OPERATOR MANUAL
IBEA VACUUM CLEANER TURBO 50
26. DO NOT try and regulate the rpm of the engine yourself. If
necessary, have the engine adjusted by your authorised IBEA
dealer.
28. At the time of manufacture the machine conformed to safety
standards. To assure optimum performance and continued safety,
use only original IBEA replacement parts.
27. Allow engine to cool before storing the machine in any enclo-
sed space, such as a garage or storage shed. Do not store it
where there is the possibility of flames or sparks setting alight any
residual fuel in the tank.
29. Perform only those maintenance instructions described in this
manual. If major repairs are ever needed or if assistance is desi-
red, contact an authorised IBEA service dealer.
ASSEMBLY
CONTROLS
Assembling the handle.
1. Additional plug
2. Height adjustment lever
3. Cable clamp
4. Zipper
5. Throttle lever
6. Bag coupling
7. Starter handle
1. Pull the grassbag over the chute door.
2. Pull the grassbag over the upper handle.
3. Secure the grassbag to its couplings on the handle.
STARTING
Working height adjustment.
Page 2
A. Filling with oil SAE 30 of high quality (SE, SF, SG) 0,6 l.
B. Filling with petrol. Use clean and fresh petrol.
A
B
3
On electric start models, just turn the ignition key to start the engi-
ne.
ATTENTION: When the engine is already warm it is not
necessary to press the pump in oder to start it. To
stop the engine, move the throttle to the “STOP” posi-
tion.
ATTENTION: Do not mix oil and gasoline. See engine
manual for further information on oil and fuel.
1. Move the throttle lever to the
position.
2. Press the pump three times to enrichen the carburetion.
3. Slowly pull the starter handle until the cord is stretched tight
and then pull hard to start the engine.
OPERATION
Keep people and animals away from the working area.
1
Always wear headset to protect your ears from excessive noise
during operation.
2
Page 3
Keep hands and feet away from the chute door and the rotor
under the deck.
Unzip the bag to dump the contents.
ATTENTION: Before unzipping the bag, make sure the
engine is off and the rotor has stopped.
MAINTENANCE
Clean the air filter every 25 hours. Replace it every season (see
engine manual for further information).
Throttle cable adjustment
With the throttle lever on start position, loosen the plate screw on
the engine. Move the cable until the throttle is closed and then
tighten the screw.
Operate only with grassbag in position.
ATTENTION: Make sure the engine is off and the plug
disconnected.
Page 4
VACUUM KIT 2010
BATTERIES MAINTENANCE
Assembling the kit
1. Remove the additional plug.
1. Store battery in dry and ventilated area disconnecting the bat-
tery from the wiring harness.
2. Insert the adapter into the mowerdeck.
3. Insert the hose into the adapter.
Storage temperature should not exceed 23¡ C.
4. Insert the vacuum spout into the hose.
5. Apply the tie strap to the lower part of mowerdeck.
2. Avoid storing discharged batteries. It is extremely important
that batteries are fully charged before storing.
3. If battery has discharged, it should be put immediately on
recharge. Required recharging time: 24 h.
4. Use only the charger supplied with the battery or one with fol-
lowing features: maximum current output 100-200 MA at 12 Volts
Nominal Voltage DC.
5. Before prolonged lawnmower storage, disconnect battery from
engine wiring harness and make sure battery is fully charged.
6. Avoid shorting battery terminals. The high current delivered by
batteries can overheat and damage the insulation and internal
connections.
Leave the unit on a level surface and shift the throttle lever to the
position.
Page 5
S.P.A.
Via A. De Gasperi 5
22070 Luisago (CO) - Italia
Tel. 031/92.91.50
Fax 031/92.94.07
|