Carrier Access Network Card KTA User Manual

Adapter  
KTA Series  
User Manual  
 
1. Introduction  
KTA series is one of VoIP terminal products, with one port connecting with regular PSTN terminal devices and  
one port connecting with Internet. It transfers voice through net. By the management of soft-switch platform and  
the support of telecom, KTA can communicate with VoIP terminals and dial to regular phone inexpensively.  
KTA series’ port  
z
KTA1000’s port  
One LAN port (10 Base-T)  
One PC port (10 Base-T)  
One PHONE port (FXS)  
The relation between LAN port and PC port is not router but hub  
z
z
KTA1001’s port  
One LAN port (10 Base-T)  
One PHONE port (FXS)  
KTA1010’s port  
One LAN port (10 Base-T)  
One PC port (10 Base-T)  
One PHONE port (FXS)  
One LINE port (FXO)  
KTA1010 has HUB function  
The relation between LAN port and PC port is not router but hub  
z
KTA1011’s port  
One LAN port (10 Base-T)  
One PHONE port (FXS)  
One LINE port (FXO)  
2. Sketch  
2.1 Ports figure  
2
1
4
5
3
6
1——Power Port  
2——Setup Button  
3——PC port :(10 Base-T Ethernet) RJ45 port to connect with PC (only for KTA1000, KTA1010)  
4——LAN port:(10 Base-T Ethernet) RJ45 port to connect with Internet or Local Network  
5——PHONE Port (FXS)  
6——LINE Port (FXO) (only for KTA1010,KTA1011)  
3
 
 
2.2 LED Indicators  
Power  
TX  
RX  
Service Phone  
MSG  
Power——Power On LED  
TX——Network data being transmitted  
RX——Network data being received  
Service——Service connected (Remains illuminated when successfully logged-on to server)  
Phone——phone in operation (phone in-used when light on means working under VoIP, when light off means  
working under PSTN)  
MSG——unanswered call LED (unanswered call appeared if light on)  
2.3 Application figure  
Internet  
ISP  
Telecom  
PHONE LINE  
PC  
LAN  
Small PABX  
1
2
3
1
2
3
1
4
7
2
5
8
8
3
6
9
#
4
7
5
8
8
6
9
#
4
7
5
8
6
9
*
8
#
*
*
Instruction:KTA 1000,KTA1001 without LINE port,KTA1001,KTA1011 without PC port  
3. Installation and Setting  
3.1 Installation  
(1) Locate your KTA close to your Internet connection and a power outlet.  
(2) Plug the RJ-45 connector of the Ethernet 10/100Base-T cable into the KTA’s side input port , and plug the  
other side into a hub or switch, or wall/ground socket of the structuring cable.  
4
 
 
(3) Plug one side of the RJ-11 of phone line to the PHONE Port(FXS) of KTA, plug another side of the phone  
line into user terminal (phone, line entrance to PABX, etc.).  
(4) If you are the KTA1010,KTA1011’s user, put the phone line to the LINE Port(FXO) of KTA, you will have  
the both function of VoIP and PSTN.  
(5) Plug the accessory power-adapter into the power outlet, then connect the output-plug to power-port of the  
KTA.  
(6) Then waiting for KTA’s startup, after hearing short phone ring, KTA is now working.  
Notice: Please select different type of Ethernet Cable according to the network devices (devices connecting  
to LAN). Select Straight-through Ethernet Cable for network equipments (router, hub, etc.); Select  
Cross-over Ethernet Cable for the PC of ISP server; Select the corresponding Ethernet Cable according to  
the instructions of XDSL and Cable Modem (using Straight-through Ethernet Cable in most casts).  
3.2 Configuration  
3.2.1 Configuring Network Parameters from Telephone Handset  
Without PC,users and network technician can set parameter through ordinary phone and KTA,all those operations  
can be finished under VoIP model.  
Instrucitons for network parameter setting:  
Command Format:  
Every configuration command from your telephone handset will be similar to the following format:  
#*xxxxx#.Commands are a minimum of 3 digits. If a command is prefixed by ”#*” then the  
command is a query. If the command is prefixed by just ”#” then it is a programming command.  
Use ”##” to cancel a command.  
If the command is successful you will hear “di du”. If the command is unsuccessful you will  
hear ”du du du…”  
Common commands:  
Note: Each Command below is followed by its alphanumeric representation to make it easy to  
remember.  
Query IP Address: pick-up phone handset and key in #*047# or #*0IP#  
Set IP address: pick-up handset and key in #73847# xxx*xxx*xxx*xxx# or #SETIP#xxx.xxx.xxx.xxx#  
Enable DHCP: pick-up handset,then key in #3427# or #DHCP#  
Disable DHCP: pick-up handset, then key in ##3427# or ##DHCP#  
Reboot: pick-up handest,then key in #778# or #RST#  
Restore default settings: pick-up handset ,then key in #358# or #DLT#  
Using H.323:pick-up handset ,then key in #4323# or #H323#  
Using SIP:pick-up handset ,then key in #747# or #SIP#  
Using adjusting IP:pick-up handset,then key in #3228# or #FACT#.IP type is STATIC IP.IP  
address:192.168.1.100,Gateway IP:192.168.1.1,Subnet mask:255.255.255.0.  
Note: After performing each of the above commands the KTA will reboot. You should wait  
until your telephone rings once to indicate that the reboot process has been completed.  
Notice:DHCP is a default setting of KTA Series.  
3.2.2 Configuring Network Parameters from Web Browser  
Open your web browser and enter the IP Address that has been assigned to the KTA (if necessary  
use the “Query IP Address” command in the above section). Log-in page will be displayed. The  
default password is 1234.  
Browser, such as Microsoft Internet Explorer of Windows operating system, to set up parameters.  
5
 
