Carrier Access Network Router Terminal Server Router User Manual

Terminal Server Router  
QUICK START GUIDE  
Part Number: 002-0152-0005  
Product Release: 1.3  
May 2004  
 
QUICK START GUIDE  
n Installation  
n Basic Setup  
Routing  
Address Routing  
n Internet Connection using PPP, NAT/PAT and  
Addresses  
n Back-to-Back with PPP  
n Back-to-Back with Multi-Link PPP  
n Back-to-Back with Frame Relay  
 
Quick Start Guide  
Installation  
Installation  
Installation of the router card into the Adit chassis.  
l Unit can be on or off  
l Router card will work in any slot  
l Slide card into slot until fully seated  
l Router has completed it’s boot cycle when CRD light is solid  
The following setups are all executed with CLI  
NOTE: Configuration can be done with the following CLI commands or  
with the Router Menu-Driven Software.  
Basic Setup  
Command  
Description  
set {ds0-addr} type data  
Confirm DS0 is set to type data.  
ds0-addr = {slot:port:channel} of DS0  
Example: set a:1:1-24 type data  
connect {slot:port:trunk}  
{slot:port:channel}  
Cross-connect T1 to router card.  
Example: connect a:1:1-24 6:1:1 (router in slot 6)  
set {router-addr} proxy  
Disable/enable router proxy.  
router-addr = {slot:port}| of router card.  
Example: set 6:1 disable.  
set {slot:port} up  
Set Router LAN as In-Service.  
Example: set 6:1 up  
telnet {router_card-addr}  
Telnet to Router card.  
router_card-addr = {slot} location of router card  
Example: telnet 6 (if earlier than 3.0 release {slot:port}  
must be used)  
Local and Remote Profile Setup  
reinitialize  
To enable any configuration changes, the card must be  
reinitialized.  
4
Terminal Service Router - Release 1.3  
 
   
Quick Start Guide  
PPP Internet Connection and Public IP Address Routing  
PPP Internet Connection and  
Public IP Address Routing  
Router in Slot 1  
ISP Router that provides the Internet connection.  
Command  
Description  
set clock1 a:1  
set 1 default  
disconnect a:1  
Set primary master transmit clock source  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
set a:1:all type data  
connect a:1:all 1:1:1  
rename 1 "LocalUnit" "Boulder"  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Boulder" (LAN)  
rename 1 "RemoteUnit" "wan1"  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 1:1 ip address 215.168.21.14  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
add 1 "wan1" static ip network  
0.0.0.0 0.0.0.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 1 "wan1" trunk 1  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
reset 1  
Reboot the router, to enable all configurations set  
Terminal Service Router - Release 1.3  
5
 
 
Quick Start Guide  
Frame Relay Internet Connection and Public IP Address Routing  
Frame Relay Internet Connection and  
Public IP Address Routing  
Router in Slot 1  
ISP Router that provides the Internet connection.  
Command  
Description  
set clock1 a:1  
set 1 default  
disconnect a:1  
Set primary master transmit clock source  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
set a:1:all type data  
connect a:1:all 1:1:1  
rename 1 "LocalUnit" "Boulder"  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Boulder" (LAN)  
rename 1 "RemoteUnit" "wan1"  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 1:1 ip address 215.168.21.14  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
add 1 "wan1" static ip network  
0.0.0.0 0.0.0.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 1:1:1 encapsulation fr  
set 1 lmi annexd  
Set the encapsulation on trunk 1 to Frame Relay  
Disable LMI to Annex D  
set 1 "wan1" trunk 1  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
set 1 "wan1" dlci 101  
reset 1  
Set the DLCI number  
Reboot the router, to enable all configurations set  
6
Terminal Service Router - Release 1.3  
 
