FWV470
Manual for Installation, Use and Maintenance
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
Icemaker
Display
Control Panel
Water Nozzle
Ice Drawer
Ice Water Tray
Drip Tray
Icemaker control panel
ON OFF
1
2
3
4
5
6
1. On button
2. Off button
3. Water glass button – this button dispenses a small amount of water.
4. Water jug button – this button dispenses a large amount of water.
5. Manual water button – this button dispenses water as long as the button is pressed.
6. Settings button – this button changes the preset amounts of water.
2
The Icemaker
Before first use:
1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you.
2. Turn on the machine at the power switch on the left side of the machine The machine will automatically start a drain
cycle, which will take approximately five minutes. During this process, the display will show ICE OFF WATER EMPTY.
3. Push the machine back into the housing.
4. Switch on the machine by pressing the
button.
5
The machine is now ready for use and the display shows ICE ON WATER READY.
Please note
You should clean the pipes through before first use to remove any impurities in the system after installation. To do so,
place a jug under the water nozzle and press for approximately two minutes, disposing of the water dispensed.
3
The Icemaker
To make ice
The icemaker will make ice automatically once it is switched on and will continue to make ice until the ice compartment is
full. Whenever ice is removed, the icemaker will make more ice until the compartment is full again.
To dispense water
The amount of water dispensed from the water nozzle is controlled by three different buttons.
– water glass
– water jug
– manual setting – this button dispenses water as long as the button is pressed.
To change the preset buttons
It is possible to adjust the amount of water dispensed by the preset buttons (
the water nozzle and press until the required amount has been dispensed. Then confirm the setting by pressing buttons
for the water glass button or buttons for the water jug button.
&
). To do so, place a glass or jug under
&
&
Please note:
To stop water dispensing once a preset button has been pressed, simply press the button again.
The ice water tray is located below the ice drawer. In normal use this fills with water, this does not constitute a fault. This
water is used in the ice making process and is replaced every 24 hours by the automatic drain cycle. You should use the
water from the water nozzle for drinking.
The water nozzle is height adjustable for ease of use. To adjust the height, hold the black outer section of the water nozzle
and raise or lower it to the height required. The nozzle will automatically remain at the height set.
To dispense ice
When the ice drawer is full, the display shows ICE FULL WATER READY.
Open the drawer fully and use the scoop provided to remove the ice as required.
Please note:
If the ice drawer is not emptied for a long period of time, the appliance will go on standby for approximately ten minutes,
and the display shows ICE OFF WATER READY. After the standby period has ended, the appliance will begin to make ice
again. If you do not want to wait for the standby period to finish, press the
button.
If the ice drawer is not emptied regularly an excessive accumulation of ice cubes could hinder the movement of the upper
carriage. You are recommended to open the ice drawer slowly after a long period of time on standby and regularly remove
ice cubes from the drawer.
4
Care and maintenance
Always disconnect the appliance from the power before any cleaning or maintenance.
As the icemaker has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif)
will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a
dilute solution of water and mild detergent and drying to a shine with a clean cloth.
Proprietary stainless steel cleaners are available. We recommend the CDA E-Cloth available from the CDA Sales Team for cleaning
stainless steel surfaces.
You should remove and clean regularly the ice compartment drawer and both sections of the drip tray.
Once cleaning is complete, reconnect the mains power supply.
If the appliance is not to be used for prolonged periods of time, you should empty, clean thoroughly and turn off both the
electricity and water supply.
To empty the icemaker, follow the steps below:
1. Press the
2. Empty the ice drawer
3. Press the and buttons simultaneously.
button
,
4. The display will show ICE OFF WATER EMPTY for approximately five minutes until the cycle is complete.
IMPORTANT:
Steam cleaners must not be used when cleaning this appliance.
Ensure that all parts are correctly replaced after cleaning before attempting to use the icemaker.
You should replace the water filter every six months. Replacement filters are available from the CDA Sales Team.
5
Troubleshooting
Problem
Solution:
WATER MISSING shows in the display
Check the water supply is connected and switched on
ICE FAULT WATER READY shows in the display
at first switch on
Turn the icemaker off with
switching it on again.
