DVD89
DVD player
User’s manual - supplement
2
COMPACT
DIGITAL AUDIO
Play/Pause
Stop
Skip/Scan
Open/Close
DVD89
Using the DVD setup menu system
Setting up the player: Basic
In many places of this guide, the DVD player’s Setup Menu needs to be
adjusted to match your specific audio/video configuration. To access
the DVD player’s Setup Menu simply press the SETUP button on the
remote control when the disc is stopped. When asking you to make
menu adjustments, we will use the following terminology to indicate the
location of the desired function:
Follow these simple steps to successfully set up your player for use in
your system:
Use the best available video connection
BETTER
BEST
Setup Menu Name > Menu Item > Submenu Item (or Selection)
(Y)
Setup Menu Name is the actual name of the uppermost setup menu
level. With the DVD89 Player there are exactly five (5) Setup Menu pages
or sections, each represented by an icon on the top of the Setup Menu
screen. They are: General Setup Page, Speaker Setup Page, Audio
Setup Page, Video Setup Page, and Preference Page.
(Pb/Cb)
(PrCr)
DVI In
GOOD
Video In
Menu Item is the parameter to be adjusted which appears below the Top
Menu Name. It is the list of items on the left of the current Setup screen.
S-Video
Submenu Item (or the selection) is the actual numeric or descriptive
element that represents the change being made to the selected
parameter. It is the item located to the immediate right of its
corresponding Menu Item.
This diagram should give a good description of the various elements and
their context. In this screen we could, for example, instruct you to set the
Rear Speaker parameter to Small in the Speaker Setup Page. To
indicate where we were, you would see the following: Speaker Setup
Page > Rear Speaker > Small.
Rear Panel
Setup Menu Name
Menu Item
If an HDMI or DVI connection is present on your television or display, use
it. The DVD89 player has an HDMI (digital) video output which presents
the highest possible resolutions and video quality. If the television you
are using has only component video inputs, then select a component
video cable (it has three RCA-style connections on each end typically
colored red, green, and blue). If your television is older and has neither
of these inputs you may use s-video (a special 4-pin cable) or composite
(typically a single yellow RCA-style cable).
Submenu Item
3
Determine your display type
For best performance, your DVD89 player must be correctly configured
for playback even before the first disc is inserted. This is done under
General Setup Page > TV Display in the Setup Menu.
If you have a 4:3 or standard definition screen as pictured above, select
one of these options:
• 4:3 Pan/Scan – 4:3 TV Pan and Scan. Choose when the display is 4:3.
Both sides of a widescreen image are clipped (you lose about 30% of
the picture).
• 4:3 Letterbox – 4:3 TV Letterbox. Choose when the display is 4:3.
Widescreen image is displayed in “letterbox” format with black
borders on top and bottom (preferred).
Notes when using HDMI
• If your AV receiver or display has an HDMI input, you can use the
included HDMI cable to connect the DVD player to the TV. This is the
most preferred connection method as it provides a pure digital
connection for video signal and, depending upon your system, can
also deliver high resolution digital audio over the same cable.
Widescreen or 16:9 TV
• When playback is completely stopped, use the “HDMI” button on the
remote control to switch the video output resolution. Select the
resolution that produces the best picture quality on your TV. For most
flat panels and DLP™, LCD or LCoS (SXRD™, D-ILA™) rear projection
televisions this will be 720p. For CRT rear projection televisions this
will likely be 1080i. For non HD displays (very rare if they have HDMI
or DVI) this will be 480p.
• If the HDMI input of your TV is only capable of decoding 2-channel
digital audio, it is recommended that you set Speaker Setup Page >
Down-mix to “Stereo”. This sets the audio down-mix mode of the DVD
player to “Stereo”.
Standard Definition or 4:3 TV
If you have a widescreen (16:9) display as pictured above, select one of
these options:
• 16:9 Wide – 16:9 (widescreen) sources will be displayed in their
native aspect ratio, and 4:3 sources will be stretched.
