SMM2-2U
Sliding Monitor Mount, 2- or 4-Post, 2U
Mount a 15", 17", or 19" monitor in a 2- or 4-Post
2U cabinet or rack.
Monitor NOT included.
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,
Customer
Support
Information
What’s Included/Installation Instructions
Rackmount hardware:
• (8) 12-24 x 1⁄2" pan-head screws
• (8) 10-32 x 1⁄2" pan-head screws
• (8) 12-24 cage nuts
• (8) 10-32 cage nuts
Rear hardware:
• (6) 8-32 x 3/8" pan-head screws
• (6) 8-32 nuts with star washers
3. Installation Instructions
Step 1: Mounting depth: Measure the mounting depth for your rack
from the front of the front-mounting surface to the back
of the back-mounting surface.
2-post with
adapter brackets
Double 2-post
4-post cabinet
Mounting depth
Mounting depth
Figure 1. Mounting depth measurements.
Step 2: If mounting in a 2-post rack, attach the 2U adapter brackets to the 2-post
rack before installing the 2U sliding monitor tray.
Step 3: 23.5" to 31.5": Install the rear rack brackets as shown in Figure 2 for this
mounting depth range (see Step 5 for assembly).
Mounting depth 23.5"–31.5"
Figure 2. Mounting depth: 23.5" to 31.5".
SMM4-2U
Page 3
724-746-5500 | blackbox.com
Installation Instructions
Step 4: 15.5" to 23.5": Install the rear rack brackets as shown in Figure 3 for this
mounting depth range (see Step 5 for assembly).
Mounting depth 15.5"–23.5"
Reversed rear
bracket
Figure 3. Mounting depth: 15.5" to 23.5".
Step 5: Rear bracket attachment.
Step 5A: Move the slide rails back approximately 10" (25.4 cm). You might need
to loosen the thumbscrews to do this.
Step 5B: Attach the rear rack brackets and the cable arm extension as shown in
Figure 4, using (4) 8-32 x 3/8" pan-head screws and (4) 8-32 nuts. Place
the screws as far apart as possible (see Figure 4).
Step 5C: Tighten all screws.
NOTE: You can attach the cable arm extension to the right or left side, based on
your cabling needs.
(1) rear bracket
(4) 8-32 x 3⁄8" screws
(gold)
(2) 8-32 nuts
(1) cable management
bracket
(1) rear bracket
(2) 8-32 nuts
Slide the outer rails back approx. 10".
Figure 4. Attaching the rear bracket.
SMM4-2U
Page 4
724-746-5500 | blackbox.com
Installation Instructions
Step 6: Cable arms: Attach the two cable management arms using three 11⁄2
"
clevis pins.
NOTE: You can install cable management on the opposite side.
(3) clevis pins and cotter pins
(pins install from bottom)
(2) arms
(identical)
Figure 5. Attaching the cable arms.
Step 7: Monitor attachment. See Figure 6.
Step 7A: Turn the monitor face down on a large flat surface.
Step 7B: Locate the four VESA mounting holes on the rear of the monitor.
Step 7C: Determine if spacers are required. Some monitors have a “recess” on
the rear of the monitor. Spacers are provided to fill this gap. See Table 1
for spacer length options.
Step 7D: Determine the screw length. Only use the metric M4 screws provided.
Screw length is determined by the spacers used. See Table 1.
SMM4-2U
Page 5
724-746-5500 | blackbox.com
Installation Instructions
(4) screws
Spacers
Monitor
(upside-down)
VESA hole
pattern
Bottom of
monitor
Recess
Figure 6. Attaching the monitor.
SMM4-2U
Page 6
724-746-5500 | blackbox.com
Installation Instructions
Table 1. Monitor hardware pack.
Recess depth Spacer/screw
Length
0.125 (1⁄8")
12-mm
0.500 (1⁄2")
0.750 (3⁄4")
25-mm
30-mm
SMM4-2U
Page 7
724-746-5500 | blackbox.com
Black Box Tech Support: FREE! Live. 24/7.
Tech support the
way it should be.
Great tech support is just 30 seconds away at
724-746-5500 or blackbox.com.
About Black Box
Black Box provides an extensive range of networking and infrastructure products.
You’ll find everything from cabinets and racks and power and surge protection
products to media converters and Ethernet switches all supported by free, live 24/7
Tech Support available in 30 seconds or less.
© Copyright 2012. Black Box Corporation. All rights reserved. Black Box® and the Double Diamond logo
are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in this manual
are acknowledged to be the property of their respective owners.
SMM2-2U, version 2
724-746-5500 | blackbox.com
|