 
Quick Start Guide  
Internet Connection using PPP, NAT/PAT and Firewall Filters  
Internet Connection using PPP, NAT/PAT and  
Firewall Filters  
Router in Slot 1  
ISP Router that provides the Internet connection. Router with NAT/PAT and Firewall  
Filters.  
Command  
Description  
set clock1 a:1  
set 1 default  
disconnect a:1  
Set primary master transmit clock source  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
set a:1:all type data  
connect a:1:all 1:1:1  
rename 1 "LocalUnit" "Boulder"  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Boulder" (LAN)  
rename 1 "RemoteUnit" "wan1"  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 1:1 ip address 192.168.21.14  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
set 1 "wan1" nat enable  
Set the WAN interface named "wan1" enable  
NAT mapping  
set 1 "wan1" nat address  
216.174.44.2 1  
Set the WAN interface named "wan1" NAT  
address  
add 1 "wan1" static ip network  
0.0.0.0 0.0.0.0 1  
Adds a static IP network (route) to the WAN  
interface  
add 1 "wan1" firewall 1 pass  
incoming log telnet  
192.168.21.14/32  
Adds a Firewall rule to the WAN. Where  
xxx.xxx.xxx.xxx is the host’s IP address at the far  
end that will be able to ping or telnet to the router.  
0.0.0.0/0 will allow any other host at the far end  
to ping and/or telnet to the router.  
xxx.xxx.xxx.xxx/32  
Terminal Service Router - Release 1.3  
7
 
 
Quick Start Guide  
Internet Connection using PPP, NAT/PAT and Firewall Filters  
Command  
Description  
add 1 "wan1" firewall 2 pass  
inout nolog ping  
192.168.21.14/32  
Adds a Firewall rule to the WAN. Where  
xxx.xxx.xxx.xxx is the host’s IP address at the far  
end that will be able to ping or telnet to the router.  
0.0.0.0/0 will allow any other host at the far end  
to ping and/or telnet to the router.  
xxx.xxx.xxx.xxx/32  
add 1 "wan1" firewall 3 pass  
inout nolog ping 0.0.0.0/0  
0.0.0.0/0  
Adds a Firewall rule to the WAN.  
Adds a Firewall rule to the WAN.  
Adds a Firewall rule to the WAN.  
add 1 "wan1" firewall 4 pass  
inout nolog tcp 1-65535 0.0.0.0/0  
0.0.0.0/0  
add 1 "wan1" firewall 5 pass  
inout nolog udp 1-65535 0.0.0.0/0  
0.0.0.0/0  
set 1 "wan1" trunk 1  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
reset 1  
Reboot the router, to enable all configurations set  
8
Terminal Service Router - Release 1.3  
 
Quick Start Guide  
Internet Connection using NAT and Static NAT Addresses  
Internet Connection using NAT and Static NAT  
Addresses  
Router in Slot 1  
ISP Router that provides the Internet connection. Router with NAT and Static NAT  
addresses.  
Command  
Description  
set clock1 a:1  
set 1 default  
disconnect a:1  
Set primary master transmit clock source  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
set a:1:all type data  
connect a:1:all 1:1:1  
rename 1 "LocalUnit" "Boulder"  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Boulder" (LAN)  
rename 1 "RemoteUnit" "wan1"  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set ethernet ip address  
192.168.21.15 255.255.255.0  
Set the Ethernet IP address and Subnet Mask, for  
the Axxius 800  
set 1:1 ip address 192.168.21.14  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
set 1 "wan1" nat enable  
Set the WAN interface named "wan1" enable  
NAT mapping  
set 1 "wan1" nat address  
216.174.44.2 1  
Set the WAN interface named "wan1" NAT  
address  
add 1 "wan1" static ip network  
0.0.0.0 0.0.0.0 1  
Adds a static IP network (route) to the WAN  
interface  
add 1 "wan1" static nat address  
192.168.21.14 216.174.44.232  
Add static NAT bi-directional mapping to wan1  
Terminal Service Router - Release 1.3  
9
 
