SPEAKER PLACEMENT
The proper placement of speakers affects how well the AV
surround system recreates the soundfield intended by the
recording engineer. Current recording practice typically
assumes a speaker array with a center channel speaker
directly in front of the central viewing position. Left and right
speakers are placed so they each form a 30 degree angle
from the centerline. Left and right surround speakers should
be 110 degrees from the centerline. Left and right rear
speakers in a 7.1 system should be at 140 degrees. If a sin-
gle rear speaker is used in a 6.1 system, it should be cen-
tered on the rear wall. Front speakers should be as close to
the height of the TV monitor as practical. Surround and rear
speakers should be slightly higher. Recreate this speaker
pattern as closely as your room and furnishings allow.
RECOMMENDED DISTANCE
APART FOR STEREO
APPROX.
EAR LEVEL
20 - 55
ANGLE
Don’t be too concerned if your situation and listening envi-
ronment dictate the speakers’ position. Most rooms do not
allow ideal placement. Place your speakers as close to
these guidelines as practical. The speakers will still provide
convincing, lifelike sound.
MAXIMUM RECOMMENDED DISTANCE
APART FOR HOME THEATER
MAIN SPEAKERS
Your surround processor has a variety of adjustments to
optimize the sound based on the speakers’ capabilities and
placement. These adjustments vary by processor, so refer
to your processor’s manual for instructions specific to your
equipment. Set your main, center, and surround settings to
“SMALL”, with subwoofer “ON”. If your processor allows you
to adjust the crossover frequency, set it as close to 100Hz
as possible.
MAIN
SPEAKER
MAIN
SPEAKER
CENTER CHANNEL
LEVEL
SURROUND
SPEAKER
SURROUND
SPEAKER
WITH
CENTER
SPEAKER
POWERED
SUBWOOFER
7.1 REAR
SPEAKER
7.1 REAR
SPEAKER
• Avoid placing front left and right speakers very close to a
side wall (within 12-14 inches). The reflected sound from the
wall degrades the sound coming directly from the speaker.
3
WIRING THE SPEAKERS
If you wish to conceal the wire within the walls, it is easiest
to run the wires to their final positions prior to mounting the
speakers.
The spring loaded terminals of the MC650HD accept bare
wire between AWG #12 and AWG #18 (lower numbers are
thicker). It is not necessary to “tin” the wire or use connec-
tors to terminate the wire.
• Use at least AWG #18 speaker cable for short runs
(under 15 feet). Use AWG #16 or heavier speaker cable
for longer runs.
Strip 1/2 inch
• Building codes typically require plenum rated wire for
installation within walls. Be sure to use wire that complies
with any applicable local building codes. Plenum rated
cable typically has an outer jacket with individually
insulated conductors inside the outer jacket. Some brands
of plenum rated cable may be too thick to fit the space
between the wall mount bracket and the speaker. To use
heavier plenum rated speaker cable with the wall mount
brackets, remove the outer jacket and any filler cord back
to the point where the wire exits the wall.
Preparing the wires:
1. Determine how long the speaker cable should be for
each speaker. Cut the speaker cable into the
appropriate lengths.
2. Route the wire to each speaker location.
3. Strip 1/2 inch of insulation from the two individual
conductors in the speaker cable. Twist the exposed
strands of bare wire together.
4. Determine which conductor you will use to connect the
positive terminals of the amplifier and speaker together.
Printing or a ridge on the insulation usually distinguishes
one of the two conductors. Sometimes the metal of the
conductors has two different colors, or the insulation
color of each conductor may be different.
4
TO ATTACH THE WIRES
1. Press the speaker’s red terminal to expose the hole in
its shaft.
2. Insert the stripped end of one cable’s positive conductor
into the speaker’s red (+) terminal.
3. Release the terminal to secure the connection. Make
sure no stray strands of wire are present.
4. Repeat the procedure for the cable’s other conductor
and the speaker’s black (–) terminal.
5. Connect the opposite end of the speaker cable to the
speaker outputs of your receiver. Remember to
observe channel and polarity (Left Positive, Left
Negative, Right Positive, Right Negative).
6. Repeat the process for each speaker.
5
SPEAKER MOUNTING
The MC650HD may be wall mounted or placed horizontally
on a table top as a center-channel using the included
hardware. Matching floor and table-top stands are available
separately from Cambridge SoundWorks.
Hanging the speaker on the wall:
4.
The MC650HD may be mounted either vertically or
horizontally using the supplied wall bracket. Method #1 is
recommended. Use Method #2 if there is insufficient
clearance for Method #1.
Method #1 – Use this method when mounting the speaker
vertically when you have at least 21" clearance above the
top of the wall mount bracket. Use this method whenever
mounting the speaker horizontally.
1.
1. Using the wall mount bracket as a guide, mark at least
four locations for mounting screws. It is best to use the
holes at the four outermost corners. If concealing the
wiring in the wall, position the bracket so that the wire
exits the wall through the large hole in the center of the
bracket. The wire should extend through the bracket
approximately 12". Drill a 1/4" diameter hole and install
wall anchors in each location. Refer to the instructions
in the Appendix for proper use of the Toggler brand
anchors included with this speaker.