• 16:9 Wide/SQZ – 16:9 (widescreen) as well as 4:3 sources will be
displayed in their native aspect ratio. Please note that in this mode
4:3 sources will be displayed with black borders on both sides to
maintain the correct 4:3 aspect ratio.
Important: If you are using a plasma or widescreen CRT display you
will want to avoid leaving black bars on the screen for any length of
time as you may encounter temporary burn-in where the display
retains memory of the “used” part of screen and the unused (black
bar) portions are clearly defined on the screen during subsequent
viewing sessions. The “16:9 Wide” mode is the best choice for these
types of displays.
4
DVD89
Use the best available audio connection
Connections for most CD or DVD playback
Rear Panel
Off
Connect ONE of these digital
GOOD
BEST
audio cables: Coaxial
S/PDIF or Optical S/PDIF
Audio In
Coaxial In
Speaker Setup Page > Downmix* settings:
Left/Right, Stereo, V.Surr, 5.1CH *does not
affect digital player outputs.
Optical In
AV Receiver/Integrated Amplifier
azur 640R
AV Receiver
Volume
EQ Type
None
Off
Raw
48K
00
Sound Field
SPDIF Output
LPCM Rate
Audio Tone
Analog
Stereo Direct
DVD
Video
1
Video
2
Recorder
1
Aux
CD
Recorder
2
7.1 Direct
Mute
Tuner FM/AM
Video
3
L
Audio
R
Video
S-Video Optical
Standby
/
On
Phones
–
Tuning
+
Mode/Store
Digital Processing Options
Pro Logic II
Dolby Digital Setup
HDMI Audio
Audio
Input Type
Stereo
Modes
Pro Logic/Neo/ Dolby Digital/
DSP Surround DTS Surround
Video
Input Type
Modes
Modes
On
If at all possible you will want to connect audio using digital cables
(either coaxial S/PDIF or optical S/PDIF). If your receiver or integrated
amplifier does not have Dolby Digital or DTS capability (for instance, an
older Pro Logic model) then you should connect the “Mixed” stereo
output of the DVD89 player to your receiver or integrated amplifier (and
immediately start saving for an upgrade!) Setting up, you have the
following choices:
Audio Setup Page > SPDIF Output* settings:
Raw, PCM *does not affect analogue player
outputs
Manufactured under license from Dolby Laboratories. “Dolby” and the
double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS
Digital Out” are trademarks of Digital Theater Systems, Inc.
• No Surround Speakers: If the audio system does not have surround
speakers, please use the analogue RCA-style cables and set the
Speaker Setup Page > Down-mix to “Stereo” or “V. Surround”.
• Surround, But No Dolby Digital or DTS Support: If the audio system
has surround speakers and Dolby Pro Logic Surround support, please
use the analogue RCA-style cables set the Speaker Setup Page >
Down-mix to “Left/Right”.
• Surround Speakers and/or DTS and/or Dolby Digital Support: If your
receiver supports Dolby Digital and/or DTS then please use a digital
coaxial or optical cable and set the Audio Setup Page > SPDIF Output
to “Raw”. No additional audio cables will be needed unless you listen
to SACD (see opposite).
5
Connections for non-Dolby Digital/DTS Receivers, DVD-Audio and SACD
SACD or DVD-Audio playback
To utilize SACD or DVD-Audio you will also need to connect six (6)
analogue RCA-style cables from the DVD89 player to your receiver’s
multi-channel analogue inputs. These multi-channel outputs will also
support playback of DVD-Audio, DTS, Dolby Digital and stereo sources.