 
Quick Start Guide  
Internet Connection using NAT and Static NAT Addresses  
Command  
Description  
add 1 "wan1" static nat address  
192.168.21.15 216.174.44.233  
Add static NAT bi-directional mapping to wan1  
add 1 "wan1" static nat address  
192.168.21.16 216.174.44.234  
Add static NAT bi-directional mapping to wan1  
Add static NAT bi-directional mapping to wan1  
add 1 "wan1" static nat address  
192.168.21.17 216.174.44.235  
set 1:1:1 encapsulation fr  
set 1 lmi annexd  
Set the encapsulation on trunk 1 to Frame Relay  
Disable LMI Annex D  
set 1 "wan1" trunk 1  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
set 1 "wan1" dlci 101  
reset 1  
Set the DLCI number  
Reboot the router, to enable all configurations set  
216.174.44.232 is the static NAT address assigned to the router.  
216.174.44.233 is the static NAT address assigned to the controller.  
216.174.44.234 is the static NAT address for a server*.  
216.174.44.235 is the static NAT address for a host*.  
*In the private network that can be reached from the outside world.  
There can be up to 16 static NAT addresses, therefore the actual range can be  
216.174.44.232 to 216.174.44.247. Only 4 were used in this example.  
10  
Terminal Service Router - Release 1.3  
 
Quick Start Guide  
Back-to-Back with PPP  
Back-to-Back with PPP  
The following configuration will set up two Routers back-to-back with PPP.  
Boulder Router in Slot 1  
Command  
Description  
set 1 default  
disconnect a:1  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
set a:1:all type data  
connect a:1:all 1:1:1  
rename 1 "LocalUnit" "Boulder"  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Boulder" (LAN)  
rename 1 "RemoteUnit" "wan1"  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 1:1 ip address 1.1.1.1  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
set 1:1 phy auto  
Set the Physical Specifications to auto-negotiate  
add 1 "wan1" static ip network  
2.2.2.0 255.255.255.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 1:1:1 encapsulation ppp  
set 1 "wan1" trunk 1  
Set the encapsulation on trunk 1 to PPP  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
reset 1  
Reboot the router, to enable all configurations set  
Terminal Service Router - Release 1.3  
11  
 
 
Quick Start Guide  
Back-to-Back with PPP  
Denver Router in Slot 1  
Command  
Description  
set 1 default  
disconnect a:1  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set primary master transmit clock source  
set clock1 a:1  
set a:1:all type data  
connect a:1:all 1:1:1  
rename 1 "LocalUnit" "Denver"  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Denver" (LAN)  
rename 1 "RemoteUnit" "wan1"  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 1:1 ip address 2.2.2.1  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
set 1:1 phy auto  
Set the Physical Specifications to auto-negotiate  
add 1 "wan1" static ip network  
1.1.1.0 255.255.255.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 1 "wan1" trunk 1  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
reset 1  
Reboot the router, to enable all configurations set  
12  
Terminal Service Router - Release 1.3  
 
Quick Start Guide  
Back-to-Back with Multi-Link PPP  
Back-to-Back with Multi-Link PPP  
The following configuration will set up two Adit 600 Routers back-to-back with Multi-  
Link PPP.  
Boulder Router in Slot 1  
Command  
Description  
set 1 default  
disconnect a:1  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
Connect all of T1-1 to the Router that is in slot 1  
set a:1:all type data  
connect a:1:all 1:1:1  
connect a:2:all 1:1:2  
rename 1 "LocalUnit" "Boulder"  
Rename the Adit 600 from "LocalUnit" (default)  
to "Boulder" (LAN)  
rename 1 "LocalUnit" "Boulder"  
set 1:1:1-2 multilink group 1  
rename 1 "RemoteUnit" "wan1"  
Rename the Adit 600 from "LocalUnit" (default)  
to "Boulder" (LAN)  
Rename the Adit 600 from "LocalUnit" (default)  
to "Boulder" (LAN)  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 1:1 ip address 1.1.1.1  
255.255.255.0  
Set the Ethernet IP address, in the conventional IP  
address format. (Router LAN)  
add 1 "wan1" static ip network  
2.2.2.0 255.255.255.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 1 "wan1" trunk multilink  
group 1  
Set the WAN interface named "wan1" to be  
mapped to trunk multilink group 1  
reset 1  
Reboot the router, to enable all configurations set  
Terminal Service Router - Release 1.3  
13  
 
