Cables to Go Computer Drive 29347 User Manual

4-Port USB SuperBooster  
Receiver Dongle  
Part #29347  
User Manual  
 
Features  
Extends the distance of a USB device from a USB-enabled computer up to 150ft  
One part of a total solution- transmitter is purchased separately giving you the  
flexibility to customize the configuration to your specific needs  
Transmitter options include a wall plate (part #29344) or a dongle (part #29348)  
Ideal for use with USB projectors, interactive whiteboards, cameras, printers,  
web cams, hubs, and other USB devices  
Bus-powered so no external power source is required  
Uses standard Cat5/Cat5E/Cat6 patch cord (not included) for ease of use and  
flexibility  
Included tool-less IDC RJ45 connector allows you to terminate your own cable  
Compliant with USB Specification 1.1  
Connectors:  
o Transmitter (sold separately): USB Type B Female; RJ45 Female  
o Receiver: Four USB Type A Female ports; RJ45 Female  
Package Contents  
USB SuperBooster Dongle- Receiver Unit  
(1) One RJ45 tool-less IDC connector  
User Guide  
2
 
Installing your USB SuperBooster Dongle  
The USB SuperBooster solution has a transmitter unit (sold separately) and a receiver  
unit. Make certain you install the transmitter unit at your computer or  
source side. The receiver unit needs to be installed on the device side.  
1) Install the Transmitter Wall Plate in a standard J-box where you want your  
source/computer or connect the Transmitter Dongle to your computer  
2) Connect the Receiver Dongle to your device using a standard A/B USB Cable or  
A/Mini-B USB Cable  
3) Use a pre-terminated Cat5/Cat5E/Cat6 cable (recommended) or terminate your  
own cable using the tool-less RJ45 connectors included to connect the transmitter  
and receiver together (see below for instructions on terminating your own cable)  
4) If using a Transmitter Wall Plate, plug your computer into the transmitter end  
(USB B side) using a standard A/B USB cable (The green LED will light to  
indicate you have a good connection to the wall plate)  
5) Turn your computer/source on and begin using your device  
Terminating a Cat5/Cat5E/Cat6 Cable Using the Tool-less IDC  
1) Open the plug by lifting the clear  
plastic end  
10) Thread the brown conductor on  
your Cat5/5E/6 cable into Pin 8  
11) Repeat steps 1-10 to terminate  
the other end of your Cat5/5E/6  
cable  
2) Pin 1 of the connector is on the  
left side of the clear plastic shell  
while Pin 8 is on the right side of  
the connector (with RJ45  
connector facing away from you)  
3) Thread the white/orange  
conductor on your Cat5/5E/6  
cable into Pin 1  
4) Thread the orange conductor on  
your Cat5/5E/6 cable into Pin 2  
5) Thread the white/green  
conductor on your Cat5/5E/6  
cable into Pin 3  
6) Thread the blue conductor on  
your Cat5/5E/6 cable into Pin 4  
7) Thread the white/blue conductor  
on your Cat5/5E/6 cable into Pin  
5
Pin 1  
Pin 8  
8) Thread the green conductor on  
your Cat5/5E/6 cable into Pin 6  
9) Thread the white/brown  
conductor on your Cat5/5E/6  
cable into Pin 7  
3
 
Termination Chart  
Pin Number Network (Cat5/5E/6)  
Conductor Color  
1
2
3
4
5
6
7
8
white/orange  
orange  
White/green  
Blue  
White/blue  
Green  
White/brown  
brown  
Application Diagram  
Transmitter  
Receiver  
3555 Kettering Blvd.  
Moraine, Ohio 45439  
1-800-293-4970  
1
 

BenQ Projector MW721 User Manual
Black Box Computer Hardware IC1000A User Manual
Black Decker Hot Beverage Maker JKC650KT User Manual
Black Decker Toaster T1900BDC User Manual
Blaupunkt Car Stereo System CD169 User Manual
Boca Research Printer FSP 42 User Manual
Bowers Wilkins Portable Speaker CWM LCR7 User Manual
Brother Printer QL 500W User Manual
Cal Spas Hot Tub LTR20111000 User Manual
Casio Watch DQR 300 User Manual