Bushnell Binoculars 118326 User Manual

Digital Camera binoCular  
Version 2.0  
User Manual  
Model#: 118326  
Lit. #: 98-0917/02-10  
 
QUICK START GUIDE: BUSHNELL SYNCFOCUS™ INSTANT REPLAY  
1) The SyncFocus is powered by two AAA batteries (not included). Insert batteries into the compartment (G), using the polarity  
marks inside for reference. A power meter in the lower left corner of the display indicates battery condition.  
2) Insert an SD or SDHC card into slot (J) if greater storage is desired. The card will click into place. You may use SD/SDHC cards  
(not MMC cards) up to 32 GB capacity. If the card you insert was previously used in other devices, format it before taking  
photos. Press the Enter button (D) to enter Play mode, then press the MENU button (C). Press the Minus key (D) once to select  
“Format, then press Enter. Note the warning that this will erase all files-make sure you have backed up any files you wanted  
to keep. Press the Plus key (D) to select “OK, then press Enter to format the card. Press Enter again to exit the Play mode.  
3) Raise the LCD display (A), and press the ON/OFF button (B) briefly. The camera will automatically turn itself off after two  
minutes of inactivity (this can be changed using the “Auto Offoption in the Setup menu).  
4) To set the menu language, press the MENU button. Keep pressing the Plus or Minus key until you highlight “Language,  
press Enter, then press Plus to highlight your language and press Enter.  
The Date/Time imprint feature is turned on by default. Press the Plus key to highlight “Clock Set” and press Enter. Now set  
the Year, Month, Date, Hour and Minute (in order from left to right), using the Plus/Minus keys to make changes, and the  
Right key to move to the next item. Once date & time are set, press the Enter button. UseDate Stampto set your preference  
(month first, year first or o) Press Enter then Exit the menu to return to the preview display. Reset the date/time if you replace  
batteries.  
5) Turn the reticle focus (E) until the black circle is sharp, then adjust the binocular focus (K) until your subject is sharp. Hold the  
camera steady with both hands and press the SNAP button (L) to take a still photo. When using a tripod, you can help avoid  
the effects of camera shake by plugging the supplied remote shutter release cable into the jack next to the SD card slot rather  
than SNAP to take photos.  
6) To shoot a video, press the Right key (D) three times until the red movie camera icon appears at the top right corner of the  
display (see “LCD Preview Display Icons”-#10). You can then start shooting the video at any time by pressing the SNAP button.  
 
3
QUICK START GUIDE: BUSHNELL SYNCFOCUS™ INSTANT REPLAY  
To stop recording the video, press the SNAP button again. By default, videos are recorded as a 15 second loop (“instant  
replay”). To change this, press MENU-the first item is “Resolution. Press Enter, then select “Video Size. Use the Plus/Minus  
keys to select a different video resolution and frame rate combination (which determines loop length-8, 15, 30 or 60 seconds).  
You also have the option to select a “Norm” video setting if you prefer to shoot standard video clips, instead of loops that re-  
record (refresh) automatically. For more information regarding the still and video resolution options and other menu  
settings, please see the “Using the Main Menu” section of this manual.  
7) To review or playback a still photo or video, press the Enter button. You will see the most recent still photo or video. To  
review previous photos or videos one at a time, press the Left key. To play back a video, press the SNAP button (press again  
to stop playback). To delete photos/videos, press MENU. Select Delete One (only the currently displayed photo/video) by  
pressing Enter, then the Plus button to select “OK, and press Enter to delete the file. If you wish to delete all photos/videos,  
use the Format menu option as described earlier.  
8) To download photos/videos to your PC, connect the USB cable from the SyncFocus to your computer. The SyncFocus will  
be recognized as a standard “USB Mass Storage” device and will appear as a “Removable Disk” under the “My Computer” list  
(on Macs, an icon will appear on your desktop). The photo files are located in theDCIMfolder on thisRemovable Disk. Copy  
the files to your hard drive (drag or use the “copy files” option), then disconnect the camera. (On Mac computers, drag the  
“diskthat appeared on your desktop when the camera was connected into your Trash toejectit before disconnecting.) The  
jpg standard files from the SyncFocus may be edited with any photo software you choose to use.  
NOTE: If you are not using an SD card in the SyncFocus, be sure to download all files from its internal memory before changing batteries  
and before storing the camera for a long period. If you use an SD card, photos may also be downloaded by removing the card and using  
any USB card reader with an SD slot.  
Your SyncFocus camera is already set for high resolution and quality right out of the box, and it is not necessary to  
change any of the settings to get good results. However, many features and options are provided to enhance your  
enjoyment of the camera. For more information about them, please refer to the remainder of this User Manual.  
 