Here are some general notes and guidelines to following depending
upon what formats you intend to play:
Rear Panel
L
R
C
SL
SR
SW
SBL/SB
SBR
azur 640R
AV Receiver
Volume
Analog
Stereo Direct
DVD
Video
1
Video
2
Recorder
1
Aux
CD
Recorder
2
7.1 Direct
Mute
Tuner FM/AM
Video
3
L
Audio
R
Video
S-Video Optical
Standby
/
On
Phones
–
Tuning
+
Mode/Store
Digital Processing Options
Audio
Input Type
Stereo
Modes
Pro Logic/Neo/ Dolby Digital/
DSP Surround DTS Surround
Video
Input Type
Modes
Modes
AV Receiver/Integrated Amplifier
Dolby Pro Logic receivers
If you have an older Dolby Pro Logic surround receiver that does not
support Dolby Digital or DTS but has multichannel inputs, you will want
to connect the 6 analogue outputs of the DVD89 player to the analogue
multichannel inputs of your receiver. To do this you must:
• Use six (6) analogue RCA-style cables and set the Speaker Setup
Page > Down-mix to “5.1CH”.
• Enable or select the multi-channel analogue inputs on your receiver.
This is absolutely worth it if you haven’t yet upgraded your receiver. Truly
discrete audio channels are a wondrous thing, so enjoy them if you can.
6
DVD89
Setting up the player: Advanced
General setup page
Setup menu options
The following is an advanced tour of the Setup Menu options which
enables control over how your DVD player functions in various situations
and with various program material and hardware. The DVD89 player
comes with a “safe” default configuration, so you should get
performance out of your player even if you don’t touch the Setup Menu
system. For those of you wanting to understand more and really tweak
your settings, read on…
Entering the setup menu system
1. Press the SETUP button on the remote control, and the TV screen
displays: 10 SETUP
1. TV Display: This is a primary setting and is addressed in the Setting
up the player: Basics section. To set the aspect ratio of the DVD
player’s output image to match your TV, select from the following:
• 16:9 Wide – 16:9 (widescreen) sources will be displayed in their
native aspect ratio, and 4:3 sources will be stretched.
• 16:9 Wide/SQZ – 16:9 (widescreen) as well as 4:3 sources will be
displayed in their native aspect ratio. Please note that in this mode
4:3 sources will be displayed with black borders on both sides to
maintain the correct 4:3 aspect ratio.
Setup
• 4:3 Pan/Scan – 4:3 TV Pan and Scan. Choose when the display is 4:3.
Both sides of a widescreen image are clipped (you lose about 30% of
the picture).
2. Press the LEFT/RIGHT ARROW buttons to select the setup page.
There are 5 pages: General Setup, Speaker Setup, Audio Setup,
Video Setup, and Preference. Press the SELECT button to enter the
selected setup page. The Preference page can only be accessed
when playback is completely stopped, or when there is no disc in the
player.
• 4:3 Letterbox – 4:3 TV Letterbox. Choose when the display is 4:3.
Widescreen image is displayed in “letterbox” format with black
borders on top and bottom (preferred).
TV Screen Appearance
4:3
DVD Content
16:9
Pan-Scan
Letterbox
Wide
Wide/SQZ
3. Press the UP/DOWN ARROW buttons to select the setup item to be
changed, and press the SELECT button to change the setting. Grayed-
out setup items cannot be changed. To allow changing of such items,
make sure the item is applicable, that playback is completely
stopped, and/or there is no disc in the player. For example, in the
Video Setup Page (below), you may use the UP/DOWN ARROW
buttons to select the “Contrast” setup item, and press the SELECT
button to change the “Contrast” setting.
4:3
16:9
2. OSD Lang (English): English is the only available language for the US
version of this player.
3. Screen Saver (on/off): To turn on/off the screen saver function. When
the screen saver is on, a moving logo will appear instead of the static
image after 2 minutes of inactivity. This is designed to minimize the
burn-in issue for plasma and CRT display devices.
4. Angle Mark (on/off): To turn on/off the display of angle mark when
DVD content with multiple available angles is played.
4. To select a value from the list of available settings, press the
UP/DOWN ARROW buttons and then press the SELECT button to
confirm.
