EF100mm f/2.8L MACRO IS USM
ENG
Instruction
a Safety Precautions
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Do not make any changes or modifications to the equipment
unless otherwise specified in the instructions. If such changes or
modifications should be made, you could be required to stop
operation of the equipment.
This equipment has been tested and found to comply with the
limits for class B digital device, pursuant to part 15 of the FCC
Rules. hse limits are designed to provide reasonable protection
nst hamful interference in a residential installation. This
ment generates, uses and can radiate radio frequency
ergy and, if not installed and used in accordance with the
instuctions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
a Safety Precautions
• Do not look at the sun or a bright light source
through the lens or camera. Doing so could result
in loss of vision. Looking at the sun directly through
the lens is especially hazardous.
• Whether it is attached to the camera or not, do
not leave the lens under the sun without the
lens cap attached. This is to prevent the lens from
concentrating the sun’s rays, which could cause a
fire.
Handling Cautions
• If the lens is taken from a cold environment in
a warm one, condensation may develop on the
lens surface and internal parts. To preven
condensation in this case, first put the lens into an
airtight plastic bag before taking it from a cold to
warm environment. Then take out the lens after it
has warmed gradually. Do the same when taking
the lens from a warm environment into a cold one.
• Do not leave the lens in excessive heat such as in
a car in direct sunlight. High temperatures can
cause the lens to malfunction.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for
help.
This Class B digital apparatus complies with Canadian ICES-003.
ENG-2
Nomenclature
Distance scale (→ 6)
Focusing distance range selection switch (→ 5)
Hood mount (→ 7)
Rubber ring (→ 4)
Contacts (→ 4)
Filter mounting
thread (→ 14, 15)
Focusing ring (→ 5)
Lens mount index (→ 4)
Focus mode switch (→ 5)
Tripod mounting location (→ 13)
Image stabilizer switch (→ 10)
For detailed information, reference page numbers are provided in parentheses (→ **).
ENG-3
1. Mounting and Detaching the Lens
See your camera’s instructions for details on
mounting and detaching the lens.
The lens mount has a rubber ring for enhanced
water- and dust-resistance. The rubber ring may
cause slight abrasions around the camera's lens
mount, but this will not cause any problems. If the
rubber ring becomes worn, it is replaceable by a
Canon Service Center at cost.
• After detaching the lens, place the lens with the
rear end up to prevent the lens surface and
electrical contacts from getting scratched.
• If the contacts get soiled, scratched, or have
fingerprints on them, corrosion or faulty
connections can result. The camera and ens
may not operate properly.
• If the contacts get soiled or have fingerprints on
them, clean them with a soft cloth.
• If you remove the lens, cover it with the dust
cap. To attach it properly, align the lens mount
index and the
K
index of the dust cap as shown
in the diagram, and turn clockwise. To remove it,
reverse the order.
ENG-4
2. Setting the Focus
Mode
3. Switching the Focusing
Distance Range
To shoot in autofocus (AF) mode, set the focus
mode switch to AF.
To use only manual focusing (MF), set the foc
mode switch to MF, and focus by turning the
focusing ring. The focusing ring always works
regardless of the focus mode.
can witch the focusing distance range to
oe of three settings: FULL (0.3 m/1.0 ft. to
nfinity), 0.3 m/1.0 ft. to 0.5 m/1.6 ft., or 0.5 m/1.6
ft. to infinity.
By setting the suitable focusing distance range,
the actual autofocusing time can be shorter.
After autofocusing in ONE SHOT AF mode, focus
manually by pressing the shutter button halfway
and turning the focusing ring. (Full-time manual
focus)
ENG-5
4. Infinity Compensation Mark
Infinity compensation mark
Distance index
To compensate for shifting of the infinity focus
point that results from changes in temperature.
The infinity position at normal temperature is the
point at which the vertical line of the L mark i
aligned with the distance indicator on the
distance scale.
For accurate manual focusing of subjects at
infinity, look through the viewfinder or look at the
magnified image* on the LCD screen while
rotating the focusing ring.
* For cameras with Live View shooting capability.
ENG-6
5. Hood
The ET-73 hood can keep unwanted light out of the lens, and also protects the lens from rain, snow,
and dust.
To attach the hood, align the hood’s attachment posimark with the red dot on the front of the
lens, then turn the hood as shown by the arrol te lens' red dot is aligned with the hood's stop
position mark.
The hood can be reverse-mounted on the lens for storage.
• Part of the picture may be blocked if the hood is not attached properly.
• When attaching or detaching the hood, grasp the base of the hood to turn it. To prevent deformation, do not
grasp the rim of the hood to turn it.
• Remove the hood when using the macro flash.