 
Quick Start Guide  
Back-to-Back with Multi-Link PPP  
Denver Router in Slot 1  
Command  
Description  
set 1 default  
disconnect a:1  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set primary master transmit clock source  
set clock1 a:1  
set a:1:all type data  
connect a:1:all 1:1:1  
connect a:2:all 1:1:2  
rename 1 "LocalUnit" "Denver"  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
Connect all of T1-1 to the Router that is in slot 1  
Rename the Adit 600 from "LocalUnit" (default)  
to "Denver" (LAN)  
set 1:1:1-2 multilink group 1  
rename 1 "RemoteUnit" "wan1"  
Rename the Adit 600 from "LocalUnit" (default)  
to "Boulder" (LAN)  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 1:1 ip address 2.2.2.1  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
add 1 "wan1" static ip network  
1.1.1.0 255.255.255.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 1 "wan1" trunk multilink  
group 1  
Set the WAN interface named "wan1" to be  
mapped to trunk multilink group 1  
reset 1  
Reboot the router, to enable all configurations set  
14  
Terminal Service Router - Release 1.3  
 
Quick Start Guide  
Back-to-Back with Frame Relay  
Back-to-Back with Frame Relay  
The following configuration will set up two Routers back-to-back with Frame Relay.  
Boulder Router in Slot 1  
Command  
Description  
set clock1 internal  
set 1 default  
disconnect a:1  
Set primary master transmit clock source  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 1  
Disconnect all connections to the router in slot 1  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
set a:1:all type data  
connect a:1:all 1:1:1  
rename 1 "LocalUnit" "Boulder"  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Boulder" (LAN)  
rename 1 "RemoteUnit" "wan1"  
Rename WAN #1 to "wan1"  
set 1:1 ip address 1.1.1.1  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
add 1 "wan1" static ip network  
2.2.2.0 255.255.255.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 1:1:1 encapsulation fr  
set 1 lmi disable  
Set the encapsulation on trunk 1 to Frame Relay  
Disable LMI (Local Management Interface)  
set 1 "wan1" trunk 1  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
set 1 "wan1" dlci 101  
reset 1  
Set the DLCI number  
Reboot the router, to enable all configurations set  
Terminal Service Router - Release 1.3  
15  
 
 
Quick Start Guide  
Back-to-Back with Frame Relay  
Denver Router in Slot 3  
Command  
Description  
set 3 default  
disconnect a:1  
Set Router to default settings  
Disconnect all connections to the T1 on the  
Controller (slot a)  
disconnect 3  
Disconnect all connections to the router in slot 1  
Set primary master transmit clock source  
set clock1 a:1  
set a:1:all type data  
connect a:1:all 3:1:1  
rename 3 "LocalUnit" "Denver"  
Set the T1-1 of the Controller, Type to Data  
Connect all of T1-1 to the Router that is in slot 1  
Rename the Axxius 800 from "LocalUnit"  
(default) to "Denver" (LAN)  
rename 3 "RemoteUnit" "wan1"  
Rename WAN #1 from "RemoteUnit" (default) to  
"wan1"  
set 3:1 ip address 2.2.2.1  
255.255.255.0  
Set the ethernet IP address, in the conventional IP  
address format. (Router LAN)  
add 3 "wan1" static ip network  
1.1.1.0 255.255.255.0 1  
Adds a static IP network (route) to the WAN  
interface  
set 3:1:1 encapsulation fr  
set 3 lmi disable  
Set the encapsulation on trunk 1 to Frame Relay  
Disable LMI (Local Management Interface)  
set 3 "wan1" trunk 1  
Set the WAN interface named "wan1" to be  
mapped to trunk 1  
set 3 "wan1" dlci 101  
reset 3  
Set the DLCI number  
Reboot the router, to enable all configurations set  
16  
Terminal Service Router - Release 1.3  
 

Blaupunkt Car Stereo System BPV 655 User Manual
Briggs Stratton Portable Generator 30325 User Manual
Broan Range 412404 User Manual
Brother Printer HL 1040 User Manual
Canon Digital Camera SX520 HS User Manual
CardScan Scanner 700C User Manual
Casio Digital Camera EX Z55 User Manual
C Crane Stereo System 19f User Manual
CDA Range RV 701 SS User Manual
Chicago Electric Trimmer 92115 User Manual