5. SACD Priority: To select which audio tracks to play for SACD (Super
Audio CD). The options are:
5. To exit the SETUP menu, press the SETUP button on the remote
control.
• Multi-Channel – Play the multi-channel surround audio
• 2-Channel – Play the 2-channel stereo audio
• CD MODE – Play the CD layer of a hybrid SACD disc
6. DVD-Audio Mode: To select which portion of a hybrid DVD-Audio disc
to playback. The options are:
• DVD-Audio – Play the DVD-Audio portion of the disc with surround
audio
• DVD-Video – Play the DVD-Video portion of the disc with Dolby Digital
or DTS audio
7
Speaker setup page
4. Rear Speaker: To set the sound filtering control for the rear speakers.
The options are:
• Large – Choose if the rear/surround speakers are full range
(reproduce down to at least 40Hz) and if you do not have a subwoofer.
Bass frequencies are passed to the rear speakers.
• Small – Choose if the rear/surround speakers are not “full range”
speakers (almost all speakers qualify to be “small”). Bass frequencies
are not passed to the rear speakers to reduce possible distortion.
• Off – Choose if there are no rear speakers. This sends Rear Speaker
information to the Front Speaker outputs.
1. Down-mix Mode: This sets the audio down-mix mode to convert multi-
channel audio into twochannel output. This setting only affects the
“Mixed L/R” analogue audio outputs. The options are:
5. Subwoofer: To enable/disable the Subwoofer output. The options are:
• On – Subwoofer output is enabled.
• Left/Right - Left and Right channels only. This mode is intended for
use with two-channel Dolby Pro Logic receivers. If the content is
encoded with Dolby Pro Logic then the encoded audio will be correctly
preserved and passed to the receiver for Dolby Pro Logic processing.
For stereo content the output will be stereo.
• Off – Subwoofer output is disabled.
6. Channel Delay: This feature, which is displayed in inches, sets the
delay time for the Center and Rear speakers as well as the Subwoofer.
The delay is to compensate for differences between the distance of
the Front speakers to the listening position, and the distances
measured by the other speakers in the system (Center, Surrounds
and Subwoofer).
• Stereo - This mode down-mixes decoded multi-channel (5.1ch) audio
to 2-channel stereo output. For stereo content the output will be
stereo. For multi-channel content the surround and center channels
will be mixed with the left and right front channels. Recommended for
use with TV sets or stereo receiver/amplifiers.
• V. Surround - Virtual Surround. This mode creates a virtual surround
effect from stereo or multi-channel audio contents.
• 5.1CH – This mode enables 5.1ch decoded analogue audio output.
The number of actual output channels depends on the disc. Note: For
multi-channel content, only the left front and right front channels will
be re-produced from the Down-mix outputs. If you are using two
speakers and don’t hear dialogue or vocals, double check that this
mode is not engaged.
• Measure the distance (in inches) from the primary listening position
to the Front Left Speaker. This is your baseline measurement – the
primary distance that will determine the adjustments for your system.
Your Front Right and Left speakers should measure the same
distance. If they do not, please adjust them if possible.
Analogue multi-channel output settings
The following settings only affect the analogue multi-channel outputs,
not the digital coaxial or optical outputs of the DVD player. We
recommend using the analogue multi-channel outputs of this player only
when you are playing SACD or DVD-Audio discs and/or cannot utilize
HDMI or the digital audio outputs with your audio system.
2. Front Speaker: To set the sound filtering control for the front
speakers. The options are:
• Large – Choose if the front speakers are full range (reproduce down
to at least 40Hz) and if you do not have a subwoofer. Bass frequencies
are passed to the front speakers.
• Small – Choose if the front speakers are not “full range” speakers
(almost all speakers qualify to be “small”). Bass frequencies are not
passed to the front speakers to reduce possible distortion. This is the
preferred setting for all systems utilizing a subwoofer.
3. Center Speaker: To set the sound filtering control for the center
speaker. The options are:
• Large – Choose if the center speaker is full range (reproduces down
to at least 40Hz) and if you do not have a subwoofer. Bass frequencies
are passed to the center speaker.