ENG-7
6. Picture Taking
Normal Photography
The lens can be used as a medium-telephoto
Since macro shots have a very shallow depth of
field, focus carefully to obtain proper sharpness.
lens for normal photography such as portraits.
• The magnification refers to the ratio between the
subject’s size and the corresponding image size
on the focal plane. On the distance index, it is
indicated as 1:x.
• To check the depth of field, press the camera's
dpth-of-field preview button.
Closeup Photography
Close-up photos up to 1x (life-size) magnification
are possible. The minimum focusing distance of
30 cm is the distance from the subject to the
focal plane. The working distance from the front
of the lens to the subject is about 14 cm.
For normal close-up shooting, the higher the
magnification, the faster the shutter speed mu
be to prevent blur caused by camera shke.
Although it depends on the shooting conditions,
usually the shutter speed must be at least one or
two stops faster than normal.
For a shooting magnification of 0.5x, this lens
provides the effect of a shutter speed faster by
about three stops. For 1x, it will be about two
stops faster.*
* Depending on shooting conditions.
ENG-8
7. About Exposure
When you use a handheld exposure meter to set
the exposure, you must take into account the
exposure factor shown in the following table.
Setting the Exposure
When taking photographs using TTL metering,
no exposure compensation is necessary to meter
the light coming through the lens.
With TTL metering, AE (autoexposure) is
possible at all focusing distances. Just set the
desired picture-taking mode, then check the
shutter speed and aperture before taking the
picture.
Magnification
Effective f/No.
Exposure Factor
(stops)*
1 : 5 1 : 3 1 : 2 1 : 1.5 1 : 1
3.6
4.1
+1
+1
4.6
5.0
5.9
+2
+2
2
3
+
+1 13 +1 23
+1 12
1
2
+
* Uppr alues: 1/3 stops. Lower values: 1/2 stops.
Magnification and Effective f-
number
• The correct exposure for a close-up shot largely
depends on the subject. Therefore, try to bracket
the exposure for the same subject.
• Using aperture-priority AE (Av) or Manual (M)
picture-taking modes are recommended for
macro photography as it is easy to adjust depth
of field and exposure in these modes.
The aperture displayed by the camera asume
that the focus is set to infinity. The actua
aperture (effective f-number) becomes darker
(effective f-number increases) at closer focusing
distances (magnification increases). This does
not cause exposure problems for normal picture-
taking. However, for closeup photography, you
cannot ignore the change in the effective f-
number.
ENG-9
8. Image Stabilizer
You can use the image stabilizer in AF or MF mode.
This function provides optimal image stabilization depending on
shooting conditions (such as shooting still subjects and following
shots).
Set the STABILIZER
When ypress the
The image stabilizer in this lens is
effective for hand-held shots under
the following conditions.
1switch to
2shuttr button halfway,
.
• If you are not going to
use the image stabilizer
function, set the switch to
.
the Image Stabilizer
• Close-up shooting.
• In semi-darkened areas such as
indoors or outdoors at night.
will start operating.
• Make sure the image in
the viewfinder is stable,
then press the shutter
button the rest of the way
down to take the picture.
•
In locations where flash
photography is prohibited, such as
art museums and theater stages.
• In situations where your footing is
uncertain.
• In situations where fast shutter
settings cannot be used.
• When panning subjects in motion.
ENG-10
Image Stabilizer
• The shorter the subject distance from the
camera, the lesser the Image Stabilizer effect
will be.
• The Image Stabilizer cannot compensate for a
blurred shot caused by a subject that moved.
• When shooting a still subject, it compensates for
camera shake in all directions.
• It compensates for vertical camera shake during
following shots in a horizontal direction, and
compensates for horizontal camera shake
during following shots in a vertical direction.
• Using a tripod also stabilizes the image.
However, depending on the kind of tripod and
sooting conditions, sometimes it may be better
o urn off the Image Stabilizer function.
• Thstabilizer is equally effective for hand-held
photography and photography with a monopod.
• The image stabilizer function also operates
when the lens is used with an Extension Tube
EF12 ll or EF25 ll.
•
Set the STABILIZER switch to
when you are
taking pictures using the Bulb setting (long
exposures). If the STABILIZER switch is set to
the image stabilizer function may introduce errors.
• The Image Stabilizer may not be fully effective if
you shoot from a violently shaking vehicle or
other transportation.
• The Image Stabilizer consumes more power
than normal shooting, so fewer shots cn be
taken if you use the function.
,
•
The image stabilizer operates for about two
seconds even when your finger is off the shutter
• Pictures may look distorted after being taken
depending on the camera, but this doesn't affect
shooting.
• If you set the camera’s Custom Function to
change the assigned button to operate the AF,
the Image Stabilizer will operate when you press
the newly assigned AF button.
button. Do not remove the lens while the stabilizer
is in operation. This will cause a malfunction
• With the EOS-1V/HS, 3, ELAN 7E/ELAN
.
