SmartSwitch 9000
9H532-24, 9H533-24, 9H531-24
and 9H539-24
24 Port Fast Ethernet Module
User’s Guide
9033050-02
Notice
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior
notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR
RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03867
1999 by Cabletron Systems, Inc.
All Rights Reserved
Printed in the United States of America
Order Number: 9033050-02
Cabletron Systems, LANVIEW, and MicroMMAC are registered trademarks and SmartSwitch is a trademark of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment uses, generates, and can radiate radio frequency energy and if not installed in accordance with the
operator’s manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause interference in which case the user will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class A
prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment
(VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be
required to take corrective actions.
i
Notice
CABLETRON SYSTEMS, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING GEOGRAPHICAL REGIONS:
CANADA
MEXICO
CENTRAL AMERICA
SOUTH AMERICA
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE
AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems, Inc. (“Cabletron”) that sets forth your
rights and obligations with respect to the Cabletron software program (“Program”) in the package. The Program may be contained in
firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE
TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER
OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO
CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL
REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS +1-603-332-9400. Attn: Legal
Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions
of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as
authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of
New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U.S.
Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain
countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export Administration
Regulations,You agree thatYou are a civil end user of the Program and agree thatYou will use the Program for civil end uses only and not for
military purposes.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration
Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the
Program, the source code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania, Armenia,
Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova,
North Korea, the People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such
other countries as may be designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the
direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identified
on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r any major component of a plant,
export to Country Groups D:1 or E:2 the direct product of the plant or a major component thereof, if such foreign produced direct product is
subject to national security controls as identified on the U.S. Commerce Control List or is subject to State Department controls under the U.S.
Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely at private expense;
(ii) contains “restricted computer software” submitted with restricted rights in accordance with section 52.227-19 (a) through (d) of the
Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data belonging to Cabletron
and/or its suppliers. For Department of Defense units, the Product is considered commercial computer software in accordance with DFARS
section 227.7202-3 and its successors, and use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
ii
Notice
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty,
expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS,
AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE
FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE
DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF
CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION
OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT
APPLY TO YOU.
CABLETRON SYSTEMS SALES AND SERVICE, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED STATES OF AMERICA AND BY
UNITED STATES OF AMERICA GOVERNMENT END USERS.
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE
AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems Sales and Service, Inc. (“Cabletron”) that
sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in the package. The Program may be
contained in firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND
BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND
DISCLAIMER OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED
PRODUCT TO CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A
FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS +1-603-332-9400. Attn: Legal
Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions
of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as
authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state and federal courts of
New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U.S.
Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain
countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export Administration
Regulations,You agree thatYou are a civil end user of the Program and agree thatYou will use the Program for civil end uses only and not for
military purposes.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration
Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the
Program, the source code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania, Armenia,
Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova,
North Korea, the People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such
other countries as may be designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the
direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identified
on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r any major component of a plant,
iii
Notice
export to Country Groups D:1 or E:2 the direct product of the plant or a major component thereof, if such foreign produced direct product is
subject to national security controls as identified on the U.S. Commerce Control List or is subject to State Department controls under the U.S.
Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely at private expense;
(ii) contains “restricted computer software” submitted with restricted rights in accordance with section 52.227-19 (a) through (d) of the
Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data belonging to Cabletron
and/or its suppliers. For Department of Defense units, the Product is considered commercial computer software in accordance with DFARS
section 227.7202-3 and its successors, and use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty,
expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS,
AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE
FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE
DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF
CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION
OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT
APPLY TO YOU.
CABLETRON SYSTEMS LIMITED
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE FOLLOWING GEOGRAPHICAL
REGIONS:
EUROPE
MIDDLE EAST
AFRICA
ASIA
AUSTRALIA
PACIFIC RIM
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ THIS LICENSE
AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems Limited (“Cabletron”) that sets forth your
rights and obligations with respect to the Cabletron software program (“Program”) in the package. The Program may be contained in
firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE
TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER
OF LIABILITY. IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO
CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL
REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS +1-603-332-9400. Attn: Legal
Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the terms and conditions
of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the United States or as
authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be governed in accordance with English law. The English courts shall have
exclusive jurisdiction in the event of any disputes.
iv
Notice
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by agencies of the U.S.