4
BASIC SETUP  
Loading Batteries  
Turn the SyncFocus over, slide open the battery cover as indicated by the arrow, remove and set aside. Insert 2  
AAA Alkaline or Lithium batteries into the compartment (G) in the direction indicated inside, then replace the  
cover, sliding it back into place until it clicks. Note: Rechargeable NiMh type batteries may also be used, but  
some may not deliver adequate current to power the camera and display. AAA NiMh batteries with a current  
rating of 850 mAh or higher are recommended.  
Inserting An SD Card  
The camera can store from about 15 (at 2660x1920 resolution andBestquality) up to over 100 photos in the  
internal memory, depending on resolution and quality settings. To expand the available storage, you may  
add an optional SD or SDHC (High Capacity) memory card, with 32GB or lower capacity. The camera will  
not function if a 64GB or higher capacity SD card is inserted. Do not use “MMC” cards, which look similar to  
SD cards. The card is inserted into the slot (J) on the back of the camera pod (pull down the rubber cover flap-  
please refer to the “Camera and Binocular Parts Guide” page), label side up with the “notched” corner on the  
right as indicated by the card icon above the slot. Note: be sure the power is turned off before inserting or  
removing cards to prevent possible loss of files or damage to the card. A new card will not require formatting,  
but a card that has been previously used in other devices (cameras, mp3 players, etc) should be formatted by  
the SyncFocus before you start taking photos (see the “Using the Review Menu” section for details). Note that  
formatting will erase all files previously stored on the card, so be sure they have been downloaded and  
saved on your computer first if you wish to keep them.  
 
5
BASIC SETUP  
Setting the Date and Time/Date Stamp Feature  
You may want to go into the main options menu and set the correct date and time before beginning to take  
photos (or turn off the date stamp feature, as the default setting is “on”). To set date and time:  
1.  
2.  
3.  
Raise the LCD display and press the ON/OFF (B) button.  
Press MENU (C). Press the Minus key (D) 7 times to highlight “Clock Set, and press the Enter button (D).  
Now set the Year, Month, Date, Hour (24 hr format), and Minute, using the Plus/Minus keys to make  
changes, and the Right key (D) to move to the next field.  
4.  
5.  
Once the date & time are set, press the Enter button.  
Press the Minus arrow key once to highlight “Date Stamp, press Enter, then highlight your preference  
using the Plus/Minus keys: Month-Day-Year format, Year-Month-Day format, or OFF (the date will not be  
stamped on your photos).  
6.  
Press Enter, then press the Minus key twice to highlight “Exit” , then press Enter again to exit the menu  
options and return to the “livepreview display.  
Auto Off (Power Save)  
By default, the SyncFocus will automatically turn off if no buttons or controls have been pressed for two  
minutes. This helps save power and extend battery life when the camera is accidently left on. However, when  
you are first learning to use the camera you may want power to remain on (until you press ON/OFF) as you  
get familiar with the features and controls. To do this, enter the main menu as described above in “Setting  
the Date...”, highlight “Auto Off, press Enter, and select “Cancel. Press Enter, then exit the menu as described  
above.  
 
