VIP X1 XF E
VIP-X1XF-E
en Quick Installation Guide
VIP X1 XF E
Table of Contents | en
3
Table of Contents
1
2
3
Parts included
Unpacking
4
Installation
8
4.1
4.2
4.3
Mounting the frame
5
Connection
10
10
11
12
13
14
5.1
5.2
5.3
5.4
5.5
Connecting the camera and audio
Creating a serial connection
Alarm and relay connections
Establishing the network connection
Connecting the power supply
6
Assigning an IP address
15
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
F.01U.269.645 | V2 | 2012.06
4
en | About this Quick Installation Guide
VIP X1 XF E
1
About this Quick Installation Guide
This Quick Installation Guide applies to all variants of the
VIP X1 XF E.
WARNING!
You should always make yourself familiar with the required
safety measures (see Safety document enclosed).
Only operate the VIP X1 XF E in combination with an LPS/NEC
Class 2 power supply unit with limited output.
This Quick Installation Guide only describes the basic
procedure for installing a VIP X1 XF E and cannot replace the
complete manual.
For further detailed information, please see the extensive
online Help for the VIP X1 XF E.
This Quick Installation Guide, the Installation and Operating
Manual and the current firmware package are available in
F.01U.269.645 | V2 | 2012.06
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
VIP X1 XF E
Parts included | en
5
2
Parts included
–
–
–
–
–
–
–
–
1 VIP X1 XF E network video server
1 terminal block
4 self-adhesive elastic bumpers
1 wall-mounting panel
2 screws
2 wall plugs
1 Quick Installation Guide
1 Safety Hints
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
F.01U.269.645 | V2 | 2012.06
VIP X1 XF E
Installation | en
7
4
Installation
4.1
Preparing for wall-mounting
You can secure the VIP X1 XF E to any load-bearing wall using
the wall-mounting panel, in either a vertical or a horizontal
position.
CAUTION!
If mounting the unit in a vertical position, you will need to use
the lower plastic frame and then place the unit onto the frame
from above. If mounting the unit in a horizontal position, you
can use either of the two frames.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
F.01U.269.645 | V2 | 2012.06
8
en | Installation
VIP X1 XF E
4.2
Mounting the frame
CAUTION!
The mounting location must be able to reliably hold the unit.
The load-bearing capacity must be adequate for four times the
weight of the unit.
–
–
–
Lift the plastic frame on one side of the housing and
carefully remove it from the unit.
Screw the plastic frame in the required position together
with the wall-mounting panel.
Check that the plastic frame is secure.
F.01U.269.645 | V2 | 2012.06
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
VIP X1 XF E
Installation | en
9
4.3
Placing the unit in the frame
–
Place the unit on the wall-mounting panel, with the panel
positioned between the housing and the second plastic
frame.
–
–
Slide the unit into the plastic frame until you feel it lock
securely into place.
Finally, check that the unit is securely attached in the
installation location.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
F.01U.269.645 | V2 | 2012.06
10 en | Connection
VIP X1 XF E
5
Connection
5.1
Connecting the camera and audio
CAUTION!
Please observe the following specifications:
Line In: 9 kOhm typ., 5.5 Vp-p max.
Line Out: 16 Ohm min., 3 Vp-p max.
–
–
Connect the camera to the socket VIDEO IN.
Use the LINE IN/OUT socket for audio line connections.
F.01U.269.645 | V2 | 2012.06
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
VIP X1 XF E
Connection | en 11
5.2
Creating a serial connection
CTS
RXD
RTS
TXD
V I P X 1 X F
R
TXD
GND
12
V
D
C
GND
RT
LINK
S
AC
T
ETH
CAUTION!
Please observe the labeling on the orange socket of the
VIP X1 XF E.
–
–
If you require a serial connection to the VIP X1 XF E,
connect the relevant cables to the terminal block.
Connect the terminal block to the orange socket on the
VIP X1 XF E.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
F.01U.269.645 | V2 | 2012.06
12 en | Connection
VIP X1 XF E
5.3
Alarm and relay connections
Alarm In
IN
R
GND
R
V I P X 1 X F
R
TXD
GND
1
2
V
DC
GND
RT
LINK
S
AC
T
ETH
CAUTION!
Please observe the labeling on the orange socket of the
VIP X1 XF E.
Please observe the following specifications for the relay
contact: max. 30 V
(SELV), 200 mA
p-p
–
–
Connect the alarm switch to the appropriate terminals.
Connect the switch connection to the appropriate
terminals.
F.01U.269.645 | V2 | 2012.06
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
14 en | Connection
VIP X1 XF E
5.5
Connecting the power supply
V I P X 1 X F
R
TXD
GND
1
2
V
DC
GND
RT
LINK
S
AC
T
ETH
CAUTION!
Only operate the VIP X1 XF E in combination with an LPS/NEC
Class 2 power supply unit that has limited output and meets
the following specifications: 12 V output voltage, 0.30 A max.
–
–
Connect the power supply unit to the 12V DC socket. The
jack must fit a pin of 2 mm in diameter.
Insert the power supply unit plug into a suitable socket.
F.01U.269.645 | V2 | 2012.06
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
VIP X1 XF E
Assigning an IP address | en 15
6
Assigning an IP address
NOTICE!
Before you can operate the unit within your network, it must
have a valid IP address for your network and a compatible
subnet mask.
–
If you have not already done so, install the Video Client
program from the download area on our website.
Start Video Client.
–
–
Click
to start Configuration Manager. The system
automatically searches the network for compatible units.
When the unit is displayed in the list, Configuration
Wizard starts automatically. If not, select Configuration
Wizard... from the Tools menu.
–
–
Follow the instructions given in the Configuration Wizard
window.
Bosch Sicherheitssysteme GmbH
Quick Installation Guide
F.01U.269.645 | V2 | 2012.06
16 en | Assigning an IP address
VIP X1 XF E
F.01U.269.645 | V2 | 2012.06
Quick Installation Guide
Bosch Sicherheitssysteme GmbH
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
© Bosch Sicherheitssysteme GmbH, 2012
|