UK
Ireland
Australia
New Zealand
After use
X
Intended use
Switch off and remove the plug from the socket before
Your Black & Decker Glue Gun has been designed for leisure
and DIY activities in the home to join materials together
including paper, card and material.
leaving the appliance unattended and before changing,
cleaning or inspecting any parts of the appliance.
When not in use, the appliance should be stored in a dry
place. Children should not have access to stored
appliances.
X
This tool is intended for consumer use only.
Safety instructions
Warning! When using mains-powered appliances, basic
safety precautions, including the following, should always be
followed to reduce the risk of fire, electric shock, personal injury
and material damage.
Inspection and repairs
X
Before use, check the appliance for damaged or defective
parts. Check for breakage of parts, damage to switches and
any other conditions that may affect its operation.
Do not use the appliance if any part is damaged or
defective.
Have any damaged or defective parts repaired or replaced
by an authorised repair agent.
Before use, check the power supply cord for signs of
damage, ageing and wear.
Do not use the appliance if the power supply cord or mains
plug is damaged or defective.
If the power supply cord or mains plug is damaged or
defective it must be repaired by an authorised repair agent
in order to avoid a hazard. Do not cut the power supply cord
and do not attempt to repair it yourself.
X
Read all of this manual carefully before using the
appliance.
X
X
X
X
X
X
The intended use is described in this manual. The use of
any accessory or attachment or the performance of any
operation with this appliance other than those
recommended in this instruction manual may present a risk
of personal injury.
X
Retain this manual for future reference.
Using your appliance
X
Keep work area clean and well lit. Cluttered and dark areas
invite accidents.
X
Do not expose the appliance to rain or wet conditions.
Water entering the appliance will increase the risk of
electric shock.
X
Never attempt to remove or replace any parts other than
those specified in this manual.
X
Stay alert, watch what you are doing and use common
sense when operating the appliance. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Never pull the power supply cord to disconnect the plug
from the socket. Keep the power supply cord away from
heat, oil and sharp edges.
If the power supply cord is damaged during use, disconnect
the appliance from the power supply immediately. Do not
touch the power supply cord before disconnecting from the
power supply.
Specific safety instructions for glue guns
Warning! This appliance must be placed on the stand when not
in use.
DO NOT TOUCH THE HEATED nozzle of the Glue Gun.
The operating temperature of this appliance is
approximately 199°C.
X
X
Keep hands away from the heated attachment and
work area. Heat may be conducted through the work piece.
Use clamps or pliers to hold the work piece.
The heating element will begin to heat up as soon as
the appliance is plugged in. To avoid injury or damage to
property always assume that the appliance is hot and return
it to the stand.
X
Disconnect the appliance from the power supply when not
in use, before fitting or removing parts and before cleaning.
Protect the work surface and materials from heat
damage. Heat may be conducted through the work piece.
Use a heat resistant material to protect the work surface.
Safety of others
X
Do not allow children or any person unfamiliar with these
instructions to use the appliance.
Glue sticks are not intended for ingestion and should
not come in contact with food, etc. If swallowed, seek
medical attention. Keep out of the reach of children.
X
Do not allow children or animals to come near the work
area or to touch the appliance or power supply cord. Close
supervision is necessary when the appliance is used near
children.
Before cleaning, adjustment or changing the attachments.
Unplug the appliance and allow the attachment to cool.
Never attempt to force cool the appliance after use by
immersing any part of it in water or any other liquid.
Allow the appliance to air cool only.
3
Keep the appliance away from all flammable material.
Be aware that this product may ignite material. Where this
is a concern, test a piece of scrap material.
Features
1. Trigger
2. Handle
Never leave the appliance plugged in and unattended.
After use, unplug the appliance, allow the attachment to
cool and store in a safe place out of the reach of children.
3. Stand
4. Wire stand
5. Ready for use indicator
Fumes resulting from heating materials for craft
activities may be hazardous. Always work in a well
ventilated area. Seek advice on the materials being used.
Assembly
Warning! Before cleaning, adjustment or changing the
attachments. Unplug the appliance and allow the attachment to
cool.
Never attempt to insert any material other than
recommended glue sticks, sealer, or caulk sticks in
the glue gun. For example: Do not attempt to melt crayons
or candles.