6
Menu Display Language Options (English, Spanish, Italian, French, German)  
The main menu also has an option to select your preferred language for all menu screens.  
SYNCFOCUS SETUP (Reticle & Diopter)  
Setting the Reticle Focus and Diopter Adjustment  
Before you begin taking photos, a few simple, one-time adjustments should be made to ensure that you  
can get sharp photos of any subject by just using the main focus knob on the binoculars. This process will  
compensate for any variations in the eyesight or vision of the individual user:  
1.  
Leave the rubber eyecups in their “up” position if you are not wearing glasses, or roll them down if you  
are. Grasp the left and right sides of the binocular, and pull them apart or push them together while  
looking through the binocular to adjust the eyepiece spacing until your view is a single circular image.  
Look through just the left side of the binocular-you will see a black ring (reticle) in the center. Point the  
binocular at a plain, light background like the sky or a wall in your house.  
Rotate the reticle focus (left eyecup-(E)) until the circular reticle appears as sharp as possible to your left  
eye. This compensates for any difference in between your vision and the correct focus for the camera.  
Next, continuing to look through the left side only, aim at a distant object (preferably one containing  
fine detail such as a tree or sign), and adjust the binocular’s center focusing knob (K) until it appears as  
sharp as possible to your left eye.  
2.  
3.  
4.  
5.  
Finally, view the same object through only the right side of the binocular, and rotate the diopter  
adjustment (right eyecup-(F)) until it appears sharp to your right eye (do not touch the center focus knob  
while doing this). This compensates for any vision differences between your left and right eyes.  
 
7
SYNCFOCUS SETUP (Reticle & Diopter)  
Once set, note the number on the left and right binocular tubes that the index mark on each eyecup is lined  
up with. With the reticle focus and diopter adjustment set to these positions, you should be able to get sharp  
photos/videos of a subject at any distance by simply adjusting the center focus knob while you look through  
the binocular optics. There is no need to re-adjust the reticle focus or diopter adjustment, unless you share the  
Syncfocus with another user, or if your eyes become tired over a long period of use.  
The camera lens provides 8x magnification, which is the same power as the binocular’s optics, and it is aligned  
so that an object centered in the binocular will also be centered in your photos or videos. Therefore, it is not  
necessary to have the LCD turned on or even raised while you are shooting photos or videos. Reducing use of  
the LCD will extend battery life significantly.  
 
8
TAKING STILL PHOTOS  
After completing the basic and Syncfocus setups as described in the previous pages, you are ready to take a  
photo:  
1.  
2.  
Raise the LCD display (A) and briefly press and release the ON/OFF button-the startup screen will appear,  
followed by the live image from the camera lens. The display also shows the battery condition, number  
of photos remaining, and the current setting of various options. Please refer to “LCD Preview Display Icons”  
for more details.  
The SyncFocus will default to high resolution and quality settings, as well as “everything on automatic”  
when it is turned on for the first time, so you’re ready to take photos under most conditions with no need  
to change anything. If you’d like to explore the various available options, see the manual section titled  
“Using the Main Menu-Options and Settingsfor directions regarding how to select and change settings  
such as resolution, image quality and exposure.  
3.  
4.  
You may compose your photo while looking through the binocular (the LCD does not need to be  
on to take a photo). However, for the most accurate framing, checking the LCD preview display is  
recommended.  
Hold the camera as steady as possible with both hands and gently press the SNAP button. If possible,  
attach the SyncFocus to a tripod and plug the supplied remote shutter cable into the remote jack (H) to  
obtain the steadiest results (press the button on the remote to take a photo). The display will “freeze”  
briefly immediately after a photo is taken-this is normal while the image is being stored in the internal  
or card memory.  
 
9
TAKING STILL PHOTOS  
5.  
Theremaining photos4-digit counter in the lower left corner of the display above the battery indicator  
will drop by one number after each photo (or two, depending on your subject and settings) is taken.  
Once it reaches “0000, and the display indicates “Memory Full !” when SNAP is pressed, you are out of  
memory (storage space) and will need to download the photos you have taken so they can be deleted  
to make room in the memory for new photos, or you may remove the filled up card and install another  
SD card if you are on a trip away from your computer.  
6.  
7.  
A digital zoom feature is available. Press the Plus arrow key to zoom in (you will see the result on the  
LCD, and the digital zoom indicator bar moves towards“T”for“Telephoto”). Press the Minus arrow key to  
zoom back out (the zoom indicator bar moves towardsWforWide Angle”). To turn off all digital zoom  
(go back to the 8x optical magnification only) keep pressing the Minus key until the zoom bar indicator  
goes back fully left to “Wand disappears.  
To review a photo after you take it, press the Enter button. To see previous photos, press the Left arrow  
key-each press takes you back one photo, and pressing the Right arrow key moves forward to more  
recent photos. Press the Enter button again to return to the live preview. See the sectionReview Menu”  
for directions covering deleting photos, formatting internal or card memory, and protecting important  
photos.  
NOTE: Use care during handling to avoid touching the camera lens (M), located in the center between the  
binocular lenses, to prevent degrading the image quality. Clean the camera lens only with dry lens tissue or  
microfiber cloth. DO NOT use liquids of any type.  
 