, and the main switch on the side, before
The dispensed water has an unpleasant taste
Ensure that only water pipes suitable for drinking water are used
ICE FAULT shows in the display
Turn the icemaker off with
remove some ice and turn it on again.
We recommend that the unit is not left on permanently.
IMPORTANT:
Do not operate with a damaged cord or plug, after the appliance malfunctions or has been damaged in any way. You
should contact CDA Customer Care for inspection, repair or adjustment.
6
min. 200cm2
Installation
IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY SUITABLY
600
QUALIFIED PERSON.
We recommend that you seek the assistance of another individual when
installing this appliance.
450 min
392.5
560
This appliance requires a mains water supply and a connection to the drain/
waste system (drain connection is not supplied)
450 min
19
492.5
458
436
1. Slide the base unit into the housing ensuring the dimensions are
correct as per figure 1.
440
595
min. 200cm2
2. Fix the base unit in place by attaching the 10 screws in to
the holes.
fig. 1
3. Push the runners fully closed on the base unit.
4. Connect the plug to the plug socket. This must be accessible after
the appliance has been installed.
5. Using an appropriate supply pipe, connect one end of the hose to
the threaded inlet of the valve on the dispenser, located at the rear of
the appliance as shown in fig 3 and the other end to the mains supply
tap outlet. This must be accessible after the appliance has
been installed.
fig. 2
6. Install the inline filter
- Locate a convenient position to install the filter (C),
remembering that it must be accessible when it is to be
changed and functions best when mounted vertically.
G
A
H
I
B
- Screw the filter bracket (E) to the cupboard wall using screws (D), if
attaching the bracket to an interior wall use rawl plugs also.
J
- Remove the dust caps from the ends of the filter (C) and write the
installation date onto its label. Firmly push the pushfit connectors
(B and F) onto each end of the filter.
C
D
- Clip the filter (C) into its bracket (E) noting the direction of flow
through the filter (C) towards the ice maker.
E
- Cut the flexible pipe (A) so it is slightly longer than the required
lengths to and from the filter unit (C). When cutting the pipe use
a sharp Stanley knife, ensuring that the pipe is cut cleanly and
square at all ends.
F
- Firmly push the pipe (A) apx. 12mm into the pushfit connector (B).
- Screw the large pushfit adaptor (G) onto the 3 way tee (H)
A
fig. 3
- Firmly push the pipe (A) apx. 12mm into the pushfit connector (F)
and push fit adaptor (G).
7
7. Connect the drain pipe as shown in fig 6 and the other end to an
appropriate drain, for example a laundry standpipe or under
sink spigot . Drain connections to the plumbing side are not supplied.
8. Insert the appliance into the housing, ensuring that the runners
on the machine are located in the runners on the base unit. Then
slide the appliance fully into the housing.
i
Please note:
fig. 4
Due to the weight of this appliance, the housing unit must be secured to the
wall prior to installation.
ꢀ
You must ensure that all water connections are sound and check there are no
leaks and check the drain is in place, before completing installation.
For best performance, the mains water pressure must be between 0.1 - 3 bar.
Do not use outdoors.
Do not locate the drain outdoors.
Do not install near a hob or oven.
To reduce the risk of electric shock, do not mount over a sink.
fig. 5
fig. 6
8
Electrical information
Warning! This appliance must be earthed.
Green & Yellow to Earth
Brown to
Live
A
13 Amp
Fuse
B
Cord
Clamp
Blue to Neutral
The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug,
follow the steps below:
1. Remove the fuse cover and fuse.
2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover.
3. Replace fuse cover.
Important: Do not use the appliance without the fuse cover in position.
How to connect an alternative plug
If the fitted plug is not suitable for your socket outlet, then it should be cut off and disposed of safely to avoid the risk of
electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used.
As the colours of the wires in the mains lead of this appliance may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:-
•
•
•
The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E)
or by the Earth symbol or coloured GREEN and YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter (N), or
coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter (L) or
coloured RED or BROWN.
If in doubt regarding the electrical connection of this appliance, consult a qualified electrician. Do not shorten the
supply cable, the appliance may require removing for servicing.
N.B. Ensure that the plug socket is situated in an easily accessible place after installation.
9
10
To contact our Customer Care Department, or for Service,
please contact us on the details below.
Customer Care Department • The
Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
|