• Small – Choose if the center speaker is not a “full range” speakers
(almost all center channels qualify to be “small”). Bass frequencies
are not passed to the front speakers to reduce possible distortion.
This is the preferred setting for all systems utilizing a subwoofer.
• Off – Choose if there is no center speaker. This sends Center Speaker
information to the Front Speaker outputs.
8
DVD89
Speaker setup page continued
• Press the UP/DOWN ARROW buttons to select the first speaker to
configure.
Example channel delay adjustment:
Supported configuration
• Measure the distance (in inches) from that speaker to the listening
position. If it is LESS than the distance to the Front Left speaker, enter
the difference (as close as possible) in inches using the LEFT/RIGHT
ARROW buttons. If it is GREATER than the distance to the Front Left
speaker, then leave the value at 0.
• Repeat for each speaker in the system (Center, Left Surround, Right
Surround, and Subwoofer) as available.
• Press the SELECT button to confirm the settings and return to the
Speaker Setup Page.
• If the distance between the listener and the front speakers are 60
inches, and the distance between the listener and the left surround
speaker is 80 inches, the distance difference is 20 inches.
• This DVD player does not support delays for when the distance
between the center or surround speakers and the listener are shorter
than that between the front speakers and the listener.
Settings:
Center Speaker – 4 Inches
Subwoofer – 4 Inches
• In case the channel delay settings cannot match your speaker
configuration, please set all distance difference to 0 inch and use
your receiver/amplifier to set the channel delay (if possible).
Left Surround – 12 Inches
Right Surround – 12 Inches
7. Channel Trim: To set the volume of each individual channel.
Unsupported configuration
• Press the LEFT/RIGHT ARROW buttons to select the channel to be
adjusted.
• Press the UP/DOWN ARROW buttons to raise or lower the volume of
the selected channel in 0.5dB increments.
• Press the SELECT button to confirm the settings and return to the
Speaker Setup Page.
Settings:
Center Speaker – 0 Inch
Subwoofer – 0 Inch
Left Surround – 0 Inch
Right Surround – 0 Inch
9
Audio setup page
6. Pro Logic II: Taking a step further than most DVD players, the OPPO
DVD player allows you to configure Dolby Pro Logic II to expand 2-
channel source audio into full 5-channel surround sound. Note: Pro
Logic II functionality is effective only when Speaker Setup Page >
Down-mix is set to “5.1ch” and SPDIF Output is set to “Raw”.
• Press the SELECT button to enter the Pro Logic II Config page.
• Press the LEFT ARROW button to exit the Pro Logic II Config page.
1. EQ Type (None/Rock/Pop/Live/Dance/Techno/Classic/Soft): This
sets a corresponding equalization pattern type to the current music
track. Note: These EQ options are not available for SACD, DTS or DVD-
Audio tracks.
2. Sound Field (Off/Concert/Living/Room/Hall/Bathroom/Cave/Arena/Church):
These allow users to engage fun sound field effects that will alter the
original audio presentation as it was intended. Note: These EQ
options are not available for SACD, DTS or DVD-Audio tracks.
A. Pro Logic II: To turn on or off the Pro Logic II processing. The options
are:
3. SPDIF Output: This set the bit stream type of the digital audio output
for use with Dolby Digital and DTS-compatible receivers. The options
are:
• On – Pro Logic II processing is always on
• Off –Pro Logic II processing is disabled
• Raw – Passes the encoded multi-channel digital audio unaltered.
Choose this setting if your receiver/amplifier is capable of decoding
Dolby Digital and/or DTS.
• Auto – Pro Logic II processing is on only when Dolby Pro Logic II
encoded content is detected.
• PCM – Forces down-mixed 2-channel digital audio output. Choose this
setting if your receiver/amplifier only supports stereo digital (PCM)
audio.