Government, including the U.S. Department of Commerce, which prohibit export or diversion of certain technical products to certain
countries, unless a license to export the product is obtained from the U.S. Government or an exception from obtaining such license may be
relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export Administration
Regulations,You agree thatYou are a civil end user of the Program and agree thatYou will use the Program for civil end uses only and not for
military purposes.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export Administration
Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You agree not to (i) reexport or release the
Program, the source code for the Program or technology to a national of a country in Country Groups D:1 or E:2 (Albania, Armenia,
Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia, Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova,
North Korea, the People’s Republic of China, Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such
other countries as may be designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the
direct product of the Program or the technology, if such foreign produced direct product is subject to national security controls as identified
on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r any major component of a plant,
export to Country Groups D:1 or E:2 the direct product of the plant or a major component thereof, if such foreign produced direct product is
subject to national security controls as identified on the U.S. Commerce Control List or is subject to State Department controls under the U.S.
Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely at private expense;
(ii) contains “restricted computer software” submitted with restricted rights in accordance with section 52.227-19 (a) through (d) of the
Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in all respects is proprietary data belonging to Cabletron
and/or its suppliers. For Department of Defense units, the Product is considered commercial computer software in accordance with DFARS
section 227.7202-3 and its successors, and use, duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes no warranty,
expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY CABLETRON IN WRITING,
EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS,
AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS SUPPLIERS BE LIABLE
FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS,
BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE
DAMAGES, OR OTHER LOSS) ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF
CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION
OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT
APPLY TO YOU.
v
Notice
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
THE 9H539-24 MODULE USES CLASS 1 LASER TRANSCEIVERS.
READ THE FOLLOWING SAFETY INFORMATION BEFORE
INSTALLING OR OPERATING THESE MODULES.
The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop eliminates the need for
maintenance checks or adjustments. The output is factory set, and does not allow any user adjustment. Class 1 Laser transceivers comply with
the following safety standards:
•
•
•
21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).
IEC Publication 825 (International Electrotechnical Commission).
CENELEC EN 60825 (European Committee for Electrotechnical Standardization).
When operating within their performance limitations, laser transceiver output meets the Class 1 accessible emission limit of all three
standards. Class 1 levels of laser radiation are not considered hazardous.
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
LASER RADIATION AND CONNECTORS
When the connector is in place, all laser radiation remains within the fiber. The maximum amount of radiant power exiting the fiber (under
-6
normal conditions) is -12.6 dBm or 55 x 10 watts.
Removing the optical connector from the transceiver allows laser radiation to emit directly from the optical port. The maximum radiance
from the optical port (under worst case conditions) is
-2
3
2
0.8 W cm or 8 x 10 W m sr-1.
Do not use optical instruments to view the laser output. The use of optical instruments to view laser output increases eye hazard.
When viewing the output optical port, power must be removed from the network adapter.
vi
Notice
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC
73/23/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name: Mr. J. Solari
European Representative Address: Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG14 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950
Equipment Type/Environment: Networking Equipment, for use in a Commercial or Light Industrial
Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this notice conforms to the
above directives.
Manufacturer
Legal Representative in Europe
Mr. Ronald Fotino
Mr. J. Solari
___________________________________
___________________________________
Full Name
Full Name
Compliance Engineering Manager
Managing Director - E.M.E.A.
___________________________________
___________________________________
Title
Title
Rochester, NH, USA
Newbury, Berkshire, England
___________________________________
___________________________________
Location
Location
vii
Notice
viii
Contents
Using DIP Switch 6................................................................................................ 2-4
Cabling Requirements.................................................................................................. 2-7
100BASE-TX Network........................................................................................... 2-7
SMB-1 Bus............................................................................................................... 3-3
SMB-10 Bus............................................................................................................. 3-3
INB Interface.................................................................................................................. 3-4
i960 Core......................................................................................................................... 3-4
Technical SpeciÞcations......................................................................................... 5-1
CPUs................................................................................................................. 5-1
Memory............................................................................................................ 5-1
ix
Contents
Service......................................................................................................................5-2
Physical....................................................................................................................5-2
Dimensions ......................................................................................................5-2
Weight...............................................................................................................5-2
Environment....................................................................................................5-2
x
Chapter 1
Introduction
10/100 Mbps Fast Ethernet interface modules for the Cabletron Systems
SmartSwitch 9000 chassis. The 9H532-24 provides 24 RJ45 10/100 Ethernet ports
and the 9H533-24 provides 24 10/100 Ethernet ports via two RJ21 Telco ports. The
9H531-24 provides 24 MTRJ MMF switched ports and the 9H539-24 provides 24
SMF switched ports.
The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 can be used to connect
individual high-bandwidth user devices, such as workstations, or to provide a
central switching point for multiple 10/100 Mbps Fast Ethernet segments.