 
After network connection, please pick up handset, press key “#*047#” to hear IP address of the  
adaptor box. In the address field of browser, type the IP address and press ENTER to display the  
Settings page. A log-in page will be shown. Enter log-in password to set parameters. The default  
password is 1234.  
If adaptor box cannot get IP, enter “##3427# to cancel DHCP mode. After reset and beep sound  
heard, please pick up the handset, enter “#73847#xxx*xxx*xxx*xxx#” to set IP address of adaptor  
box. Get the IP address and use browser to set up.  
¾
Network Settings  
Depending on the requirement of your ISP or Network you can configure the KTA with a Static IP,  
DHCP, or PPPoE:  
Static IP: If your ISP / Network requires the use of a Static IP then you will be required to  
complete all of the parameters listed below:  
Fill in IP  
Fill in subnet mask  
Fill in default  
gateway ip  
6
 
Fill in DNS  
Fill in DNS2  
DHCP: If your router (or other network device) is configured to allocate an IP address to the KTA  
automatically then you can simply set the KTA up for DHCP operation and no other network  
parameters need to be completed.  
PPPoE: If your ADSL modem (or other network device) does not allow you to configure PPPoE then you may  
need to configure this in the KTA. You will need to enter your PPPoE Username (ID) and Password as follows:  
Fill in PPPoE id  
Fill in PPPoE psssword  
“mac” :display the KTA’s unique mac address  
Instruction:if you can’t choose corresponding net link,please consult to network administrators or ISP,and  
you may know which method is your network using,and then ,make the right settings  
¾
Protocol Settings  
Service port:  
H323:1719(default)  
Sip:5060(default)  
DNS  
or  
IP  
of  
the  
Select protocol:  
sip or h323  
servicecarrier’s soft-switch  
Phone number  
Pin  
User  
name  
with  
service provider  
7
 
Instruction: Depending on your service provider the KTA may display “gk zone” instead of  
“service address”.  
Notice: If login failed, contact your service carrier to adjust parameters. Do not ajust default value in most  
cases.  
¾
Audio Settings  
Audio codec  
Ringtype  
Voice active  
detection  
auto gain  
control  
auto echo  
cancellatio  
Notice: All above audio parameters are default settings. Contact your operator to adjust the corresponding  
parameters if any problems.Please do not adjust these without the advice of your service provider.  
¾
Other Settings  
adjust the login passport  
1234 is default value  
IP address of network  
time server  
Use Digitmap: Please leave this function turned on. The Digit map enables the KTA to recognize dialing  
sequences from around the world. If the user dials a recognized dialing sequence then the KTA initiates the call  
without the user having to press the # key after dialing.  
Notice: Enter #358# to restore factory(default value) if forget KTA login password. Pasword will restore to  
the default value, 1234.  
8
 
