GLC120
13
14
2
1
3
4
5
6
7
8
9
10
11
12
A
3
13
18
16
17
14
20
18
19 16 17
15
8
B
C
26 27 24
4
5
32
25
9
22
21
23
D
4
E
30
29
28
31
F
G
33
35 34
32
I
H
5
4
5
K1
J
K2
6
L
2
1
6
10
M
N
36
O
7
37
38
39
P
8
E N G L I S H
CORDLESS GRASS TRIMMER GLC120
CONGRATULATIONS!
INTENDED USE
You have chosen a Black & Decker tool. Our aim is
to provide quality tools at an affordable price. We
hope that you will enjoy using this tool for many
years.
Your Black & Decker grass trimmer GLC120 has
been designed for trimming and finishing lawn
edges and to cut grass in confined spaces.
This tool is intended for consumer use only.
Your Black & Decker charger has been designed
for charging Black & Decker batteries of the type
supplied with this tool.
EC DECLARATION OF CONFORMITY
GLC120
Black & Decker declares that these tools
conform to: 98/37/EC, 89/336/EEC,
73/23/EEC, EN 60335, EN 786, EN 50260,
EN 55014, EN 61000
SAFETY INSTRUCTIONS
Warning symbols
The following symbols are used in this manual:
Level of sound pressure, measured according to
84/538/EEC:
Denotes risk of personal injury, loss of life
or damage to the tool in case of non-
observance of the instructions in this
manual.
GLC120
LpA (sound pressure)
LWA (acoustic power)
dB(A)
dB(A)
83
96
Denotes risk of electric shock.
Always wear ear protection if the sound
pressure exceeds 85 dB(A).
Read the manual prior to operation.
Hand/arm weighted vibration value according to
98/37/EC:
Fire hazard.
GLC120
< 2.5 m/s2
Know your tool
◆
Warning! When using battery-powered
tools, basic safety precautions,
including the following, should always
be followed to reduce the risk of fire,
leaking batteries, personal injury and
material damage.
◆
◆
Read all of this manual carefully before
operating the tool.
Before operating the tool, make sure
that you know how to switch it off in an
emergency.
Colin Dyke
Vice President of Engineering
Brockville, Ontario K6V 5W6
Canada
9
E N G L I S H
◆
The intended use is described in this
Inspection and repairs
manual. The use of any accessory or
attachment or performance of any
operation with this tool other than
those recommended in this instruction
manual may present a risk of personal
injury.
◆
Before use and after any impact, check the tool
for damaged or defective parts. Check for
misalignment and seizure of moving parts,
breakage of parts, damage to guards and
switches and any other conditions that may
affect its operation. Check if the lock-off button
functions properly.
◆
Retain this manual for future reference.
◆
Do not use the tool if any part is damaged or
defective. Do not use the tool if the switch
does not turn it on and off.
Work area
◆
Do not expose the tool to rain. Do not use the
tool in damp or wet conditions.
Only use the tool in daylight or good artificial
light.
◆
◆
◆
◆
Never use the tool when any guard or
enclosure is damaged or not in place.
Ensure that the tool will operate properly and
perform its intended function.
Have any damaged or defective parts repaired
or replaced by an authorised repair agent.
Never attempt to remove or replace any parts
other than those specified in this manual.
Use only Black & Decker replacement parts
and accessories.
◆
Personal protection
◆
Wear stout shoes or boots to protect your feet.
Do not operate the tool wearing open-toed
sandals or when barefoot.
◆
Wear long trousers to protect your legs.
Using your tool
◆
Stay alert. Watch what you are doing. Use
common sense.
Additional safety instructions for grass trimmers
The following warning symbols are found on the tool:
◆
◆
Do not operate the tool when you are tired.
If the tool begins to vibrate abnormally,
immediately switch it off. Allow rotating parts
to stop and inspect the tool for damage and
loose parts.
Wear safety glasses or goggles when
operating this tool.
The cutting line will continue to run for a
few seconds after switching the tool off.
Never attempt to force the line to come
to a standstill.
Safety of others
◆
◆
◆
Do not allow children or any person unfamiliar
with these instructions to operate the tool.
Do not allow children, visitors or animals to
come near the work area or to touch the tool.
Remember that the operator may be held
responsible for accidents or hazards occurring
to other people or their property.
Keep people and animals at least 6 m
away from the cutting area.
Do not expose the tool to rain or high
humidity.
