Bracketron Automobile Accessories MVM 45 05 User Manual

INSTALLATION MANUAL

FOR

VOLKSWAGEN - JETTA -1999.5-2005

VOLKSWAGEN - GOLF -1999.5-2006

VOLKSWAGEN - GTI - 1999.5-2005.5

Mount Location: To the right of the radio

MVM

Multi Vehicle Mount

MVM-45-05

Includes PHS-203 Ultra Slim Swivel

Thank you for purchasing your new Bracketron MVM Multi Vehicle Mount.

The Multi Vehicle Mount is an (end user-installer) modiﬁable professional mounting

bracket for most all mobile electronics requiring a steady and secure installation in a mo-

tor vehicle. The MVM installs behind your vehicles dash panel using existing or non-vis-

ible holes and is designed to cleanly protrude out from your vehicle’s dash panel.

Before installing, you must take the time to read and understand this installation manual

and read all the warnings accompanying this product.

Instructions Include: tools needed for install, directions for dash panel removal, directions

for modifying the MVM if required.

You can download this manual and any updates from

http://www.bracketron.com/downloads

MVM MODIFICATION INSTRUCTIONS

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

PLEASE NOTE

The Bracketron MVM-45-05 mount is a modiﬁable mounting bracket. The illustrations on the left show how this mount should

look during and after the modiﬁcation steps in order to ﬁt the listed vehicles on the front page of this manual. Many vehicle

applications may not require any modiﬁcations to the mount. If this is the case it will be noted below and there will be no steps

to follow on this page.

Before you begin to form your MVM, please make sure it looks exactly

the way it does in the top picture to the left.

Picture 1

To begin, use a marking pen to draw the lines on the MVM as

depicted in red in the middle picture to the left. Note: see red

lines in the middle picture for guidance.

Use a tin snips to cut along these lines. Then these cuts have been

made completely, continue by bending along the yellow lines as

depicted in the middle picture. Make this bend a 90° angle. If the

the bracket gets bent use a small hammer to pound out the imper-

fections. If the paint chips use some paint to cover up the paint.

Bend Mount Here

Picture 2

Now go back to Step 3 on the previous page to ﬁnish installa-

tion.

Cut Mount Here

Picture 3

Note: The hole pattern on the face of the MVM maybe

different then what is shown in the pictures.

Note: Please see page 3 in this manual for PHS-

203 Ultra Slim Swivel Instructions.

The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor

do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.

Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount. Bracketron Inc will not be liable

for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.

Bracketron Inc 5249 West 73rd Street, Suite G, Edina, MN 55439

tel: 952-746-7775 fax: 1-800-660-1784 toll free: 1-866-237-4443

email: [email protected] web: www.bracketron.com

PHS-203 ULTRA SLIM SWIVEL INSTRUCTIONS

PLEASE READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON MOBILE SOLUTION.

This Professional Swivel Mount Solution is designed to be mounted to your MVM or any other 4 hole AMPs compatible mounting

device. The Ultra Slim Swivel is compact with a low proﬁle and is designed to provide adjustability to devices such as Satellite

Radio Receivers, GPS monitors or Mobile Phones. The Ultra Slim Swivel angles your device for better viewing, tilting approx 15°

in all directions and swivels 360° degrees for maximum adjustability. All mounting hardware is included in the kit along with our

AMPs adapter plate to attach devices that support T- Notch mounting.

PARTS INCLUDED

1 - Ultra Slim Swivel

Note: The swivel can be installed before or after the mount is installed

in the vehicle. Attach the Ultra Slim Swivel to any MVM or CBM Mount or other AMPs

mounting device by inserting the M4x10 Pan Head screws through the holes on the

back half of the swivel. Align the screws up with the holes on the mount. Attach the M4

Nylon Locking Nuts only ﬁnger tight. Rotate the front half of the swivel to gain access to

the M4x10 Pan Head screws. (See Picture 1&2) Tighten all 4 screws with a #2 Phillips

screwdriver and 9/32” open end wrench.

1 - AMPs Adapter Plate

4 - M4 x 10 Hex Head

Screws

4 - M4 x 10 Pan Head Screws

4 - M4 x 12 Pan Head Screws

4 - M4 Hex Head Nuts

4 - M4 Nylon Locking Nuts

4 - M4 Star Washers

Picture 1

Picture 2

Picture 3

Rotate

Adjust Hold Tension

Picture 4

Tighten the center screw to adjust the desired tension of the swivel. (See

Picture 3) Note: If Swivel becomes loose over time, you can grasp the

swivel and pull toward you lightly while rotating it clockwise. This will

tighten the swivel allowing you to create the desired tension needed.

For T- Notch Devices

Attach the AMPs T- Notch Adapter to the front half of the swivel

using the M4x12 Pan Head screws. Attach the M4 Star Washers and

M4 Hex Nuts to the screws and tighten the plate down with the #2

screwdriver and 9/32” open end wrench. Slide your device onto the

T- notch Adapter plate to secure it to the swivel. (See Pictures 4)

Picture 5

For AMPs Devices with Inserts

Attach your AMPs device using the M4x10 Hex Head screws and M4

Star Washers. Align the holes on the device with the holes on the front

half of the swivel. Slide the Star Washers onto the Hex Head screws.

Insert the screws through the swivel and into your device only ﬁnger

tight. Tighten down the device with the 9/32” open end wrench.

Your device is now secure to the swivel. (See Pictures 5)