¾
Upgrade  
Click “Update Firmware” of the right-bottom of setting page.  
KTA would automatically reboot after uprading, then please press keys on the phone as #358##DLT#to restore  
default settings and reboot again!  
Note: If you have been instructed to use the “Upgrade Tool” to perform the upgrade then you will need to  
enable “Remote Access Permission”. This is done from your telephone handset by dialing #767#. Please  
remember that after you have completed the upgrade then you should restore the KTA’s default settings by  
dialing #358# on your phone handset and then wait for the KTA to reboot.  
¾
Other buttons  
save any changes  
you have made  
Update degitmap  
restore the settings to  
the original factory  
4. Functions  
z
z
z
Making and Receiving calls  
Use Digitmap  
Call Forwarding  
4.1 Making and Receiving calls  
4.1.1 Making outgoing calls  
A. Calling VoIP  
Every VoIP Terminal will be assigned a VoIP number. Users can directly call each other’s number.  
Example: A user with the number 6667777want to call another user with the number 7778888.  
User 6667777 simply pick up the phone handset, waits for dial tone and dial 7778888 followed by #  
B. Calling a regular phone  
a) Calling a regular phone under PSTN  
Notice: Before this function can be realized, please plug the phone line into the KTA LINE port (FXO). And  
now the phone is a VoIP phone. (Only for KTA1010, KTA1011)  
Pick up the handset or press the “handfree” key,then press the key “*” to change into the PSTN model. When you  
hear the dial tone ,key in the PSTN phone number, after finishing calls ,put down the handset, it automatically  
change to the VoIP model.  
Under this situation, functions are carried out through KTA’s LINE port (FXO).  
b) Calling regular phone under VoIP  
Notice: It is applicable to all KTA users  
9
 
 
Every KTA can call any land or mobile phone anywhere in the world. Please dial with the service carrier’s dialing  
rule. Press “#” after you dial the phone number.  
Example 1: If a U.S service carrier’s dialing rule: To call a U.S or Canada number, please first dial 1, then the  
telephone number.  
KTA user calling an U.S/Canada regular number 213-666-8888.  
Pick up the handset, when you hear the dial tone key in 12136668888 followed by #.  
Example 2: If a U.S service carrier’s dialing rule: To call other countries’ regular numbers, please first dial 011,  
then the country code (no ‘0’ as prefix), and dial the telephone at last.  
KTA user calling a China regular number 0755-88889999.  
Pick up the handset, when you hear the dial tone key in 0118675588889999 followed by #  
Example 3: If a China service carrier’s dialing rule: To call other countries’ regular numbers, please dial the  
district code, and dial the telephone at last.  
KTA user calling a China regular number 0755-88889999.  
Pick up the handset, when you hear the dial tone key in 075588889999followed by #.Under this situation,  
functions are carried out through KTA’s LAN port and PHONE port (FXS).  
4.1.2 Receiving  
A. Receiving VoIP  
When there is a call from other VoIP, pick up handset or press ”handfree” key.  
B. Receiving PSTN  
a) Notice: the function is only for KTA1010, KTA1011 and please plugs the phone line provided by telecom  
to the KTA LINE port (FXO)  
Under this situation, when calls from the PSTN phone, the phone then automatically changes to the PSTN model,  
pick up the handset and the call can be successfully going on. Functions are carried out through KTA’s LINE port  
(FXO).  
b) Notice: it is only for the users except from a)  
This is an optional service. Only areas that are provided access numbers allow calls from a regular phone to KTA.  
Please refer to ‘Access Number List’ on the Carrier Service page to see if this service is available in your area.  
4.2 Use digitmap  
After you choose” use digitmap” through the web, when you call the phone numbers all over the world, after dial  
the number, KTA can automatically dial out without pressing “#”, just as under PSTN model. The rule will be  
defined by service carrier.  
4.3 Call Forwarding  
Every KTA has call forwarding feature, when the user is not online, the incoming call can be forwarded to a preset  
telephone number.  
Settings:  
Enter my account page on service website to set the forwarded number. The number must accord with service  
carrier’s dialing rule.  
10  
 
 
Please  
input  
the  
forwarding number  
Please type in the target number, which will be forwarded to.  
Notice: Call forwarding target number must be a PSTN number, with more than 7 digits.  
Example 1: If a U.S service carrier’s dialing rule: To forward to a U.S or Canada number, please first dial 1, then  
the telephone number.  
KTA user wants to make a call forward to 213-666-8888, please fill in 12136668888.  
Example 2: If a U.S service carrier’s dialing rule: To forward to other countries’ regular numbers, please first dial  
011, then the country code (no ‘0’ as prefix), and dial the telephone at last.  
KTA user wants to make a call forward to 0755-88889999, please fill in 0118675588889999.  
Example 3: If a China service carrier’s dialing rule: To call other countries’ regular numbers, please dial the  
district code, and dial the telephone at last.  
KTA user want to make a call forward to 0755-88889999. KTA user can fill in 075588889999.  
5. Technical Parameter  
5.1 The electronic specifications  
z
Voltage: 12V DC, 500mA  
z
Power adapter: AD/DC input 100~120V (USA, Japan etc.) or 220~240V (China, Europe etc.) or 100~240V,  
47-63Hz  
z
z
Network interface: IEEE 802.3 10 Base-T  
EMC: FCC Part15 CLASS B  
5.2 Working/storing environment  
z
Operational temperature: 0 to 50° C (32° to 122° F)  
z
Storage temperature: -30° to 65° C (-22° to 149° F)  
11  
 
