE injector/switch)
Gigabit PoE
Extender
(LPR1131)
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Non-PoE
IP camera
PoE
splitter
To meet FCC requirements, shielded cables and power cords are required to connect this device
to a personal computer or other
Figure 3-1. Rear panel connections.
Class B certified device. This digital apparatus does not exceed the Class B limits for radio noise
emission from digital apparatus set out in the Radio Interference Regulation of Industry Canada.
Power
cable
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de classe B prescrites dans le Règlement sur le brouillage
radioélectrique publié par Industrie Canada.
100M
Figure 4-1. Typical application.
100M
© Copyright 2013. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond logo are regis-
tered trademarks of BB Technologies, Inc. Mac is a registered trademark of Apple Computer, Inc. Any third-party
trademarks appearing in this manual are acknowledged to be the property of their respective owners.
LPR1101, version 1
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S.
call 724-746-5500) FREE technical support 24 hours a day, 7 days a
week: Call 724-746-5500 or fax 724-746-0746 Mailing address:
Black Box Corporation, 1000 Park Drive, Lawrence, PA 15055-1018
Customer
Support
Information
FREE! Live, 24/7 Tech Support is just 30 seconds away.
724-746-5500
|
blackbox.com
•
E-mail: [email protected]
Page 5
Page 6
LPR1101
LPR1101
724-746-5500 | blackbox.com
Chapter 2: Overview
724-746-5500 | blackbox.com
Chapter 1: Specifications; Chapter 2: Overview
Chapter 2: Overview
Chapter 2: Overview
• IEEE 802.3af Power Sourcing Equipment (PSE) provides power to a Powered Device (PD).
• Unit is palm-sized with a metal case.
1. Specifications
5
Table 2-1. LPR1101 components.
• Auto-learns networking configurations.
Certification — FCC Class A, CE, RoHS
Number in
Figures 2-1
and 2-2
• Autodetects full-/half-duplex modes for any port.
• Provides dedicated full-duplex 2000 Mbps bandwidth.
Media Type — CAT5, 5e, 6 UTP or STP cable
Component
Description
Connectors — LPR1101: (2) RJ-45, including (1) PD and (1) PSE;
LPR1131: (5) RJ-45, including (1) PD and (1) PSE; (3) RJ-45 ports for switching
Figure 2-4. LPR1131 back panel.
Table 2-2. LPR1131 components.
• Complies with IEEE 802.3x flow control for full-duplex operation and backpressure flow control
for half-duplex operation.
1
2
(1) PoE Out LED
(1) PoE In LED
Lights to indicate PoE out on Port 1.
Lights to indicate PoE in on Port 2.
Indicators — LPR1101: (6) LEDs: (1) PoE in, (1) PoE out, (2) 1000M, (2) Link/Act;
LPR1131: (12) LEDs: Power: (1) PoE out, (1) PoE in, (5) 1000M, (5) Link/Act
• Supports Auto-MDI/MDI-X for any port.
• Unit is smart plug-and-play.
Temperature — Operating: 32 to 104º F (0 to 40º C);
Storage: -4 to 194º F (-20 to 90º C)
Number
in Figures
2-3 and 2-4 Component
Lights when data rate is 1000 Mbps.
Blinking when data rate is 100 Mbps.
Off when data rate is 10 Mbps.
2.3 What’s Included
• Gigbit PoE Extender (LPR1101 or LPR1131)
Power — Input: 48 VDC; Output: 48 VDC;
Consumption (maximum): LPR1101: 2 watts,
LPR1131: 6 watts
3
(2) 1000M LEDs
Description
• This user’s manual
1
2
(1) PoE Out LED
Lights to indicate PoE out on Port 1.
Lights to indicate PoE in on Port 5.
Size — 0.9"H x 5.1"W x 3"D (2.4 x 13 x 7.7 cm)
Weight — 0.4 lb. (0.2 kg)
2.4 Hardware Description
Figures 2-1 through 2-4 show the front and back panels of the extenders. Tables 2-1 and 2-2
describe their components.
On when port is connected.
(1) PoE In LED
4
(2) Link/Act LEDs
Off when there is no connection.
Flashing when data is transmitted or received.
2. Overview
2.1 Introduction
Lights when data rate is 1000 Mbps.
Blinking when data rate is 100 Mbps.
Off when data rate is 10 Mbps.
2.4.1 LPR1101
3
(5) 1000M LEDs
5
(2) RJ-45 connectors
Port 1: (1) output (PSE), Port 2: (1) input (PD)
1
2
3
4
3
4
The Gigabit PoE Extender (LPR1101) provides (1) 10-/100-/1000-Mbps PD input port and (1)
10-/100-/1000-Mbps PSE output port. The LPR1131 has the same ports as the LPR1101, plus it
also has a 3-port 10-/100-/1000-Mbps switch. Both extenders comply with the IEEE 802.3af
standard.
On when port is connected.
2.4.2 LPR1131
4
5
(5) Link/Act LED
Off when there is no connection.
Flashing when data is transmitted or received.
1
2
3
4
3
4
3
4
3 3
You can connect the PSE port of one extender to the PD port of another extender over up to
328 feet (100 m) of CAT5/5e/6 cable. Each hop uses 2.5 W and reduces the power available on
the PSE port by that amount.
Figure 2-1. LPR1101 front panel.
Port 1: (1) output (PSE), Port 5: (1) input (PD),
(3) Ethernet switch ports
(5) RJ-45 connectors
Depending on the power required by the PD device connected to the PSE port, the extender will
determine how many hops you can go before you do not have enough power available to power
the PD device.
5
5
4 4
2.2 Features
Figure 2-3. LPR1131 front panel.
• LPR1131 only: combines a 3-port 10-/100-/1000-Mbps switch with a 1-port PoE extender.
• LPR1101: functions as a 1-port PoE extender.
Figure 2-2. LPR1101 back panel.
• Both LPR1101 and LPR1131 have (1) PD (data + power in) port and (1) PSE (data + power out)
port.
• IEEE 802.3af Powered Device (PD) (data + power in) gets power from a Power Sourcing
Equipment (PSE).
Page 1
Page 2
Page 3
Page 4
LPR1101
LPR1101
LPR1101
LPR1101
724-746-5500 | blackbox.com
724-746-5500 | blackbox.com
724-746-5500 | blackbox.com
724-746-5500 | blackbox.com
|