KW750
P
G
H
I
J
3
(Original instructions)
ENGLISH
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Intended use
Your Black & Decker planer has been designed for planing wood,
wood products and plastics. The tool is intended for hand-
held use. This tool is intended for consumer use only.
3. Personal safety
Safety instructions
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
General power tool safety warnings
Warning! Read all safety warnings and all
@
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
2. Electrical safety
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4
(Original instructions)
ENGLISH
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
Warning! Contact with, or inhalation of dusts arising from
planing applications may endanger the health of the operator
and possible bystanders. Wear a dust mask specifically de-
signed for protection against dust and fumes and ensure that
persons within or entering the work area are also protected.
u This tool is not intended for use by persons (including
children) with reduced physical, sensory or mental capa-
bilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety of others
5. Service
u This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings
u Children should be supervised to ensure that they do not
play with the appliance.
Warning! Additional safety warnings for planers
@
u Hold the power tool by insulated gripping surfaces
only, because the cutter may contact its own cord.
Cutting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric
shock.
Residual risks.
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the work by your hand or against the body leaves it unsta-
ble and may lead to loss of control.
u Wait for the cutter to stop before setting the tool
down. An exposed rotating cutter may engage the surface
leading to possible loss of control and serious injury.
u Keep the cutter sharp. Dull or damaged cutters may
cause the planer to swerve or stall under pressure. Always
use the appropriate type of cutter for the power tool.
u Do not touch the workpiece or the cutter immediately after
operating the tool. They can become very hot.
u Remove all nails and metal objects from the workpiece
before planning.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
u Always hold the tool with both hands and by the handles
provided.
u Immediately disconnect the cable from the mains if it is
damaged or cut.
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by EN
60745 and may be used for comparing one tool with another.
The declared vibration emission value may also be used in a
preliminary assessment of exposure.
5
(Original instructions)
ENGLISH
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
Fitting
u Slide the blade into the holder until it is against the end
stop.
u Tighten the bolts using the spanner supplied.
Warning! Always replace both cutters.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Adjusting the depth of cut (fig. B)
The depth of cut is indicated by the marking (9). The setting
range can be read from the graduation (6).
u Turn the planing depth adjustment knob (5) to the required
depth of cut.
u Turn the knob to the ‘P' postion whenever the tool is not in
use.
Labels on tool
The following pictograms are shown on the tool:
Fitting and removing the parallel fence (fig. C)
The parallel fence is used to for optimum control on narrow
workpieces.
u Thread the knob (11) into the hole on the side of the
planer and securely tighten.
Warning! To reduce the risk of injury, the user must
:
read the instruction manual.
Electrical safety
u Loosen the parallel fence adjustment knob (10).
u Slide the parallel fence into the desired position.
u Securely tighten the parallel fence adjustment knob.
Note : The parallel fence should be below the planer when
installed correctly.
This tool is double insulated; therefore no earth wire
#
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
u To remove the parallel fence proceed in reverse order.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Connecting a vacuum cleaner to the tool (fig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
local Black & Decker retailer.
u Slide the adaptor (12) over the shavings discharge outlet
(3).
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
u Connect the vacuum cleaner hose (13) to the adaptor.
3. Shavings discharge outlet
4. Shavings discharge outlet selector
5. Planing depth adjustment knob
6. Planing depth graduation
Fitting the shavings collection bag (fig. E)
The shavings collection bag is particularly useful when working
in confined spaces.
Assembly
u Slide the connecting plate (14) of the bag over either side
of the shavings discharge outlet (3).
u To prevent chips from coming out opposite side of shav-
ings discharge outlet, move the shavings discharge outlet
selector (4) to the opposite side from the bag.
Warning! Before assembly, make sure that the tool is switched off
and unplugged.
Replacing the cutting blades (fig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
Emptying the shavings collection bag
The shavings collection bag should be emptied regularly while
using it to prevent blocking.
Removing
u Unzip the bag and empty it before continuing.
u Loosen the bolts (7) using the spanner supplied.
u Slide the blade (8) out of the holder.
u Reverse the blade so that the unused side comes in posi-
tion. If both sides are worn, the blade must be replaced.
6
(Original instructions)
ENGLISH
Use
Accessories
Warning! Let the tool work at its own pace. Do not overload.
u Adjust the depth of cut.
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the performance
of your tool. By using these accessories you will get the very
best from your tool.
u If necessary, fit and adjust the parallel fence.
Switching on and off
The following types of cutting blades can be obtained from
your local retailer:
Switching on
u Keep the lock-off button (2) depressed and press the on/
off switch (1).
u Release the lock-off button.