After use
◆
Switch the tool off and ensure that moving
◆
◆
Before using the tool, check that your cutting
path is free from sticks, stones, wire and any
other objects.
Only use the tool in the correct position,
with the cutting line near the ground, as shown
in the illustrations. Never switch the tool on in
any other position.
parts have stopped rotating before leaving
the tool unattended and before changing,
cleaning or inspecting any parts of the tool.
When not in use, the tool should be stored
in a dry place. Children should not have access
to stored tools.
◆
10
E N G L I S H
◆
◆
◆
Switch on the tool only when hands and feet
are away from the cutting line.
Avoid body contact with the cutting line while
the tool is running.
Do not work on steep slopes. Be sure of your
footing. Be aware that freshly cut grass is
damp and slippery.
◆
◆
In case of skin contact, flush immediately with
water. Neutralize with a mild alkaline solution
such as milk or bicarbonate of soda.
In case of eye contact, rinse abundantly with
clean water for at least 10 minutes.
Seek medical attention.
◆
Take care when trimming near borders and
gravel paths or roads, as stones and soil may
be moved by the cutting line.
The following symbol is found on the battery:
◆
◆
Do not put the tool down until the cutting line
has come to a complete standstill.
Use only the appropriate type of
Do not incinerate the battery.
Black & Decker cutting line. Never use metal
cutting line or fishing line.
Charger
◆
Use your Black & Decker charger only to
charge batteries of the type supplied with your
tool. Other batteries could burst, causing
personal injury and damage.
◆
Take care to avoid injury from the line
trimming blade. Do not touch the blade. After
extending new cutting line, always return the
tool to its normal operating position before
switching on.
◆
◆
◆
◆
Have defective cords replaced immediately.
Do not expose to water.
Do not open the charger.
Additional safety instructions for batteries and
chargers
Do not probe the charger.
The following symbol is found on the charger:
Intended for indoor use only.
Battery
◆
Never attempt to open for any reason.
Do not store in locations where the
temperature may exceed 40 °C.
Charge only at ambient temperatures between
5 °C and 40 °C.
◆
ELECTRICAL SAFETY
◆
Your charger has been designed for a specific
mains voltage. Always check that the mains
voltage corresponds to the voltage on the rating
plate.
◆
◆
Charge only in a dry, well ventilated area.
Charge only using the charger provided with
the tool.
◆
◆
Do not attempt to charge damaged batteries.
Before charging, make sure that the battery
connector is dry and clean.
When disposing of the battery, follow the
instructions given in the section “Protecting
the environment”.
The charger is designed for use on AC
(mains) power supplies only. Do not
attempt to use on any other supply.
◆
Your charger is double insulated in
accordance with EN 60335; therefore no
earth wire is required.
Under extreme conditions, battery leakage may
occur.
Never attempt to replace the charger unit
with a regular mains plug.
The battery liquid contains diluted
sulphuric acid which can be harmful.
Sulphuric acid on the skin will cause burns
and if in contact with the eyes may cause
loss of sight.
11
E N G L I S H
CARTON CONTENTS
The carton contains:
◆
◆
◆
Find a suitable indoor location for the wall
mount. If you also want to charge the battery
on the wall mount, this location must be dry
and well ventilated.
Position the wall mount as shown and mark the
location of the two mounting holes (16) on the
wall. Make sure that there is sufficient space to
hang the tool on the wall mount.
1
1
1
1
2
2
1
Cordless grass trimmer
Charger
Guard with mounting screw
Wall mount
Mounting screws
Wall plugs
Instruction manual
Drill a hole (ø 6 mm, approx. 35 mm deep) at
each of the marked locations.
◆
Carefully unpack all parts.
◆
◆
Insert the plugs (17) provided into the holes.
If you do not want to use the wall mount
location for charging the battery, remove the
charging insert from the wall mount.
If you want to use the wall mount location for
charging the battery:
- Guide the cable (19) through one of the slots
(20) as shown.
- Plug the charger (13) into a mains outlet.
Mount the wall mount to the wall using the
screws (18) provided.
OVERVIEW (fig. A)
1. On/off switch
2. Lock-off button
3. Battery housing
4. Secondary handle
5. Handle knob
6. Head release knob
7. Motor housing
8. Guard
◆
◆
9. Line trimming blade
10. Edge guide
11. Spool
12. Cutting line
13. Charger
Fitting the secondary handle (fig. D)
◆
◆
◆
Unscrew the handle knob (5).
Set the handle onto the tool as shown.