B. Mode: To set the processing mode of Pro Logic II. The options are:
• Music – The surround experience is tailored for multi-channel music
playback
4. LPCM Rate: To set the maximum Linear PCM output frequency. The
options are:
• Movie – Emphasis is given to the center channel as two-channel audio
is decoded and played back into your 5.1 system
• 48K – Supported by most equipment.
• Pro Logic – This activates decoding and processing of the original
Dolby Pro Logic processing with mono-surround channel. We
recommend using the Dolby Pro Logic Movie mode in lie of this 4-
channel surround format.
• 96K – Allows a higher sampling rate and frequency response. Ensure
that the receiver/amplifier can support it.
• 192K – Allows the highest sampling rate and frequency response.
Ensure that the receiver/amplifier can support it and that your dogs
are safely away from the listening area.
• Auto – Automatically selects processing mode based on the input
format
Note: The LPCM rate is selectable only when HDMI Audio is turned off.
C. Panorama (Music mode only): Turns on/off panorama mode. When
turned on, the front stereo audio is partially fed into the surround
channels for an enveloping effect.
5. Audio Tone (+/-16): This function raises or lowers the tone (key/pitch)
of the audio track. This is useful for playing Karaoke discs and should
not be used for regular music listening or movies.
D. Dimension (Music mode only): Allows gradual adjustment of the
soundfield either towards the front or towards the rear. This is useful
in setting a more even balance from all speakers with some rooms.
• Press the SELECT button to show the tone control window.
• Press the LEFT/RIGHT ARROW buttons to lower or raise the
tone/pitch.
E. Center Width (Music mode only): To control the width of the center
channel sound effect by blending the center speaker to the left and
right speakers. As the level number increases, the center channel
sound moves toward the left and right speakers.
• Press the SELECT button to confirm the setting.
10
DVD89
Audio setup page continued
Video setup page
7. Dolby Digital Setup: To configure the Dolby Digital decoder, press the
SELECT button to enter the Dolby Digital Setup page and press the
LEFT ARROW button to exit the Dolby Digital Setup page.
1. Sharpness: To set the sharpness of video output. Sharpness level can
be set with the following options:
A. Dual Mono: To choose the output for Dolby Digital discs encoded with
two independent audio channels, such as bilingual programs. The
options are:
• Sharp – Enables edge enhancement which is an artificial and picture-
degrading feature. We recommend leaving this off.
• Soft – Softens edges by smoothing the image which may cause slight
loss of details.
• Stereo – Stereo output
• L-Mono – Left channel output to both Left and Right speakers.
• R-Mono – Right channel output to both Left and Right speakers.
• Off (recommended) – Turns off edge enhancement completely.
2. Brightness: Adjusts the brightness (black level) of the video output.
• Mix Mono – Left and Right channels mixed to both Left and Right
speakers.
• Press the SELECT button to show the Brightness scale, and then use
the LEFT/RIGHT ARROW buttons to adjust.
B. Dynamic: To set the Dynamic Range Compression (DRC). DRC can
smooth out the sonic peaks and valleys common with wide-range
digital audio. Increasing DRC may make low level audio more audible
during low-level listening. Decreasing or turning off DRC restores the
sonic energy present in the original recording.
• Press the SELECT button to confirm the new setting.
3. Contrast: Adjusts the contrast (white level) of the video output.
Important: The ability to set brightness and contrast is no small thing.
If you do not have the correct black and white levels then your images
can appear washed out or you won’t be able to see into the shadows
when watching darker scenes in movies. Televisions have brightness
(black level) and contrast (white level) controls; however it may take a
combination of tweaking both the DVD player and your television to
get just the right result. We recommend using a calibration DVD like
AVIA Guide to Home Theater or Digital Video Essentials and setting
your display for the best possible picture. Once that is done, see if the
DVD player settings can get even closer.