7/30/33, ELAN 7NE/ELAN 7N/30V/33V, ELAN
II/ELAN IIE/50/50E, REBEL 2000/300, IX, and
D30, the Image Stabilizer will not work during
self-timer operation.
ENG-11
9.Taking Hand-held Close-ups
Close-up shots are more prone to be affected by
camera shake than with normal shooting. The
Image Stabilizer's corrective effect is therefore
less during close-ups than during normal shooting
even with the same degree of camera shake.
The depth of field also becomes very shallow with
close-ups, and moving forward or back even
slightly will throw off the focus.
When hand-holding the camera for close-up
shooting, minimize camera shake and blurred
focus with the following techniques:
Place bth elbows on a steady surface such as a table.
Hold the camera firmly
As shown on the right, hold the camera irmly so
it does not move while shooting.
Use AI Servo AF
For close-up shots, set the camera's AF mode to
AI Servo AF. Using autofocus is recommended.
The AI Servo AF mode can minimize blurred
focus during close-up shooting.
Use your knee to support
an arm holding the
camera.
Lean against a steady
object like a wall.
For details, see the camera's instruction manual.
ENG-12
10. Using the Tripod Mount
(Sold separately)
Adjusting the Revolving Mount
This lens can be used with the D (B) tripod mount ring, sold separately.
You can loosen the orientation lock-knob on the tripod mount to allow it to rotate as needed to fit a
particular camera model for switching between vertical and horizontal positions.
Detaching
Use the following procedures to remove and attach the tripod mount.
Turn the locking knob
counterclockwise until it
becomes loose (about 3 turns),
and pull the knob in the direction
of the arrow to release the collar.
With the collar open,
remove the tripod mount.
To install, while pulling the
locking knob, bring the collar
to the original position, and
tighten the locking knob
securely.
Depending on the EOS camera model, if a battery pack or vertical grip is attached, the tripod mount may
bump into it. If that is the case, remove the battery pack/vertical grip or the tripod mount.
The tripod collar can be attached to or detached from the lens while the lens is attached to the camera.
ENG-13
11. Filters
(Sold Separately)
12. Extension Tubes
(Sold Separately)
You can attach filters to the filter mounting thread You can attach Extension Tube EF12 II or EF25
on the front of the lens.
II for magnified shots. The shooting distance and
magnification are shown below.
• Filters and the macro flash cannot be used on
this lens at the same time.
• If you need a polarizing filter, use the Canon
Circular Polarizing Filter PL-C B (67mm).
• To adjust the polarizing filter, first remove the
lens hood.
Camera-to-Subject
Magnification
Distance (mm)
Near
302
307
Far
1036
591
Near
1.17×
1.37×
Far
EF12 II
EF25 II
0.12×
0.27×
Manal focusing is recommended for accurate
focusing.
ENG-14
13. Macro Flash
(Sold Separately)
The Canon Macro Ring Lite MR-14EX or the
Macro Twin Lite MT-24EX enables fully automatic
macro flash photography up to 1x magnification
in E-TTL autoflash mode.
Install the Macro Lite Adapter 67 (sold
separately) on the filter mounting thread on the
front of the lens for macro flash photography.
• For information on operating the Canon Macro
Ring Lite MR-14EX or the Macro Twin Lite MT-
24EX, refer to the individual instruction booklets.
• Using aperture-priority AE (Av) or Manual (M) is
recommended.
ENG-15
Specifications
Focal Length/Aperture
Lens Construction
Minimum Aperture
Angle of View
Min. Focusing Distance
Max. Magnification
Field of View
100 mm f/2.8
12 groups, 15 elements
f/32
Diagonal: 24°
0.3 m/1.0 ft.
1 ×
Vertical: 14°
Horizontal: 20°
24 × 36 mm/0.9 × 1.4 n. (at 0.3 m)
Filter Diameter
Max. Diameter and Length
Weight
67 mm
77.7 × 123 m1 × 4.in.
625 gz.
Hood
ET-73
Lens Cap
-67UE-67 II
Case
LP1219
Tripod Collar
Ring-type tripod mounting socket D (B) (Sold separately)
• The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm to include the
E-67U lens cap and dust cap, and 24.2 mm for the E-67 II.
• The size and weight listed are for the lens only, except as indicated.
• The EF1.4X II/EF2X II extenders cannot be used with this lens. There are no compatible close-up lenses.
• Aperture settings are specified on the camera.
• All data listed is measured according to Canon standards.
• Product specifications and appearance are subject to change without notice.
ENG-16
0812Ni © CANON INC. 2009
CT1-8564-002
|