Power connection (fig. A & B)
The appliance can be used either in cordless or corded mode.
DO NOT use hot melt glue to take the place of
structural fasteners.
In cordless mode the power supply is taken from the stand
(3) to heat the element. This is suitable for small tasks where
a small amount of glue is required.
The glue sticks used with this glue gun will begin to
soften at about 60°C. Don't use the glue on objects or
materials that are subjected to heat.
The heating element will start to cool as soon as the
appliance is removed from the stand (3). When the ready for
use indicator (5) changes to grey, or when the glue is no
longer flowing freely, return the appliance to the stand (3).
Avoid accidental glue discharge. Forcing glue sticks into
an unheated appliance may damage the appliance or cause
hot glue to be unexpectedly expelled from nozzle when the
operating temperature is achieved. Glue may discharge from
a heated appliance without pressure applied to the trigger
(1). Return the appliance to the stand and use a heat
resistant material to protect the work surface.
In corded mode the connector (6) can be removed from the
stand (3) and inserted directly into the appliance. This is
suitable for heavy duty tasks.
Changing from cordless to corded operating mode
(fig. C & D)
This appliance is not a toy. Keep out of the reach of
children.
X
Remove the plug from the socket.
X
Push down on the two tabs in front of the connector (6) as
shown.
Safety symbols marked on appliance
X
Rotate the connector (6) toward the inside of the stand (3)
and lift the receptacle and cord out of the holder.
Rotate the wire stand (4) forward (fig. D).
Insert the connector (6) into the handle (2) of the appliance
(cord facing the back of the unit).
Hot surface do not touch.
X
X
Appliance only to be used with the stand
supplied.
Changing from corded to cordless operating mode
X
Remove the plug from the power supply socket.
Remove the connector (6) from the handle (2) of the
appliance.
X
Electrical safety
This appliance is double insulated; therefore no
earth wire is required. Always check that the
power supply corresponds to the voltage on the
rating plate.
X
With the cable facing the rear of the stand (3) and the
connections upwards insert the front of the connector (6)
into the stand (3) location.
X
Push the rear of the connector (6) down to lock it in position.
This appliance is not intended for use by young or infirm
persons without supervision. Children must be supervised to
ensure they do not play with the appliance.
Fitting and removal of a glue tip attachment (fig. E)
There are three different attachments:
X
X
X
X
Standard (7)
Extended angle (8)
Wide (9)
A wrench is included to change the attachment; it is stored
in the stand (3).
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
4
X
Use the wrench to rotate the glue tip attachment anti
clockwise.
the material. Clamps or pliers should be used to protect the
operator from the heat.
X
X
Working in a cold environment will reduce the time
required for the glue to harden. Warm environments will
increase the time for the glue to set.
The amount of glue applied will affect the hardening time.
Large heavy pools of glue will take up to fifty percent longer
to dry than small drops. Very thin beads will dry in as few
as 10 seconds. Some experimentation with your glue gun
on scrap material will help to determine the best method to
use for your particular project.
Some paints and stains containing petroleum distillates
can weaken the adhesive. Test before using. You may need
to paint or stain before gluing.
Excess glue is not easily removed from materials when it
has hardened. Removal of excess glue may be attempted
by scraping, peeling, or softening the glue by applying heat
e.g. with the hot tip of the appliance. Adhesive may be
removed from fabric by dry cleaning.
Removing and changing attachments
Install the attachment and rotate it clockwise to tighten.
X
Fitting a glue stick
Replacement glue sticks are available from your Black &
Decker dealer (cat. no. X72020-QZ)
X
X
X
Insert a stick of hot melt glue into the inlet tube located at
the rear of the appliance.
Gently squeeze the trigger (1) to locate the glue stick firmly
in position. Place the appliance into the stand (3) (Fig, A).
On first use, the glue stick may be completely inserted into
the appliance. A second glue stick may be required.
X
X
Warning! Do not attempt to remove an unused portion of a
glue stick from the appliance.
Use
Warning! Be aware that this product may ignite material.
Where this is a concern, test a piece of scrap material.