Features
Connectivity
The 9H532-24 connects to Ethernet networks or workstations through the 24 RJ45
ports on the front panel. The 9H533-24 supports two RJ21 Telco connectors that
provide up to 24 ports of 10/100 mbps Ethernet connectivity. These ports are
IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX compliant. The ports support
Category 5 Unshielded Twisted Pair cables with an impedance between 85 and
111 ohms at lengths up to 100 meters. In addition, Category 3 cabling can be used
for 10 Mbps only.
The 9H531-24 uses MJ-RT connectors that support multimode Þber connectivity.
The 9H539-24 uses MT-RJ connectors that support single Þber connectivity. Both
the 9H531-24 and the 9H539-24 are 100Base-FX compliant.
1-1
Introduction
FAST ENET
9H532-24
FAST ENET
9H533-24
FAST ENET
9H531-24
FAST ENET
9H539-24
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
24
23
22
21
20
19
18
17
24
16
15
14
13
12
13
12
11
10
9
1
8
7
6
5
4
3
2
1
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
Figure 1-1. The 9H532-24, 9H533-24, 9H531-24 and 9H539-24
1-2
Introduction
Auto-Negotiation
The twisted pair ports on the front panel of the 9H532-24 and 9H533-24 modules
have the ability to auto-negotiate the type of connection required to provide a link
to another device. During Auto-Negotiation, two devices automatically exchange
information ÒtellingÓ each other what their operating capabilities are. The Auto-
Negotiation feature targets the maximum capabilities that can be reached
between the two devices. For example, the module adjusts to 100 Mbps when the
device on the other end of the connection can also adjust between 10 Mbps or
100 Mbps. If the device on the other end of the connection can only operate at
10 Mbps, then the 9H532-24 adjusts to 10 Mbps operation.
When Auto-Negotiation is supported at both ends of a link, the two devices
dynamically adjust to full or half duplex operation based on the maximum
capability that can be reached between the two devices. If the device connected to
the 9H532-24 and 9H533-24 cannot auto-negotiate, the 9H532-24 and 9H533-24
interface operates according to the speed of the other device, in half duplex mode.
For a full duplex only device, the port may be manually conÞgured to full duplex.
Both the 9H531-24 and the 9H539-24 support Full Duplex Switched Ethernet
(FDSE) with 100 Mbps operation only. On the 9H532-24 and the 9H533-24, each
switched Fast Ethernet port can be conÞgured to operate in FDSE mode, with 10
or 100 Mbps operation. FDSE allows each port to provide up to 200 Mbps of
bandwidth.
Runtime IP Address Discovery
This feature enables the modules to automatically accept an IP address from a
Boot Strap Protocol (BootP) server on the network into NVRAM without
requiring a user to enter an IP address through Local Management.
When the modules are connected to the network and powered up, Runtime IP
Address Discovery (RAD) checks the modules for an IP address. If one has not yet
been assigned (module and SmartSwitch 9000 chassis IP address set to 0.0.0.0),
RAD checks to see if any of the module interfaces have a link. If so, RAD sends
out Reverse Address Resolution Protocol (RARP) and BootP requests to obtain an
IP address from a RARP or BootP server on the network.
The RAD requests start at an interval of one per second. The interval then doubles
after every transmission until an interval of 300 seconds is reached. At this point,
the interval remains at 300 seconds. The RAD requests continue until an IP
address is received from a RARP or BootP server, or an IP address is entered
using Local Management.
SmartTrunk
SmartTrunk, also referred to as SmartTrunking, is Cabletron SystemsÕ
terminology for load balancing or load sharing. SmartTrunk technology provides
an easy-to-implement mechanism to group, or aggregate, multiple links of any
technology together to scale the backbone bandwidth beyond the limitations of a
1-3
Introduction
single link. All links are user-conÞgurable so administrators can scale the
backbone bandwidth by adding SmartTrunk links. The beneÞts of SmartTrunking
include the following:
¥
¥
¥
All purchased bandwidth is used.
Distributed, resilient links increase reliability and performance.
Multiple technologies are supported within a single trunk for maximum
ßexibility.
For information on SmartTrunk conÞguration, refer to the
SmartTrunk UserÕs Guide.
NOTE
Management
Management of the 9H532-24, 9H533-24, 9H531-24 and 9H539-24 modules and
SmartSwitch chassis and any optional equipment is accomplished using the Local
Management application or remote SNMP management stations. Local
Management is accessible through the RS232 COM port on the Environmental
Module using a local VT100 terminal, or a remote VT100 terminal via a modem
connection, and in-band via a Telnet connection. In-band remote management is
possible through Webview or any SNMP compliant Network Management
Software.