Fasten the handle using the handle knob and
screw as shown.
14. Wall mount
ASSEMBLY
USE
Avoid accidentally switching the tool on
during assembly.
Let the tool work at its own pace.
Do not overload.
Fitting the guard (fig. B)
Charging the battery (fig. G & H)
◆
◆
◆
◆
Remove the screw (15) from the guard (8).
Place the guard onto the tool as shown.
Firmly press the guard until it snaps into place.
Secure the guard with the screw (15).
The battery needs to be charged before first use
and whenever it fails to produce sufficient power
on jobs that were easily done before. To maximise
the lifetime of the battery, it is recommended to
keep the battery connected to the charger
whenever the tool is not in use. When the battery
is full, the power consumption of the charger is
negligible.
Never use the tool unless the guard is
properly fitted.
Mounting the wall mount to the wall (fig. C)
The wall mount (14) is used to provide a convenient
storage and charging point for the tool.
Do not charge the battery at ambient
temperatures below 5 °C or above 40 °C.
Recommended charging temperature:
approx. 24 °C.
12
E N G L I S H
◆
To charge the battery on the wall base:
- Make sure the charging insert (21) is fitted in
the wall mount (14) (fig. C).
Trimming mode (fig. K & M)
For trimming, the trimmer head should be in the
position shown in fig. K. If it is not:
- Hang the tool on the wall mount as shown
(fig. F).
◆
While holding the secondary handle with one
hand, depress the head release knob (6) with
the other hand (fig. M).
◆
To charge the battery elsewhere:
- Insert the plug (32) into the connector (33) on
the battery housing.
- Place the tool on a flat and level surface as
shown.
◆
Rotate the trimmer head clockwise until it
engages in the trimming position.
Release the head release knob.
Set the edge guide (10) to the retracted
position.
◆
◆
◆
◆
Make sure that the tool is out of reach
of children and any other persons
unfamiliar with this tool.
Make sure that the plug and cable are
not trapped under the tool.
Edging mode (fig. L & M)
For edging, the trimmer head should be in the
position shown in fig. L. If it is not:
◆
While holding the secondary handle with one
hand, depress the head release knob (6) with
the other hand (fig. M).
Charging process (fig. I)
Plug the charger into a mains outlet.
◆
Rotate the trimmer head counterclockwise until
it engages in the edging position.
◆
◆
◆
Release the head release knob.
Set the edge guide (10) to the forward position.
While the battery is being charged, the red
indicator light (34) on the charger will be lit.
When charging is complete, the red indicator light
will stop lighting and the green indicator light (35)
will be lit. The battery can be left connected to the
charger indefinitely.
Switching on and off (fig. N)
For your safety, this tool is equipped with a
double switching system. This system is designed
to prevent inadvertent operation of the tool.
When you want to use the tool, disconnect Switching on
the charger from the battery and unplug
the charger.
◆
Push the lock-off button (2) forward using your
thumb and at the same time squeeze the on/
off switch (1).
Adjusting the position of the secondary handle
(fig. A & J)
◆
Release the lock-off button.
The secondary handle can be adjusted to provide
optimum balance and comfort.
Switching off
Release the on/off switch (1).
◆
◆
◆
◆
◆
Let the guard (8) rest on the ground.
Slacken the handle knob (5).
Move the handle (4) into the desired position.
Securely tighten the handle knob.
Never attempt to lock a switch in the on
position.
Hints for optimum use
Setting the tool to trimming or edging mode
(fig. K, L & M)
Trimming
The tool can be used in trimming mode as shown
in fig. K or in edging mode to trim overhanging
grass along lawn edges and flower beds as shown
in fig. L.
◆
Hold the tool as shown in fig. K.
Gently swing the trimmer from side to side as
shown in fig. K.
◆
13
E N G L I S H
◆
When cutting long grass, work in stages from
the top.
Keep the tool away from hard objects and
delicate plants.
◆
◆
Keep the tabs (22) depressed and remove the
spool cover (23) from the housing (24).
Remove the empty spool (25) from the
housing.
Remove any dirt and grass from the housing.
Take the new spool and unwind approx. 10 cm
of cutting line.
◆
◆
If the tool starts running slowly, reduce the load.
◆
◆
Edging
Optimum cutting results are achieved on edges
deeper than 50 mm.
◆
◆
Feed the cutting line through the eyelet (26).
Push the spool onto the drive shaft (27) and
rotate it slightly until it is seated. Make sure
that the cutting line is not trapped under the
spool and that 8-10 cm of cutting line
protrudes from the housing.