8. HDMI Audio: Turns the audio output from the HDMI port on or off.
A. Multi-Channel – Digital audio output via HDMI will be multi-channel
PCM format (HDMI 1.1 audio). The Down-mix setting in the “Speaker
Setup Page” will affect whether and how multichannel audio content
will be down-mixed to stereo. When this option is selected,
compressed audio bit streams will decoded by the DVD player.
B. SPDIF – Digital audio output via HDMI will be the same as the SPDIF
(digital coaxial/optical audio) output. The SPDIF setting will affect
whether 2-channel PCM or raw compressed bit streams will be
carried over via HDMI. When this option is selected and SPDIF is set
to “Raw”, the TV or HDMI A/V receiver must decode compressed
audio formats. (Copyright protection on some DVD-Audio and Super
Audio CD discs may prevent audio output via HDMI with this setting.)
4. Hue: Adjusts the hue (tint) of the video output.
5. Saturation: Adjusts the saturation (color intensity level) of the video
output.
6. Gamma: Adjusts the Gamma (the actual transition from black to
white) of the video output. The available settings are High, Medium,
Low and Off.
C. Off – No digital audio output via HDMI.
7. Color Space: Selects the color space for the HDMI output. The
available options are:
• Auto (recommended) – Allows the DVD player to automatically select
the best color space based on capability information collected from
the TV display.
• YCbCr 4:4:4 – Forces YCbCr 4:4:4 color space. If you select this option
please make sure that your TV is configured to accept YCbCr 4:4:4
signals, otherwise the video color will be incorrect.
• RGB – Forces RGB color space. If you select this option please make
sure that your TV is configured to accept RGB signals, otherwise the
video color will be incorrect.
11
Preference page
6. Parental Control: Sets parental control ratings in order to prevent
minors from watching inappropriate contents. This function requires
that the disc being properly rated and encoded.
• Press the SELECT button to bring up the rating selection menu.
• Press the UP/DOWN ARROW buttons to select the rating to allow
(G/PG/PG 13/PGR/R/NC17/ADULT). The selected rating and below
will be allowed, and any rating above the selected will be blocked.
• Press the SELECT button to confirm the selection. You will be asked
for the parental control password. Enter the password (default
password: 7890) and press the SELECT button.
The Preference Page can only be accessed when playback is completely
stopped, or when there is no disc in the DVD player.
7. Password: Sets parental control password. To change the password,
enter the old password (default: 7890) and then enter a 4-digit
number as the new password. Enter the new password again to
confirm, and then press the SELECT button.
1. TV Type: Sets the output video system (PAL/NTSC) to match the type
of TV. The options are:
• Auto – No system conversion is performed. The output video system
is the same as that encoded on the disc. This requires a TV that
supports NTSC and PAL input.
• PAL – When playing PAL-encoded discs, no system conversion is
performed. NTSCencoded discs are converted to PAL output.
• NTSC (default) – When playing NTSC-encoded (Region 1) discs, no
system conversion is performed. PAL-encoded discs are converted to
NTSC output.
2. PBC (Play Back Control): Enables/disables play back control by disc
contents. The options are:
8. Default: Resets all settings to the factory default value. The parental
control password will not be reset.
• On – If the disc contains Play Back Control, follow the disc
instructions.
• Off – Play back the contents by sequence.
3. Audio: Sets the preferred audio language for DVD. If an audio track of
the selected language is available on the disc, the audio track will be
played back.
4. Subtitle: Sets the preferred subtitle language for DVD. If a subtitle of
the selected language is available, it will be displayed. When “Auto” is
selected, the subtitle display is decided by the disc.
5. Disc Menu: Sets the preferred language for displaying DVD disc
menus. If a disc menu of the selected language is available, the menu
will be shown instead of the default disc menu.
Important: If your preferred language is not listed in the Audio, Subtitle
or Disc Menu options, select “Other” and enter the Language Code
found on the Users Manual that comes with your DVD player.
12
Cambridge Audio
Gallery Court
Hankey Place
London SE1 4BB
England
Power
© 2007 Cambridge Audio Ltd
|