Local Management provides the ability to manage the 9H532-24, 9H533-24,
9H531-24 and 9H539-24. Local Management information for non-Ethernet HSIMs
or VHSIMs is included in their respective userÕs guide. For details on how to get
manuals, refer to the Related Manuals section.
WebView
The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 modules can be managed using
Cabletron WebView, a browser-based utility. There is no software to install as this
management capability is built into each module.
Remote Monitoring (RMON)
The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 support all nine Ethernet
RMON groups. The Statistics, Alarms, Events and History groups are enabled on
all ports by default.
Cabletron Systems RMON Actions is a vendor-speciÞc extension of RMON and
provides the ability to set an ÒActionÓ on any SNMP MIB variable. The Action can
be triggered by setting an RMON Event and/or Alarm. An example of an Action
would be to turn off a MIB-2 interface if a broadcast threshold is crossed.
1-4
Introduction
Broadcast Suppression
Broadcast Suppression enables a user to set a desired limit of receive broadcast
frames per port/per second to be forwarded out the other ports on the module up
to the set limit. Any broadcast frames above this speciÞed limit are dropped. In
the event that broadcast frames are being suppressed, multicast and unicast
frames continue to be switched.
Port Redirect Function
The Port Redirect function, also referred to as ÒPort Mirroring,Ó is a
troubleshooting tool used to map trafÞc from a single source port to a destination
port within the chassis. This feature allows all packets, including those with
errors, to be copied and sent to an analyzer or RMON probe. The analyzer or
RMON probe will see the data as if it is directly connected to the LAN segment of
the source port.
Flow Control
Flow Control is a method of managing the ßow of frames between two devices. It
ensures that a transmitting device does not overwhelm a receiving device with
data. This enables the receiving device to communicate with the transmitting
device, and to have it pause its transmission while the receiving device processes
the frames already received. Flow control can be enabled or disabled on a port-by-
port basis. Both devices must support the IEEE 802.3x standard for ßow control to
work.
The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 support the following two types
of ßow control:
¥
¥
frame based 802.3x
back pressure
Frame based 802.3x ßow control is supported on all Ethernet ports operating in
the full duplex mode.
Back pressure ßow control is supported on all Ethernet ports operating in the
standard mode of operation.
802.1p Port Priority
The IEEE 802.1p standard is used to assign a default priority to the frames
received without priority information in their tag header, and to map prioritized
frames to the appropriate transmit queues.
conÞguration can be changed by the administrator.
1-5
Introduction
Table 1-1. Priority Queuing Configuration
Priority Indicator
Transmit Queue
7
6
5
4
3
2
1
0
3
3
2
2
1
0
0
1
Switching Options
The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 provide IEEE Standard-based
802.1 switching or SecureFast Switching Virtual Network Services. In the 802.1
mode (the default mode of operation), the switch functions as an 802.1D switch.
When until VLANs are conÞgured, it operates as an 802.1Q switch.
Standards Compatibility
The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 are fully compliant with the
IEEE 802.3, 802.3x, 802.3u, 802.1Q, and 802.1p standards. The 9H532-24, 9H533-24,
9H531-24 and 9H539-24 provide IEEE 802.1D Spanning Tree Algorithm (STA)
support to enhance the overall reliability of the network and protect against
ÒloopÓ conditions. The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 support a
wide variety of industry standard MIBs including RFC 1573 (MIB II), RFC 1271
(RMON), RFC 1493 (Bridge MIB), RFC 1354 (FIB MIB), and RFC 1190 (Path MTU
Discovery). A full suite of Cabletron Systems Enterprise MIBs provide a wide
array of statistical information to enhance troubleshooting.
For information about how to extract and compile individual MIBs, contact
Cabletron Systems.
GARP Switch Operation
Some or all ports on the switch may be activated to operate under the Generic
Attribute Registration Protocol (GARP) applications, GARP VLAN Registration
Protocol (GVRP) and/or GARP Multicast Registration Protocol (GMRP).
GARP is a protocol, or set of rules, that outlines a mechanism for propagating the
port state and/or user information throughout a bridged LAN to keep track of
users and VLANs on the network fabric. MAC bridges and end users alike can
1-6
Introduction
take part in the registration and de-registration of GARP attributes such as VLAN
and multicast group membership.
LANVIEW Diagnostic LEDs
LANVIEW diagnostic LEDs serve as an important troubleshooting aid by
providing an easy way to observe the status of individual ports and overall
network operations.
Year 2000 Compliance
The 9H532-24, 9H533-24, 9H531-24 and 9H539-24 modules and the SmartSwitch
9000 chassis have an internal clock that can maintain the time and date beyond
the year 1999.