10  
SHOOTING VIDEOS (SETTING/USING VIDEO MODE)  
To switch from still photo to video mode, press the Right arrow key 3 times, until the red movie camera icon  
is displayed at the top right area of the LCD (seeLCD Preview Display Icons, #10). You are now in Video Mode.  
Press SNAP to start recording a new video clip, and press it again to stop recording and store the video in  
memory. The recording time is limited only by the amount of internal or card memory currently available.  
You may record a single long video until you run out of memory or multiple shorter videos by stopping and  
starting recording whenever you wish by pressing SNAP. The counter on the right side of the display shows  
the time elapsed since the recording was started. Note: the video files use the .avi format.  
By default, videos are recorded as a 15 second loop (“instant replay”). To change this, press MENU-the first  
item is “Resolution. Press Enter, then select “Video Size. Use the Plus/Minus keys to select a different video  
resolution and frame rate combination (which determines loop length-8, 15, 30 or 60 seconds). You also have  
the option to select a “Norm” video setting if you prefer to shoot standard video clips, instead of loops that  
re-record (refresh) automatically. For more information regarding the still and video resolution options and other  
menu settings, please see the “Using the Main Menu” section of this manual.  
Press the Enter button if you wish to check a video after you shoot it. Press the SNAP button to begin playback,  
press it again to pause playback (the display will indicate “AVI PAUSE”). During playback, the counter on the  
right displays time remaining in the video clip. Press the Left arrow key to review previous video or still photo  
files. When you are ready to return to the live preview display to shoot more videos (or stills), press the Enter  
button.  
 
11  
LCD Preview Display Icons  
4
5
Still Photo  
Preview Display  
#
1
2
Icon  
6
7
Battery Indicator (full battery shown)  
# of Photos Remaining (based on unused internal  
or card memory)  
3
2
11  
3
4
Internal or Card Memory  
1
White Balance Setting (Auto White Balance  
shown)  
Additional Feature Icons  
Press the Right key (1, 2, or 3 times) to  
select the self timer, rapid sequence, or  
video mode features. Press once again  
after selecting video mode to return to  
normal still photo operation (camera icon  
returns at top right of LCD).  
9
5
Exposure Meter Pattern setting  
Photo Resolution setting (Pixels)  
Photo Quality setting (File Compression)  
Self Timer (10 sec delay)  
6
7
8
9
Rapid Sequence (3 shot burst)  
10  
8
10  
Video Mode (Elapsed time counter as shown is  
visible only during recording)  
11  
Digital zoom indicator bar (only visible when  
digital zoom is in use)  
 
12  
Using the Main Menu-Options and Settings  
As mentioned earlier in this manual, your SyncFocus is already set for high resolution and quality right out  
of the box. Exposure, white balance, and other variables are set automatically. This means that you will get  
good results for most subjects and lighting without the need to go into the menu to change any settings.  
However, you should become familiar with the available options so that you can improve your photos if, for  
example, you decide they are coming out too dark (common in photos with snow or at the beach), or too  
green (under some fluorescent lights). Press the MENU button to enter the main menu. Use the Plus/Minus  
keys to highlight an option within the menu, then press Enter if you wish to change the settings for that  
option. Use the Plus/Minus keys to select the setting you want, then press Enter to confirm this setting. Here  
are all the options and settings available in the main menu, along with descriptions of what they do:  
OPTION  
SETTINGS  
DESCRIPTION  
Resolution  
(Image Size) 2660x1920 (4.9MP),  
3264x2440 (7.9MP*),  
Sets the desired still photo resolution in pixels (megapixels).  
Higher resolution settings produce sharper/larger prints  
but require more storage space in internal or card memory.  
2048x1536 (3.1MP),  
1600x1200 (1.9MP), 800x600 Use lower settings to store more in memory, or for email, PC  
(0.48MP)  
viewing only, etc.  
*7.9MP via software interpolation.  
Actual sensor resolution is 4.9MP.  
Note: Default settings are indicated in bold  
 