 
z
Humidity: 10% to 90% no dew  
5.3 Dimensions  
z
166.4x 119x 31.6mm (L x W x H)  
6. Frequent Problems and Solutions  
Problems  
Unacceptable  
quality under VoIP  
Probably Causes  
Solutions  
Using in network environment as  
stable and qualified as you can.  
voice Bandwidth < 30Kbps  
Unstable network quality:  
Delay>500ms or jitter>100ms  
or package loss>10%  
Login  
(Service LED off)  
server  
failed Login failed by firewall  
Network provided by ISP and  
the ISP restricts login  
Check with the service center of  
service carrier.  
Incorrect account information Using initial account to reset  
or phone number  
account number, pin and phone  
number. If the pin had been  
changed, asking the service carrier.  
If server address had been changed,  
asking the service carrier.  
Incorrect server address  
Failed to receive and dial Phone line provided by the Plug the phone line to the KTA  
the PSTN phone through Telecom service carrier is not LINE port (FXO)  
the phone line provided be plugged to the KTA LINE  
by the Telecom service port (FXO)  
carrier  
Incorrect dialing method  
Please dial the “*”key before call,  
then you can choose the phone line  
as the dial-out line  
Login succeeded (service Some wrong with KTA Press “#778#”(#RST#) to restore  
led on), can’t use phone: momently  
after picking up handset  
you cannot hear dial tone,  
or press key without  
sound  
KTA,then reuse  
7. Appendix  
7.1 Features  
z
z
Basic Port—— One or two RJ45 ports compatible with IEEE 802.3 10 Base-T, one FXS port, one FXO port  
(KTA1010, KTA1011)  
AC/DC adapter— input 100~120V (USA, Japan etc.) or 220~240V (China, Europe etc.) or 100~240V,  
47-63Hz  
z
z
z
z
Log-in to specific soft-switch platform  
Automatic searching for soft-switch platform  
Supports DHCP: Automatically obtain local IP, subnet mask, router IP  
Supports PPPoE  
12  
 
 
z
z
z
z
z
z
z
z
z
Voice active detection  
Comfortable noise generation  
Echo cancellation  
Dynamic buffer management—minimize effect to voice quality caused by audio delay jitter  
Supports NAT  
Supports.H.323/SIP  
Supports Remote Upgrade  
Supports Call Forwarding  
Lightningproof  
7.2 Standards and agreements  
z
z
z
z
z
z
z
z
z
z
z
z
z
z
IEEE 802.3 10 Base-T  
G.711A, G.711µ, G.723.1 5.3K/6.3 Kbps and G.729 audio codec  
H.323 v2 and SIP  
TCP/IP: Internet Transport and Control Protocol  
RTP: Real-time Transport Protocol  
RTCP: Real-time Control Protocol  
VAD/CNG Voice active detection/comfortable noise generation  
G.165 Echo cancellation  
DTMF Tone Generate and Detection  
DHCP: Dynamic Host Configuration Protocol  
PPPoE: Point to Point Protocol of Ethernet  
DNS: Domain Name Server  
FTP: File Transfer protocol  
HTTP: Hyper Text Transfer protocol  
7.3 Recommend usage net condition  
z
z
z
z
Delay:  
Less than 400ms  
Jitter:  
Less than 100ms  
Package loss: Less than 10%  
Bandwidth: More than 30Kbps  
7.4 Commands For Setting Network Parameters  
Query IP Address: #*047# or #*0IP#  
Set IP address: #73847# xxx*xxx*xxx*xxx# or #SETIP “#xxx.xxx.xxx.xxx#”  
Enable DHCP: #3427# or #DHCP#  
Disable DHCP:##3427# or ##DHCP#  
Reboot: #778# or #RST#  
Restore default settings: #358# or #DLT#  
Using H.323: #4323# or #H323#  
Using SIP: #747# or #SIP#  
Using adjusting IP #3228# or #FACT#.  
Safety Warning: Please do not place this product near open flame or high temperature. Avoid heavy  
13  
 
 
impact, and do not leave the product in dump or highly humid conditions!  
Current user manual is made based on the functions of present products, if any content change has made,  
no further notice.  
14  
 

Bissell Personal Computer 18P0 User Manual
Blackberry Cell Phone 7100I User Manual
Black Box Switch 24985 User Manual
Bogen Air Compressor CMP1R User Manual
Bosch Power Tools Cordless Drill DDS182 02 User Manual
Cabletron Systems Network Card PL500sc User Manual
Casablanca Fan Company Outdoor Ceiling Fan 69xxD User Manual
Casio Clock DQR 300U User Manual
Chief Manufacturing Indoor Furnishings CM2 User Manual
Cisco Systems Modem 4027669 User Manual