Related Manuals
The Cabletron Systems manuals listed below should be used to supplement the
procedures and technical data contained in this manual.
SmartSwitch 9000 Installation Guide
SmartSwitch 9000 9C300-1 Environmental Module UserÕs Guide
SmartSwitch 9000 9C214-1 AC Power Supply UserÕs Guide
SmartSwitch 9000 9X5XX Series Local Management UserÕs Guide
Cabling Guide
Ethernet Technology Guide
Network Troubleshooting Guide
WebView UserÕs Guide
SmartTrunk UserÕs Guide
1-7
Introduction
1-8
Chapter 2
Installing the SmartSwitch 9000
Module
Only qualiÞed personnel should perform installation procedures.
Unpacking the Module
1. Carefully remove the module from the shipping box. (Save the box and
packing materials in the event the module must be reshipped.)
2. Remove the module from the plastic bag. Observe all precautions to prevent
damage from Electrostatic Discharge (ESD).
3. Carefully examine the module, checking for damage. If any damage exists,
DO NOT install the module. Contact Cabletron Systems immediately.
User Accessible Components
Figure 2-1 shows the various components that are accessible to the user. These
consist of an eight-position DIP switch, replaceable PROMs and sockets for RAM.
These components will be used for future upgrades. Instructions for installing the
components will be supplied with the upgrade kit.
2-1
Installing the SmartSwitch 9000 Module
An eight-position DIP switch is located on the module card as shown in
See the Cautions at the end of this table.
Table 2-1. Function of DIP Switch
Switch
Function
Description
When toggled, this switch clears user-entered
passwords stored in NVRAM, and restores the
default passwords. Once reset you can use the
defaults or enter new passwords.
Clear
Password
8
1
The module uses NVRAM to store user-
entered parameters such as IP addresses,
device name, etc. To reset these parameters to
the factory defaults, toggle this switch. Once
reset, you can use the defaults or enter new
parameters, which are stored in NVRAM
when the module is powered down, and
remain there until the switch is toggled again.
Clear
NVRAM
7
2
Toggling this switch after pulling the board
out of the SmartSwitch 9000, clears download
information from NVRAM and forces image
files to be downloaded from the station
connected to the EPIM on the Environmental
Module configured to act as that modulesÕ
Force BootP
Download
6
5
4
3
2
1
Reserved
Reserved
Reserved
Reserved
Reserved
For Factory Use Only
For Factory Use Only
For Factory Use Only
For Factory Use Only
For Factory Use Only
1. Caution: Do not toggle Switch 8 unless you intend to reset the user-
conÞgured passwords to their factory default settings.
!
CAUTION
2. Caution: Do not toggle Switch 7 unless you intend to reset the user
parameters to the factory default settings.
2-3
Installing the SmartSwitch 9000 Module
Using DIP Switch 6
The purpose of DIP switch 6 is to force a Flash download from a BootP server
through the EM-EPIM. The Þrst step in this process is to conÞgure the BootP
server. ConÞgurations of BootP servers can differ from platform to platform and
from one operating system to another. Read the userÕs manual on BootP and TFTP
serving for the correct Þles to edit and the correct Þles to execute for the server.
After conÞguration of the BootP server the module can then have the switch state
changed on dip switch 6 to initiate BootP and TFTP requests.
When the state of dip switch 6 is changed, the module begins requesting a BootP
server in an attempt to receive a Flash image download. The modules boot PROM
initiates a BootP sequence. During this sequence, the module requests an IP
address and a Þlename from the BootP server. The module then requests a TFTP
of the Þle and receives the download of the image. The module will not function
until the Flash image is downloaded from the BootP and TFTP server.
If a BootP and TFTP are not intended at this time, this process may be stopped by
resetting the module. Resetting is done by pushing the reset button on the
module, power cycling the chassis, or removing the module from the chassis and
the module again looks for a BootP server, but will time-out after about four
minutes. After the time-out, the module boots from Flash memory. The next time
the power is cycled, the module will boot from Flash memory and not request the
BootP server.
Installing the Module into the SmartSwitch 9000
Chassis
To install the SmartSwitch 9000 module, follow the steps below:
The INB Terminator Modules must be installed on the rear of the fourteen slot
chassis before powering up this module. The INB Terminator Modules are not
NOTE
required on the six slot chassis. Refer to the INB Terminator Modules
Installation Guide for information and installation procedure.
1. Remove the blank panel covering the two slots in which the module is being
installed. All other slots must be covered, if other modules are not being
installed, to ensure proper airßow and cooling.