13  
Using the Main Menu-Options and Settings  
OPTION  
SETTINGS  
DESCRIPTION  
Resolution  
640x480 30F Loop, 640x480  
“640x480”or“320x240”=resolution in pixels per video frame.  
Higher resolution=more detail. “30F” or “15F”=frame rate  
in frames per second. Faster FPS=smoother video. “Loop”  
or “Norm”=use a Loop setting if you want “Instant Replay”  
video (automatically starts recording again after 8, 15, 30 or  
60 seconds, erasing the previous video). Use “Norm” for a  
“normalcontinuous video, with recording time limited only  
by available memory (no automatic re-recording).  
(Video Size) 30F Norm, 640x480 15F  
Loop, 640x480 15F Norm,  
320x240 30F Loop, 320x240  
30F Norm, 320x240 15F  
Loop, 320x240 15F Norm  
Image  
Quality  
Best, Better ,Standard  
Sets the amount of file compression, which affects the  
quality of the photo and the size of the file it creates. This  
can be used independently of Image Size to help store  
more photos in exchange for slightly reduced quality. “Best”  
produces the highest quality, but also generates larger files  
that fill available memory sooner (fewer photos possible).  
EV  
-2.0 ~ +2.0 (Default= 0 EV)  
Provides manual under/over exposure adjustment in 0.5  
EV steps. Minus values produce darker photos, plus values  
lighter. When a subject is mostly bright (snow scene), you  
may need to add some “+EV to avoid underexposure.  
 
14  
Using the Main Menu-Options and Settings  
OPTION  
SETTINGS  
DESCRIPTION  
White  
Balance  
Auto, Daylight, Cloudy,  
Fluorescent, Tungsten  
Sets the reference for neutral white, so that colors are  
reproduced correctly. If “Auto” does not provide good  
results, try the setting that matches the light source.  
Meter  
Weight, Center, Average  
Sets what area of the image frame is used to determine  
exposure. “Weightbases the exposure 60% on the center  
of the frame, 40% on the rest of the frame. “Centeruses  
only the center area (good for strong backlit situations),  
and “Averageaverages exposure for the entire frame.  
Language  
Auto Off  
English, Spanish, Italian,  
French, German  
Selects preferred language for all menu display screens.  
60 S (1 min), 120 S (2 min),  
Cancel  
Sets the interval after the last action (pressing any button)  
before the camera turns off to conserve battery power.  
Select “Cancelto prevent auto shutoff altogether.  
Clock Set  
Sets:  
Use the Plus/Minus keys to set (in order) the Year, Month,  
Date, and Hour, Minute, Second. Use the Right key to move  
to the next field you want to set. See “Date Stamp” also.  
YEAR/MONTH/DATE/  
HOUR/MINUTE  
 
15  
Using the Main Menu-Options and Settings  
OPTION SETTINGS DESCRIPTION  
Date Stamp MM/DD/YY, YY/MM/DD, OFF Use the first two settings if you want the date and time  
imprinted in the lower right corner of all your photos-you  
have the option of month first or year first formats. The  
time will also be included-only 24 hr format is available. To  
prevent imprinting the date and time, highlight “Offand  
press Enter.  
Default  
Setup  
OK, Cancel  
Restores all settings for all options to original factory  
default settings.  
Exit  
Select “Exitand press Enter to exit the Menu and return to  
the preview (“livecamera) display.  
Using the Review Menu-Options and Settings  
Press Enter to enter Review mode. Use the Left arrow key to go back through the stored photos/videos. Once  
you are in review mode, pressing the MENU button will enter the review menu. This operates in the same way  
previously described in the main menu system instructions (use the Plus/Minus and Up/Down arrow keys to  
navigate to the desired menu option and settings, press Enter to confirm a setting), but with different menu  
items as shown in the following table:  
 