- Tungsten carbide tipped reversible cutting blades (part
no. X35007, supplied per pair)
- High-speed steel reversible cutting blades (part no.
X24192-XJ11, supplied per pair)
Switching off
u Release the on/off switch.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Planing
u Hold the tool with the nose piece of the shoe resting on
top of the workpiece surface.
u Switch the tool on.
Warning! Before performing any maintenance, switch off and
unplug the tool.
u Move the tool steadily forward to perform the cutting
stroke.
u Regularly clean the ventilation slots in your tool using a
soft brush or dry cloth.
u Switch the tool off after the stroke has been completed.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Rebating (fig. F)
u Fit and adjust the parallel fence.
u Proceed as for planing.
Replacing the drive belt (fig. I)
u Loosen the screws (15) and remove the cover (16).
u Remove the old drive belt.
u Place the new belt (17) over the pulleys. Place the belt
over the large pulley (18) first, then over the small pulley
(19), whilst manually rotating the belt steadily.
u Put the cover back in place and tighten the screws.
Chamfering edges (fig. G)
The V-groove in the nose piece of the shoe enables you to
chamfer edges at 45°, 30° and 15° angles.
u Hold the tool at an angle with the desired groove (20)
around the edge of the workpiece and perform the cutting
stroke.
Motor brush inspection and replacement (fig. J)
Brushes should be regularly inspected for wear.
u Remove brush cap (22). The brushes should slide freely
in brush box. If brushes are worn down to .3" (8mm) they
should be replaced.
To reinstall, push new brush back into brush box. If replacing
existing brush, maintain same orientation as when removed.
Replace the brush cap (do not overtighten).
Parking rest (fig. H)
Your planer is equipped with a parking rest (21) that automati-
cally lowers into place when the tool is lifted from the work
surface. When planing, the parking foot raises as the tool is
pushed forward. When the parking foot is lowered, the planer
can set on the work surface without the blade touching.
Hints for optimum use
u Move the tool along the grain of the wood.
u If the grain is cross or curly, or if the workpiece material is
a hard type of wood, adjust the depth of cut to take only a
very thin shaving at each pass and take several passes to
achieve the desired result.
u To keep the tool in a straight line, press down the front of
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
7
(Original instructions)
ENGLISH
Protecting the environment
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah) <2.5 m/s2
Separate collection. This product must not be
disposed of with normal household waste.
Z
uncertainty (K) 1.5 m/s2
Should you find one day that your Black & Decker product
needs replacement, or if it is of no further use to you, do not
dispose of it with household waste. Make this product available
for separate collection.
Level of sound pressure according to EN 60745:
Sound pressure (LpA) 83.9 dB(A), uncertainty (K) 3 dB(A)
Sound power (LWA) 94.9 dB(A), uncertainty (K) 3 dB(A)
Separate collection of used products and packaging
z
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent environ-
mental pollution and reduces the demand for raw
materials.
EC declaration of conformity
MACHINERY DIRECTIVE
Local regulations may provide for separate collection of elec-
trical products from the household, at municipal waste sites or
by the retailer when you purchase a new product.
%
KW750
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this service
please return your product to any authorised repair agent who
will collect them on our behalf.
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, 2004/108/EC
EN 60745-1, EN 60745-2-14
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at
the address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of our
after-sales service and contacts are available on the Internet
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
Technical data
Kevin Hewitt
Vice-President Global Engineering
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
KW750 (Type 4)
_
Input voltage
Power input
No-load speed
Planing width
Planing depth
Rebating depth
Weight
Vac
W
230
750
16,500
82
United Kingdom
11/11/2010
min-1
mm
mm
mm
kg
2
12
2.9
8
(Original instructions)
ENGLISH
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement is
in addition to and in no way prejudices your statutory rights.
The guarantee is valid within the territories of the Member States
of the European Union and the European Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24 months
from the date of purchase, Black & Decker guarantees to
replace defective parts, repair products subjected to fair
wear and tear or replace such products to ensure minimum
inconvenience to the customer unless:
u The product has been used for trade, professional or hire
purposes;
u The product has been subjected to misuse or neglect;
u The product has sustained damage through foreign
objects, substances or accidents;
u Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent
by contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
to register your new Black & Decker product and to be kept up
to date on new products and special offers.
Further information on the Black & Decker brand and our range
9
ENGLISH
Do not forget to register your product!
Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product
code to Black & Decker in your country.
11
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel. 03-8720 5100
Fax 03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel. +64 9 259 1133
Fax +64 9 259 1122
Auckland 1060
United Kingdom
Black & Decker
210 Bath Road
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
Slough, Berkshire SL1 3YD
90568936 REV-1
11/2010
|