2. Attach one end of the ESD wrist strap packaged with the SmartSwitch 9000
chassis to your wrist. Plug the other end into the ESD Wrist Strap Grounding
receptacle in the lower right corner of the SmartSwitch 9000 chassis shown in
2-4
Installing the SmartSwitch 9000 Module
3. Grasp the module and slide it into the slots. Make sure that the moduleÕs
circuit card is between the card guides, as shown in Figure 2-2. Check both the
upper and lower tracks of the card. Take care that the module slides in straight
and engages the backplane connectors properly.
FK
FK
FK
I
I
Jack for ESD
wrist strap
Metal Back-Panel
Circuit Card
Card Guides
Warning:
Ensure that the circuit card is between the card guides.
Lock down the top and bottom plastic tabs
at the same time, applying even pressure.
Figure 2-2. Installing the Module
2-5
Installing the SmartSwitch 9000 Module
The Reset Switch
Use the reset switch to reset the moduleÕs processor, shutdown (power down) the
module, and/or restart the module.
¥
¥
¥
To reset the moduleÕs i960 processor, press the reset switch twice within three
seconds.
To shut down the module, press and hold the reset switch for three or more
seconds.
To restart the module, press the reset switch momentarily.
SNMP management may be used to disable this switch to enhance module
security.
Reset Switch
SMB
CPU
Figure 2-3. The Reset Switch
2-6
Installing the SmartSwitch 9000 Module
Cabling Requirements
10BASE-T Network
When connecting a 10BASE-T segment to the front panel ports of a 9H532-24 or a
9H533-24 module, ensure that the network meets the Ethernet network
requirements of the IEEE 802.3 standard for 10BASE-T. If a port is to operate at
100 Mbps, Category 5 cabling must be used. For 10 Mbps operation only,
Category 3 cabling can be used.
100BASE-TX Network
The 9H532-24 and the 9H533-24 support Category 5 UTP cabling with an
impedance between 85 and 111 ohms for 10 and 100 Mbps operation. The device
at the other end of the twisted pair segment must meet IEEE 802.3u 100BASE-TX
Fast Ethernet network requirements for the devices to operate at 100 Mbps. Refer
to the Cabletron Systems Cabling Guide for details.
100BASE-FX Network
The 9H531-24 and 9H539-24 support 100BASE-FX. When connecting a
100BASE-FX segment to any of the front panel ports, ensure that the network
meets the optical performance requirements for 100BASE-FX IEEE 802.3u
standard.
The 9H531-24 supports multimode Þber cables at the 1300 nm wavelength, at
lengths of up to 2 km.
The 9H539-24 supports single mode Þber at the 1300 nm wavelength. Class 1
lasers are used to support single mode 9/125 micon Þber cables up to 15 km in
length.
2-7
Installing the SmartSwitch 9000 Module
2-8
Chapter 3
Technical Overview
SmartSwitch Architecture
The SmartSwitch Architecture of the 9H532-24, 9H533-24, 9H531-24 and 9H539-24
modules, as shown in Figure 3-1, are conÞgurable for one of two modes of
operation: traditional IEEE 802.1 switching, or SecureFast switching. The modules
support only one of these modes of operation at any one time.
When operating in traditional IEEE 802.1 switch mode, the 9H532-24, 9H533-24,
9H531-24 and 9H539-24 make Þltering/forwarding decisions based on
Destination Address (DA), with standard IEEE 802.1D learning. 802.1Q VLANs
are also supported.
Spanning tree operation for the 9H532-24, 9H533-24, 9H531-24 and 9H539-24 may
be conÞgured to adhere to IEEE 802.1D, DEC, or none. The default Spanning Tree
Algorithm is 802.1D.
When operating in SecureFast switch mode, all Þltering/forwarding decisions are
made on a DA-SA pair and its in and out port on a connection-orientated basis.
SecureFast switching mode provides value-added network services including
dynamic VLANs, Topology, Connectivity, IP Multicast, Control, Security,
Application, Address Management, Dynamic Mapping, and Directory services.
For example, Topology Services includes conÞgurable options ranging from
simple spanning tree implementations to fully-meshed active topologies. Other
services and features supported in SecureFast switching mode are described in
detail in the Cabletron SystemÕs White Paper, IP Host Communication in
Bridged, Routed and SecureFast Networks.
3-1
Technical Overview
SmartSwitch 9000
Backplane
DC/DC
Converter
48 Volt
Power Bus
SMB 1
Diagnostic
Controller
i960
Processor
Octal
Mac
SMB 10
Ethernet
Controller
INB
ASIC
A
B
Smart
Switch
Fabric
INB
ASIC
I
N
B
Front
Panel
Ports
(24)
Octal
Mac
Octal
Mac
Figure 3-1. Block Diagram
System Management Buses
There are two management channels within the SmartSwitch 9000 system: the
SMB-1 and the SMB-10. These buses provide out-of-band management and
inter-module management communication.