3.
5.
2.
2. Attach the mounting bracket securely to the wall using
four #10 screws.
Note: Screw is already
installed within speaker.
Use philips screwdriver
to tighten. (See #4)
3. Attach the wire to the speaker terminals. Slide the
speaker on the bracket from the top while guiding the
wire through the channel between the speaker and
bracket.
4. Pull the speaker logo straight out to remove it. Use a
philips screwdriver to gently tighten the lock screw
concealed in the hole behind the logo to secure
speaker to the bracket. Do not over-tighten. It only
requires slight pressure! Pay attention to the wire
location so that the screw does not penetrate the
speaker wire. Install the logo so that the text is upright.
6
SPEAKER MOUNTING
Method 2 – Use this method to mount the speaker vertically
when you have less that 21" clearance above the top of the
speaker bracket. Always use method #1 when mounting the
speaker horizontally, and whenever at least 21" clearance is
available.
1. Using the wall mount bracket as a guide, mark at least
four locations for mounting screws in the elongated
keyholes found at the four corners and center sides.
It is best to use the holes at the four outermost corners.
If concealing the wiring in the wall, position the bracket
so the wire exits the wall through the large hole in the
center of the bracket. The wire should extend
approximately 12".
2. Drill a 1/4" diameter hole and install plastic anchors in
each location. Refer to the instructions in the Appendix
for proper use of the Toggler brand anchors included
with this speaker.
3. Insert #10 screws in each anchor and tighten them until
they extend approximately 1/4". Temporarily place the
bracket in place and tighten the four mounting screws
to the point that the bracket can still be be removed.
You should have to supply slight pressure to slide the
bracket back into place between the wall and screws.
4. Pass the wire through the center hole of the bracket.
Attach the wire to the speaker terminals. Slide the
speaker on the bracket from the top while guiding the
wire through the middle of the channel formed between
the speaker and bracket.
5. Pull the speaker logo straight out to remove it. Use a
philips screwdriver to gently tighten the lock screw
concealed in the hole behind the logo to secure the
speaker to the bracket. Do not over-tighten. It only
requires slight pressure! Pay attention to the wire
location so that the screw does not penetrate the
speaker wire. Install the logo with the text upright.
Note: Screw is already
installed within speaker.
Use philips screwdriver
to tighten. (See #4)
6. Align the speaker and bracket assembly over the four
screws and press downward about 1/2" so that the
screws lock into the keyhole slots in the bracket. Guide
any slack speaker wire back into the wall as you
position the speaker.
7
HORIZONTAL PLACEMENT
To place horizontally on a tabletop or shelf:
1. Attach two rubber hook-shaped stick-on feet
symmetrically along the bottom edge of the speaker
approximately 18" apart. If you are mounting the
speaker on an uneven surface you may need to attach
the feet closer to the center. Adapt the actual position
to your needs. You may orient the speaker so that the
terminals are at either end.
2. Slide the rear support into the channel on the rear of
the speaker until it is in the approximate center of the
speaker. Orient it so the foot is along the same side as
the rubber feet you installed in step 1.
1.
3. Tighten the set-screw finger-tight to stabilize the
support.
4. Remove the logo by pulling it straight out. Turn it 90
degrees so that the text reads correctly. Press it back
in place.
3.
2.
4.
8
SETTING BASS CONTOUR
The switch located near the connection terminals optimizes
the low frequency response of the speaker for wall or stand
mounting.
•
When the speaker is mounted on a speaker stand,
away from the wall press the end of the switch marked
with “|”.
•
When the speaker is mounted on the wall or table,
press the end of the switch marked with “O”. The upper
bass range will be slightly attenuated to compensate for
the increase in bass caused by wall reflection.
The above recommendations should yield the most accurate
response in each example, but they are optional. If you pre-
fer the sound with settings opposite the above recommen-
dations, feel free to use your settings instead.
Automatic Tweeter Protection
he MC650HD can be safely used with any receiver rated
above 30 watts per channel. There is little advantage in
using more power than 100 watts per speaker, but receivers
above this power rating can be used so long as the receiver
is not operated at distorted levels.
To protect the tweeter, a self-resetting circuit breaker is
incorporated into the MC650HD crossover network. If the
speaker is overpowered for an extended period, this circuit
breaker will open and the tweeter will be disconnected.
When the volume is reduced or the overload has passed,
the circuit will reset and normal operation will be restored.
9
SPECIFICATIONS
Appendix
Warning About Excessive Amplifier Distortion:
®BRAND
Operating a receiver (of any power rating) beyond its
maximum undistorted output level creates distortion –
added high frequency sound not part of the musical program.
Distortion dramatically increases the internal operating tem-
perature of a speaker and will eventually cause the speak-
er’s failure due to burned or melted internal parts. While
Cambridge SoundWorks includes the most heat-tolerant
parts commensurate with good acoustic design, the
speaker’s Limited Warranty against defects in materials or
workmanship does not apply to parts that fail from long-
term operation at very high temperatures.
TM
®
AF6 ALLIGATOR
Solid-Wall Anchors
1
1/4"
Drill 1/4" diameter hole — minimum hole
depth 1 /2". Insert anchor and tap flush.
