DSP-5
Brady Worldwide Identification Solutions
6555 West Good Hope Road
P.O. Box 2131
Milwaukee, WI 53201-2131
Phone: (800) 537-8791
Fax: (800) 292-2289
05/01
SET-UP INSTRUCTIONS
ADJUSTMENTS
Hold Down Brush:
Using 5/32" (4mm) hex wrench, adjust reel holder arm to vertical.
Using the upper thumbscrew on the side of the machine, adjust the hold down brush for
tensioning.
Place the label roll on the 1" (25mm) reel hanger bar.
*If roll has 3" (76.2mm) core, use plastic spool*
Slide “O” ring onto reel hanger bar to hold roll against reel holder arm to ensure it is
held straight.
For best results, labels should be pressed firmly against the strip plate. If labels are held
too tightly, they will cause excessive drag on the motor.
Photosensor:
(Hex wrench, O-ring and spool included.)
The photosensor can be adjusted in any direction to accommodate virtually any label.
Loosening the lower thumbscrew allows the photosensor to swivel and sets the overhang
distance of the label over the strip plate. When the label is being fed the correct
distance, tighten the lower thumbscrew.
Thread the liner under the guide rod, between the hold down brush and the strip plate,
then back under the strip plate. Lay the liner across the slot in the take-up hub. Slide the
lock rod into the slot to secure the liner. Align shaft collar on guide rod with edge of
liner to keep material feeding straight.
Loosen the two screws on the front of the sensor holder to align the photosensor with
the center of the label. If there are two or more labels across, align the photosensor
with the last label to be removed. When these two screws are tightened, the machine
is set.
Reel Holder Arm
Positioning of Photosensor
Incorrect
Hold Down Brush
Guide Rod
Lock Rod
Reel Hanger Bar
Sensor sees beyond label
- Will not stop
Sensor sees strip plate
- Will not feed
Strip Plate
Correct
Photosensor
Take-up Hub
Sensor sees front edge of label
4
5
FEATURES
MAINTENANCE
• Will dispense butt-cut and die-cut material.
• Adjustable photosensor for pinpoint accuracy.
• Handled lock rod makes scrap removal easy.
• No tools required for adjustment.
Turn machine off when not in use. Remove liner material from take-up hub at
approximately 3" in diameter or if motor appears to be straining. Do not operate
machine without covers in place. Do not operate if inspection reveals a damaged
power or sensor cord.
LEGEND
Model DSP-5
NOTES
• Keep strip plate free of adhesive build-up.
• Clean photosensor with compressed air or dry cloth.
• Do not drop the dispenser or subject it to heavy shock.
• Turn off machine when not in use.
Item #
Part #
1
NV50008
1A
1B
2
NV50008-1
NV50008-2
NV50010
2A
2B
3
NV50010-1
NV50010-2
NV50017
REPAIR POLICY
Contact BRADY CORPORATION to determine nature of problem.
3A
4
NV50017-1
NV50017-2
NV-SPOOL
Furnish Brady with the following information:
1. Who the unit was purchased from.
2. Model number and serial number.
3. Date purchased (copy of invoice or packing slip required).
5
6
NV50001A (115V)
NV50001C (220V)
NV50001-1
NV50018-2
NV50013A
6A
6B
7
Brady will issue an RGA (Return Goods Authorization) for repair.
Return machine to Brady by UPS, insured and prepaid.
Brady will notify the customer if there is a repair charge.
8
NV50012
8A
9
NV50012-1
NV50014-1
NV50014-3
NV50014
9A
10
10A
NV50017-1
SPECIFICATIONS:
11
NV50026B
NV50011-2
NV50026-1
NV50026A
NV50015
NV50017-1
NV50015A
NV50011A
NV50002A
NV50011
11A
11B
12
Model#
DSP-5
Liner Capacity
Width
.25" to 4.5"
13
(6.35mm to 115mm)
13A
13B
14
Label
.125" to 7"
Length
(3.2mm to 178mm)
15
16
Roll Capacity
Feed Speed
12" (30.5mm)
16A
16B
17
NV50011-2
NV50011-1
NV50007
1.3" / sec*
(3.3mm / sec.)
18
NV50003
19
NV50009
Dimensions
Inches
19A
20
NV50007-1
NV50021 (115V)
NV50021A (220V)
NV50005-1
NV50021-1
NV50019
10.8 (L) x 10.8 (W) x 14.5 (H)
Centimeters 27.4 (L) x 27.4 (W) x 36.8 (H)
20A
20B
21
Weight
10.5 lb. (4.76 kg.)
Electrical
117V 50/60Hz, <1 amp
(220V 50/60Hz available)
21A
22
NV50019F
NV50018C
NV50005
NV50005-1
NV50021-1
Requirements
23
*at start-up
23A
23B
6
3
|