Align the tabs on the spool cover with the
holes in the housing.
Push the cover onto the housing until it snaps
securely into place.
◆
◆
◆
Do not use the tool to create edges. To create
edges, use an edging spade.
Guide the tool as shown in fig. L. Keep the
edge guide against the lawn edge.
To make a closer cut, slightly tilt the tool.
◆
◆
General
◆
In order to achieve optimum cutting results,
only cut dry grass.
◆
If possible, keep the battery connected to the
charger and the charger plugged in whenever
the tool is not in use.
If the cutting line protrudes beyond the
trimming blade (9), cut it off so that it just
reaches the blade.
MAINTENANCE
Winding new line onto an empty spool (fig. F)
You may wind new cutting line onto an empty
spool. Replacement packs of cutting line are
available from your Black & Decker dealer (cat. no.
A6170 (25 m), A6171 (40 m), A6054 (50 m)).
Your Black & Decker tool has been designed to
operate over a long period of time with a
minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and
regular cleaning.
◆
Remove the empty spool from the tool as
described above.
Your charger does not require any maintenance
apart from regular cleaning.
◆
◆
Remove any old cutting line from the spool.
Feed 2 cm of cutting line into one of the holes
(28) in the spool as shown.
Unplug the charger before cleaning it.
◆
◆
Bend the cutting line and anchor it in the
L-shaped slot (29).
Wind the cutting line onto the spool in the
direction of the arrow (30). Make sure to wind
the line on neatly and in layers. Do not criss-
cross.
◆
◆
Regularly clean the spool using a soft brush or
dry cloth.
Regularly use a blunt scraper to remove grass
and dirt from the underneath of the guard.
◆
◆
When the wound cutting line reaches the
recesses (31), cut the line. Let the line protrude
approx. 10 cm from the spool and hold a
finger on the line to keep it in place.
Proceed as described above to fit the spool on
the tool.
◆
◆
Regularly clean the ventilation slots in your tool
using a soft brush or dry cloth.
Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
Fitting a new spool of cutting line (fig. E)
Replacement spools of cutting line are available
from your Black & Decker dealer (cat. no. A6481).
Only use the appropriate type of
Black & Decker cutting line.
14
E N G L I S H
Storage
If the automatic line feed still does not work or the
spool is jammed, try the following suggestions:
When the tool will not be used for several months,
ideally leave the battery connected to the charger.
Otherwise proceed as follows:
◆
Carefully clean the spool cover and housing.
Remove the spool and check if the lever (32)
can move freely (fig. E).
◆
◆
Fully charge the battery.
◆
Store the tool in a secure and dry location.
The storage temperature must always remain
in the range of +5 °C to +40 °C.
Before using the tool after prolonged storage,
fully charge the battery again.
◆
◆
Remove the spool and unwind the cutting line,
then wind it on neatly again as described
above. Replace the spool as instructed.
Push the cover onto the housing until it snaps
securely into place.
◆
TROUBLESHOOTING
PROTECTING THE ENVIRONMENT
If your tool seems not to operate properly, follow
the instructions below. If this does not solve the
problem, please contact your local Black & Decker
repair agent.
Tools
Should you find one day that your tool
needs replacement, or if it is of no further
use to you, think of the protection of the
environment. Black & Decker repair agents
will accept old Black & Decker tools and
ensure that they are disposed of in an
environmentally safe way.
Tool runs slowly
◆
Check that the spool housing can rotate freely.
Carefully clean it if necessary.
◆
Check that the cutting line does not protrude
more than 10-12 cm from the spool housing.
If it does, cut it off so that it just reaches the
line trimming blade.
Battery (fig. O & P)
◆
Connect the battery to the charger and plug
the charger in. Wait until the green indicator
light lights up to ensure that the battery is fully
charged.
If you want to dispose of the tool yourself,
the battery must be removed as described
below and disposed of in accordance with
local regulations.
Pb
Automatic line feed does not work
◆
Keep the tabs depressed and remove the
spool cover from the spool.
◆
The battery liquid contains diluted
sulphuric acid which can be harmful.
Sulphuric acid on the skin will cause
burns and if in contact with the eyes
may cause loss of sight. In case of skin
contact, flush immediately with water.
Neutralize with a mild alkaline solution
such as milk or bicarbonate of soda. In
case of eye contact, rinse abundantly
with clean water for at least 10 minutes.