3-2
Technical Overview
SMB-1 Bus
The SMB-1 is a 1 Mbps management bus located within the SmartSwitch 9000.
This bus is utilized by all diagnostic controllers in the system including
connectivity modules, power supply modules and the environmental module.
The SMB-1 transports inter-chassis information between system components,
such as power and environmental information, as well as diagnostic messages.
Periodic loop-back tests are performed by all modules that share this bus to
ensure the validity of SMB-1. In the event a failure is detected on SMB-1, the
SMB-10 may be used as an alternate communication channel.
SMB-10 Bus
The SMB-10 is a 10 Mbps management bus located within the SmartSwitch 9000,
which is also used for inter-chassis communication of modules as well as serving
as an out-of-band management channel into the SmartSwitch 9000. The SMB-10 is
externalized from the chassis via an optional Ethernet Port Interface Module
(EPIM) located on the front of the Environmental Module. Through an EPIM
connection, full SNMP management of the SmartSwitch 9000 is available out-of-
band from user data. Modules that share the SMB-10 bus periodically send out
loop-back packets to ensure the validity of SMB-10. In the event a fault is detected
on the SMB-10, the SMB-1 can be used as an alternate communication channel by
the modules.
System Diagnostic Controller
This diagnostic controller is composed of a Z-80 microprocessor and its
supporting logic. The diagnostic controller is designed to control the power-up
sequencing of modules, monitor the 9H532-24, 9H533-24, 9H531-24 and 9H539-24
input and output power parameters, keep watch over the main host processor, as
well as monitor the temperature and control the SMB LANVIEW diagnostic LED.
Although the diagnostic controller and the main host processor can operate
independent of each other if needed, they exchange information about each
otherÕs status and overall module condition. The information gathered by the
diagnostic controller is available to the network manager via local/remote
management and the LCD located on the Environmental Module. The 9H532-24,
9H533-24, 9H531-24 and 9H539-24 have been designed so that in the event of a
diagnostic controller fault, the 9H532-24, 9H533-24, 9H531-24 and 9H539-24 will
continue to function.
3-3
Technical Overview
DC/DC Converter
The DC/DC converter converts the 48 VDC on the system power bus to the
necessary operating voltages for its host network services module. The diagnostic
controller monitors and controls the operation of the DC/DC converter.
INB Interface
Each module attaches to both INB A and INB B and has two INB ASICs. The INB
ASICs use 64-byte Ethernet frames for transmission onto the INBs at 66 MHz.
The 9X5XX modules are fully compatible with the the Þrst generation 9X4XX
modules. The Þrst generation modules communicate only on INB B using a
56-byte canonical frame format, at 40 MHz. If the newer module detects a Þrst
generation module on the backplane, it automatically changes from the fast
66 MHz Ethernet frames, to the Þrst generation compatible 40 MHz canonical
frame on INB B only. INB A is used only by the 9X5XX modules and remains at
the higher speed.
i960 Core
The i960 core provides modules host services, the SNMP protocol stacks, to
support industry standard MIBs, as well as Cabletron enterprise extension MIBs
for each media type. Management services, such as telnet, WebView and network
address to MAC address mapping, are also provided by the i960 core.
3-4
Chapter 4
LANVIEW LEDs
The front panel LANVIEW LEDs indicate the status of the module and may be
used as an aid in troubleshooting. Figure 4-1 shows the LANVIEW LEDs of the
9H532-24, 9H533-24, 9H531-24 and 9H539-24 module.
The LED Mode Switch
The 9H532-24 and 9H533-24 have an LED mode switch, located on the front
panel, that allows the user to change the function of the switch port LEDs. Refer to
Figure 4-1. When the switch is in the UP position, the LEDs indicate the receive
(RX) and transmit (TX) status of the Þxed ports. When the mode switch is in the
DOWN position, the LEDs indicate at what speed the applicable port is currently
operating (10 Mbps or 100 Mbps) and if the applicable port is operating in
standard (half) or full duplex mode.
deÞnitions of the LED states that occur when the LED mode switch is in the
DOWN position.
4-1
LANVIEW LEDs
FAST ENET
9H532-24
System Status
INB Transmit
INB Receive
LED Mode Switch
24
23
22
21
20
19
18
17
DPX
SPD
Receive (RX)
Transmit (TX)
RX
TX
A
(Mode Switch in UP Position)
16
15
14
Full Duplex
DPX
13
12
Status
RX
TX
SPD
B
Speed Status
11
10
9
(Mode Switch in DOWN Position)
A
B
LED functions when LED MODE
switch is in the RX-TX position.