16  
OPTION  
SETTINGS  
DESCRIPTION  
Delete One OK, Cancel  
Highlight “OK” and press Enter to delete the currently displayed  
photo or video. If pressed accidently, highlight “CANCELand  
press Enter.  
Format  
OK, Cancel  
Same as above except deletes entire contents of internal or  
card memory. When an SD card is inserted that has been used  
previously in other devices, formatting it before starting to  
take photos is recommended (be sure any files you want to  
keep have been downloaded and backed up first). Can also be  
used anytime to quickly delete all photos instead of one at a  
time. When all photos have been deleted, the display will show  
“Sorry-no picture.  
Protect  
Lock, Unlock  
Highlight “Lockand press Enter to protect the currently dis-  
played photo or video from accidental erasure (unless Format is  
used to delete entire contents of memory). Highlight “Unlock”  
and press Enter to allow deleting a previously protected photo  
or video.  
The Review Menu Options after “Protect” (Language, Auto Off, etc.) are the same as those  
after “Meter” in the Main Menu, and perform the same functions as previously described  
in “Using the Main Menu.  
 
17  
TRANSFERRING THE PHOTOS & VIDEOS TO YOUR PC  
1. Turn on the SyncFocus (press ON/OFF). Connect the supplied cable to the USB port (I) below the SD card slot  
on the SyncFocus (pull down the rubber cover flap-please refer to the “Camera and Binocular Parts Guide” page),  
then connect the other end directly to a main USB port on your computer-do not use front panel/keyboard  
USB ports or unpowered “hubs.  
2. The LCD display will indicate “MASS STORAGE, and the ImageView will be recognized as a standard “USB  
Mass Storage” device. This means that the camera files can be easily viewed, edited, or copied to your hard  
drive, just as if they were stored on an external hard drive or a CD-ROM.  
3. (This step is not required with Windows XP, simply use the options in the pop-up window to view, copy or  
edit your photos). Open My Computer or Windows Explorer. The camera will be seen as a new “Removable  
Disk” with an unused drive letter assigned to it. Double click this new “Disk” icon, open the “DCIM” folder  
inside, then the folder(s) inside that (“100MEDIA” ,etc). Your photos/videos are the files inside-they have the  
prefix “PICT__” followed by a number, same as seen earlier on the camera’s display when you review photos.  
Double click a file to view it full screen, or select the “Filmstrip” or “Thumbnail” options from the View menu  
of the open window.  
4. Click “Edit>Select All” in the Windows menu (or click on one photo, contol+click to select multiple photos),  
then “Edit>Copy to Folder” (in Windows menus). Select an existing folder on your hard drive, such as “My  
Pictures, or create a new folder (“Hawaii Vacation, etc), then click “OK” to transfer copies of the photo files  
you want.  
 
18  
5. After the photos are transferred to your computer, you can disconnect the SyncFocus. Windows 2000 may  
produce a screen warning that you have disconnected a USB device without stopping or ejecting the “disk”  
first (your photo files will not be harmed). If so, check the box that adds an icon to your system tray or taskbar.  
Then next time you finish transferring photos, you can click that icon first, and “Stop the USB Mass Storage  
Device” before disconnecting the camera. (On Mac computers, you should “eject” the “disk” that appeared on  
your desktop when the camera was connected-you can simply drag it to the Trash to eject it.)  
Note: If your PC will not play the .avi movie files in Windows Media Player, you may need to download a newer  
version of Media Player or Direct X from Microsoft.com. The movie files can also be played back with the  
QuickTime Player, included with many computers, or available as a free download from Apple.com.  
6. You’re now ready to open the photo files in any photo editing software. Just use File>Open and go to the  
folder where you stored the photos earlier. It is also possible to open and work with your photos directly from  
the ImageView while it is still connected. If you choose to work this way, from a connected camera, be sure  
that you save the photo (when you are done editing) to your hard drive, and not the camera’s memory or  
card.  
7. If you are new to photo editing on a computer, consult your software’s Help menu or manual for tips on  
using its features. Along with adjusting the brightness, contrast, sharpness and color of your photos, you can  
resize the photo to fit the paper if you are printing, or save a smaller, low or medium resolution version for  
email or inserting into documents. When you are ready to save your edited file, you may want to useSave As”  
and give it a more descriptive name than “PICT___. Doing this also preserves the original file as a backup to  
reopen and re-edit later. Make sure you have successfully transferred all the photos you wanted to save before  
using “Formaton your camera to make room for new images.  
 