1
2a
Enclosure Cleaning
Place item over anchor. Insert screw and
tighten flush. For best results use screw
gun for installation in solid walls.
The speaker enclosures can be cleaned with a soft, damp
cloth or mild cleaner.
2b
Brush or vacuum the grille panels with a soft brush
attachment to your vacuum cleaner.
In walls of minimum thickness 3/8",
screw opens anchor and locks securely.
Patented under U.S. Patent Nos. 4,752,170 and
5,161,296; and foreign counterparts thereof.
Other patents pending. TOGGLER and typeface,
and ALLIGATOR are worldwide registered
trademarks of Mechanical Plastics Corp.
© 2002 MPC
Specifications
Dimensions: 25-3/8" H x 7-1/8" W x 3-15/16" D
Weight: 14-1/2 pounds each
Impedance: nominal 8 ohms
Recommended amplifier power range: 20W – 100W RMS
per channel.
Frequency Range: 80Hz – 24kHz.
Woofer Type: 4 x 3-1/2" with co-injection molded composite
cones and butyl-rubber surrounds.
Tweeter Type: 1/2" aluminum dome with ferrofluid-damping
and neodymium magnet.
Crossover: 2-1/2 way, series-connected with selectable
wall-mounting compensation.
Enclosure: High-density pressure-cast aluminum with
molded-composite baffle.
10
WARRANTY
LIMITED WARRANTY
Cambridge SoundWorks,® a Creative company, warrants the
following Cambridge SoundWorks
6.Any product purchased outside the U.S.A., its
possessions or territories.
products for the periods indicated:
Who may enforce the warranty:
Loudspeakers for interior use without active amplifiers:
5-year parts and labor from the product’s Date Of Purchase
(DOP) from an authorized Cambridge SoundWorks retailer.
This warranty may only be enforced by the original purchaser.
WHAT CAMBRIDGE SOUNDWORKS, USA WILL PAY FOR:
We will pay for all labor and material expenses for items
covered by the limited warranty. Payment of shipping charges
is discussed in the next section of this limited warranty.
Powered Subwoofers for interior use:
5-year limited parts and labor warranty on speaker ele-
ments, passive circuitry and cabinet workmanship from
DOP. 2-year limited parts and labor warranty on the active
amplifier circuitry from DOP.
How You Can Get Service:
1. If you feel your unit needs service, contact Cambridge
SoundWorks Return Authorization by calling toll-free (800)
367-4434. If we agree service is required, we will provide
you with a Return Authorization number. Please do not
return your unit to the factory prior to obtaining a Return
Authorization.
Loudspeakers for exterior use:
1-years parts and labor from the product’s DOP from an
authorized Cambridge SoundWorks retailer.
®
®
®
PCWorks, SoundWorks, and MicroWorks PC/
Multimedia speaker systems:
1-year limited parts and labor warranty from DOP from an
authorized Cambridge SoundWorks retailer.
2. You must pay any shipping charges to Cambridge
SoundWorks. For repairs that are covered by this Warranty,
Cambridge SoundWorks will pay the return shipping
charges to any destination within the fifty United States.
®
SoundWorks High Performance Table Radios and other
electronics:
Limitation of implied warranties:
All implied warranties, including warranties of merchantability
and fitness for a particular purpose, are limited in duration to
the length of this warranty.
1-years parts and labor from the product’s DOP from an
authorized Cambridge SoundWorks retailer.
What is covered and what is not covered:
Except as specified below, this warranty covers parts and
labor to correct all defects in materials and workmanship.
The following are not covered by the warranty:
Exclusion of damages:
Cambridge SoundWorks, USA’s liability for any defective
product is limited to repair or replacement of the product at
Cambridge SoundWorks, USA’s option. Cambridge
SoundWorks, USA shall not be liable for damage to other
products caused by any defects in Cambridge SoundWorks
product, damages based upon inconvenience or loss of use
of the product, or any other damages, whether incidental,
consequential, or otherwise.
1.Damage, deterioration, malfunction or failure to meet
performance specifications resulting from:
a. Accident, acts of nature, misuse, abuse, neglect or
product modification.
b. Improper installation, removal or maintenance, or failure
to follow instructions supplied
with the product.
c. Repair or attempted repair by anyone not authorized
by Cambridge SoundWorks
to repair the product.
d. Any shipment of the product (claims must be presented
to the carrier).
How state law relates to the warranty:
Some states do not allow limitations on how long an implied
warranty lasts and/or do not allow the exclusion or limitation
of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
e. Any cause other than a product defect.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
2.Cleaning, initial setup, checkups with no defects found, or
charges incurred for installation, removal or reinstallation
of the product.
This warranty is enforceable only inside the U.S.A., its
possessions or territories.
3.Any product on which any serial number has been
defaced, modified, or removed.
Cambridge SoundWorks, Inc.
120 Water Street
4.Batteries.
5.Accessories, including but not limited to batteries, cables,
mounting hardware and brackets, cleaning accessories,
antenna and detachable power cords.
North Andover, MA 01845
1-800-FOR-HIFI
11
P81-2190
|