This is the default switch setting.
8
7
6
5
4
3
2
1
LED functions when LED MODE
switch is in the DPX-SPD position.
Figure 4-1. The LANVIEW LEDs (9H532-24 shown) and LED Mode Switch
4-2
LANVIEW LEDs
The functions of the two System Status LEDs, System Management Bus (SMB)
Table 4-1. System Status (SMB and CPU) LEDs
LED Color
State
Description
Fully operational
Green
Yellow
Functional
Testing
Power-up testing
Yellow (Flashing) Crippled
Not fully operational (e.g., one bad port)
Blinks yellow and green while booting
Normal power-up reset
Yellow/Green
Red
Booting
Reset
Red (Flashing)
Off
Failed
Fatal error has occurred
Power off
Module powered off
Table 4-2. INB Transmit LED
LED Color
State
Green (Flashing)
Yellow (Flashing)
Red (Flashing)
Red
Data activity
Port in standby state
Collision
Fault
Off
No activity, Port disabled
4-3
LANVIEW LEDs
Table 4-3. INB Receive LED
LED Color
State
Green (Flashing)
Link, Port disabled
Link, Port enabled, No activity
Link, Port enabled, Activity
Fault
Green
Yellow (Flashing)
Red
Off
No link
The functions of the Ethernet Transmit and Ethernet Receive LEDs are listed in
MODE switch is in the RX-TX position.
Table 4-4. Ethernet Transmit LEDs
Color
State
Green (Flashing)
Yellow (Flashing)
Red
Activity (Flashing rate indicates rate of activity)
Port in standby state
Port disabled
Collision
Red (Flashing)
Off
No activity
Table 4-5. Ethernet Receive LEDs
LED Color
State
Green
Link, No activity
Yellow (Flashing)
Red
Link, Activity (Flashing rate indicates rate of activity)
Port disabled no link
Red (Flashing)
Off
Port disabled with link
No link, No activity
4-4
LANVIEW LEDs
the DPX-SPD position.
Table 4-6. DPX Status LEDs (9H532-24 only)
LED Color
Green
State
Port is operating in full duplex mode (20 Mbps or
200 Mbps).
Yellow
Port is in standard (half duplex) mode (10 Mbps or
100 Mbps).
Table 4-7. SPD LEDs (9H532-24 only)
LED Color
State
Green
Port is linked and operating at 100 Mbps.
Port is linked and operating at 10 Mbps.
Yellow
4-5
LANVIEW LEDs
4-6
Chapter 5
Specifications
Technical Specifications
CPUs
PowerPC
Intel i960 RISC based microprocessor
Memory
8 MB Flash Memory (expandable to 16 MB)
32 MB DRAM (local)
4 MB Memory (Shared)
Network Interface
24 RJ45 Unshielded Twisted Pair ports (9H532-24) - 10BASE-T/100BASE-TX
24 10/100 Mbps ports via 2 RJ21 Telco connectors (9H533-24) -
10BASE-T/100BASE-TX
24 MT-RJ multimode Þber ports (9H531-24) - 100BASE-FX
24 MT-RJ single mode Þber ports (9H539-24) - 100BASE-FX
Performance
Module Switch Fabric bandwidth 3.3 Gbps
Module Throughput
Source Address Table
2.2 Mpps
16 K entries
5-1
Specifications
Regulatory Compliance
It is the responsibility of the person who sells the system to which the module will
be a part to ensure that the total system meets allowed limits of conducted and
radiated emissions.
!
CAUTION
This equipment meets the following safety and electromagnetic compatibility
(EMC) requirements:
Safety
UL 1950, CSA C22.2 No. 950,
EN 60950, IEC 950, and 73/23/EEC
Electromagnetic Compatibility
(EMC)
FCC Part 15, EN 55022, CSA C108.8,
EN 50082-1, AS/NZS 3548, VCCI V-3,
and 89/336/EEC
Service
MTBF (MHBK-217E)
MTTR
>200,000 hrs.
<0.5 hr.
Physical
Dimensions
35.0 D x 44.1 H x 3.0 W centimeters
(13.8 D x 17.4 H x 1.2 W inches)
Weight
Unit:
Shipping:
4.5 kg (10 lb)
5.4 kg (12 lb)
Environment
Operating Temperature
Storage Temperature
Relative Humidity
5 to 40¡ C (41¡ to 104¡F)
-30 to 73¡ C (-22¡ to 164¡F)
5% to 90% non-condensing
5-2
|