Seek medical attention.
◆
Lift the spool approx. 6 mm and pull the
cutting line until it protrudes 8-10 cm from the
housing. If insufficient cutting line is left on the
spool, install a new spool of cutting line as
instructed above.
Push the spool back into place and rotate it
slightly until it is seated.
Align the tabs on the spool cover with the
holes in the housing.
Push the cover onto the housing until it snaps
securely into place.
If the cutting line protrudes beyond the
trimming blade, cut it off so that it just reaches
the blade.
◆
◆
◆
◆
◆
◆
Do not short-circuit the battery
terminals.
Be aware that the battery is heavy.
◆
◆
If possible, operate the tool to run the battery
down completely.
Remove the secondary handle from the tool.
15
E N G L I S H
◆
Place the tool on a firm surface, allowing
access to the screws (36) in the handle casing
(fig. O).
◆
◆
Repairs have not been attempted by anyone
other than our authorised repair agents.
The failure represents normal wear and tear.
◆
◆
◆
Remove the screws (36) from the handle casing.
Remove the top part of the handle casing.
Remove the screws (37) from the battery
housing (fig. P).
This guarantee is offered as an extra benefit and
does not affect your statutory rights.
The guarantee policy
◆
◆
Remove the top part of the battery housing.
Disconnect the wires (38) from the battery
terminals (39).
Place the battery in a suitable packaging to
ensure that the terminals cannot be short-
circuited. Take the battery to your service
agent or a local recycling station. Collected
batteries will be recycled or disposed of
properly.
The following failures are not covered by the
above guarantee:
◆
Replacing worn or damaged blades, nylon
lines, chains and power cables. These items
are regarded as replacement items which wear
during normal usage.
◆
◆
◆
Failures as a result of sudden impact or
obvious abuse.
Failures due to usage not in accordance with
instructions and recommendations contained
in this manual.
Technical data
GLC120
Voltage
VDC
Ah
min-1
m
12
The use of other than genuine Black & Decker
accessories and parts may cause decreased
performance or damage to the product and will
render the guarantee void.
Capacity
7.2
No-load speed
Cutting line length
Weight
10,800
10
kg
4.6
AFTER SALES SERVICE
Charger
Full details on our after-sales service are available
Alternatively, contact our Service and Information
Centre at the address towards the back of this
manual.
Input voltage
VAC
h
230
16
Approx. charging time
GUARANTEE
The Black & Decker lawn and garden guarantee
provides: 36 months parts and 12 months
labour cover in the UK, 24 months parts and
labour cover in South Africa, Australia and New
Zealand. Proof of purchase will be required.
Should your Black & Decker product become
defective within the guarantee period due to
faulty materials or workmanship, we guarantee to
either replace all defective parts or -at our
discretion- to replace the unit free of charge,
provided that:
It is our aim that all Black & Decker customers
should be totally satisfied with their
Black & Decker product and our after sales service.
If any help or advice is needed, please contact
your local Black & Decker repair agent.
If your product needs repair, please take or send it
to an authorised repair agent, providing proof of
purchase if claiming a guarantee repair.
Black & Decker offers a nationwide network of
authorised repair agents.
◆
◆
◆
The product is returned to us or one of our
authorised repair agents with proof of purchase.
The product has been used within the
parameters of its consumer classification.
The product has not been used for hire
purposes.
Full details on our after sales service can be
obtained from any of our authorised repair agents.
16
E N G L I S H
OTHER OUTDOOR TOOLS
Black & Decker has a full range of outdoor power
tools that make life in the garden easy. If you
would like further information on the following
products, please contact our Service and
Information Centre (see the address page towards
the end of this manual) or your local
Black & Decker retailer.
String trimmers
Cordless shear
Lawnmowers
Leafbusters
Chainsaws
Hedgetrimmers
Lawnrakers
Shredders
Not all products are available in all countries.
17
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Tel. 03 9895 9200
Fax 03 9899 7465
Box Hill, Victoria 3128
New Zealand
South Africa
Black & Decker
81 Hugo Johnson Drive
Penrose, Auckland, New Zealand
Tel. 09 579 7600
Fax 09 579 8200
Black & Decker South Africa (Pty) Ltd
Physical address:
Tel. (011) 653-1400
Fax (011) 653-1499
146 Lechwe Street
Corporate park
Randjiesfontein, Midrand
Postal address:
Postnet Suite 107, Private Bag X65
Halfway House 1685
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
498077-00
498077-00
|