19  
TWO-Year LIMITeD WarraNTY  
FCC Compliance Statement:  
Your Bushnell® product is warranted to be free of defects in materials and workmanship for two years after the date of  
purchase. In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that  
you return the product postage prepaid. This warranty does not cover damages caused by misuse, improper handling,  
installation, or maintenance provided by someone other than a Bushnell Authorized Service Department.  
is equipment has been tested and found to comply with the limits  
for a Class B digital device, pursuant to part 15 of the FCC Rules.  
ese limits are designed to provide reasonable protection against  
harmful interference in a residential installation.  
Operation is subject to the following two conditions: (1) is device  
may not cause harmful interference, and (2) this device must accept  
any interference received, including interference that may cause  
undesired operation.  
Any return made under this warranty must be accompanied by the items listed below:  
1) A check/money order in the amount of $10.00 to cover the cost of postage and handling  
2) Name and address for product return  
is equipment generates, uses and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
3) An explanation of the defect  
4) Proof of Date Purchased  
5) Product should be well packed in a sturdy outside shipping carton, to prevent  
damage in transit, with return postage prepaid to the address listed below:  
IN U.S.a. Send To:  
Bushnell Outdoor Products  
Attn.: Repairs  
8500 Marshall Drive  
Lenexa, Kansas 66214  
IN CaNaDa Send To:  
Bushnell Outdoor Products  
Attn.: Repairs  
25A East Pearce Street, Unit 1  
Richmond Hill, Ontario L4B 2M9  
· Reorient or relocate the receiving antenna.  
· Increase the separation between the equipment and receiver.  
· Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
For products purchased outside the United States or Canada please contact your local dealer for applicable warranty  
information. In Europe you may also contact Bushnell at:  
Bushnell Germany GmbH  
European Service Centre  
Mathias-Brüggen-Str. 80  
D-50827 Köln  
· Consult the dealer or an experienced radio/TV technician for help.  
e device does not contain any user-serviceable parts. Repairs should  
only be made by an Authorized Bushnell repair center. Unauthorized  
repairs or modifications could result in permanent damage to the  
equipment, and will void your warranty and your authority to operate  
this device under Part 15 regulations.  
GERMANY  
Tel: +49 221 995568-0  
Fax: +49 221 995568-20  
e shielded interface cable which is provided must be used with  
the equipment in order to comply with the limits for a digital device  
pursuant to Subpart B of Part 15 of FCC Rules.  
This warranty gives you specific legal rights.  
You may have other rights which vary from country to country.  
©2010 Bushnell Outdoor Products  
Windows is a registered trademDarkoofwMincrolosoaft Cdorpfrooratmion iWn thwe Uwnit.eSd Sotatmes aannd outhaerlcso.ucntoriems. . All SMpecaicnatiuonsaanldsdesSignes aare srucbjehct toAchnangde wDithooutwanynnoltoiceaordobl.igation on the part of the manufacturer.  
Mac and Mac OS are trademarks of Apple Inc., registered in the U.S. and other countries.  
INNOVATION THAT THRIVES OUTSIDE  
For further questions or additional information please contact:  
Bushnell Outdoor Products  
9200 Cody, Overland Park, Kansas 66214  
(800) 423-3537 • www.bushnell.com  
©2010 Bushnell Outdoor Products  
 

Blanco Indoor Furnishings 157 160 User Manual
Blodgett Convection Oven BC14E User Manual
BMW Automobile Z3 User Manual
Bosch Appliances Ventilation Hood DKE 93 User Manual
Canon Digital Camera 3000 QD User Manual
Casio Electronic Keyboard LK300AR1A User Manual
Casio Electronic Keyboard SA 77 User Manual
Casio Watch 1803 User Manual
Centurion Oxygen Equipment CP72SR5 User Manual
Chatsworth Products Network Card RIM 600 User Manual