Maintenance
This appliance will become quite warm during use. This is
normal and does not indicate a problem. Avoid contact with
the tip housing and attachment.
Your Black & Decker appliance has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper care
and regular cleaning.
Turning the appliance on
X
Regularly clean the appliance using a damp cloth. Do not
use any abrasive or solvent-based cleaner. Never let any
liquid get inside the appliance and never immerse any part
of the appliance into liquid.
Do not turn the appliance on without a glue stick fitted.
X
To turn the appliance on, insert the plug into an appropriate
socket. The heating element will begin to heat up as soon
as the appliance is plugged in.
X
X
Wait until the ready for use indicator (5) turns from grey to
red (Fig B).
Apply glue by squeezing the trigger (1). When the gun stops
feeding glue, release the trigger (1) and squeeze again for
additional flow. When the glue stick is pressed to the level
of the inlet tube lip, insert another stick.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
X
X
X
X
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the new plug.
Connect the blue lead to the neutral terminal.
Connect the green/yellow lead to the earth terminal.
Hints for Optimum Use
Warning! Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 3 A.
The basic instructions given below are provided as a guide to
craft and DIY applications. The operator should practise the
various applications on scrap materials to obtain the
required effect and prevent damage to the work piece.
Protecting the environment
Should you find one day that your appliance needs
replacement, or if it is of no further use to you,
think of the protection of the environment. Black &
Decker repair agents will accept old Black &
Decker tools and ensure that they are disposed of
in an environmentally safe way.
Tips on using your glue gun
X
Choose the right glue stick for the right application. Only
use high or multi-temperature round glue sticks suitable for
this appliance.
X
X
X
Make sure that the surfaces are clean and free from dirt or
oily films before gluing.
Assemble the parts to confirm that they can be joined
together in the required position before applying glue.
Make arrangements to hold the parts in position while the
glue hardens. The heat from the glue may be conducted to
Separate collection of used products and
packaging allows materials to be recycled and
used again. Re-use of recycled materials helps
prevent environmental pollution and reduces the
demand for raw materials.
5
Local regulations may provide for separate collection of
electrical products from the household, at municipal waste
sites or by the retailer when you purchase a new product.
make sure of the minimum inconvenience to the customer
unless:
X
The product has been used for trade, professional or hire
purposes.
Black & Decker provides a facility for the collection and
recycling of Black & Decker products once they have reached
the end of their working life. To take advantage of this
service please return your product to any authorised repair
agent who will collect them on our behalf.
X
X
The product has been subjected to misuse or neglect.
The product has sustained damage through foreign objects,
substances or accidents.
X
Repairs have been attempted by persons other than
authorised repair agents or Black & Decker service staff.
You can check the location of your nearest authorised repair
agent by contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a list of
authorised Black & Decker repair agents and full details of
our after-sales service and contacts are available on the
Internet at: www.2helpU.com.
To claim on the guarantee, you will need to submit proof of
purchase to the seller or an authorised repair agent. You can
check the location of your nearest authorised repair agent by
contacting your local Black & Decker office at the address
indicated in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our after-
sales service and contacts are available on the Internet at:
Technical data
GG500
Voltage
Frequency
Vac
Hz
230-240
50
register your new Black & Decker product and to be kept up
to date on new products and special offers. Further
information on the Black & Decker brand and our range of
Rated Input
W
25
Operating temperature
Glue stick diameter
Weight
°C
mm
kg
199
12
0.3
EC declaration of conformity
GG500
Black & Decker declares that these products conform to:
Standards & Legislation.
89/336/EEC, 73/23/EC, EN60335, EN55014, EN50336
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham
DL16 6JG,
United Kingdom
31-09-2006
Guarantee
Black & Decker is confident of the quality of its products and
offers an outstanding guarantee. This guarantee statement
is in addition to and in no way prejudices your statutory
rights. The guarantee is valid within the territories of the
Member States of the European Union and the European
Free Trade Area.
If a Black & Decker product becomes defective due to faulty
materials, workmanship or lack of conformity, within 24
months from the date of purchase, Black & Decker
guarantees to replace defective parts, repair products
subjected to fair wear and tear or replace such products to
6
7
8
9
10
11
496011-00
10/06
|