Carson Manufacturing Co., Inc.
5451 North Rural Street
Indianapolis, IN 46220
Phone: (888) 577-6877 Fax: (317) 254-2667
TECHNICAL BULLETIN
RADIO
PA
VOL
SIREN
HORN
MAN
WAIL
ON
YELP
POWER
PHASER
SA 430
INSTALLATION AND
OPERATING MANUAL
SA-430-73F (FLUSH MOUNT CONTROL HEAD)
SA-430-73FX (FLUSH MOUNT WITH EXTENDED MIC)
SA-430-73V (FLUSH MOUNT WITH VERTICAL LABEL)
Carson is a trademark of Carson Manufacturing Company, Inc.
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
TB0333B
Page 1 of 10
10/18/03
INSTALLATION
Proper installation of the unit is essential for years of safe, reliable operation. Please read all instruction before
installing the unit. Failure to follow these instructions can cause serious damage to the unit or vehicle and may void
warranties.
SAFETY PRECAUTIONS
For the safety of the installer, vehicle operator, passengers and the community please observe the following safety
precautions. Failure to follow all safety precautions and instructions may result in property damage, injury or
death.
Qualifications - The installer must have a firm knowledge of basic electricity, vehicle electrical systems and
emergency equipment.
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
Mounting - Mount the control head for easy access by the vehicle operator. DO NOT mount in air bag deployment
area. Assure clearances before drilling in vehicle.
Wiring - Use wiring capable of handling the current required. Make sure all connections are tight. Route wiring to
prevent wear, overheating and interference with air bag deployment. Install and check all wiring before connection to
vehicle battery.
Testing - Test all siren functions after installation to assure proper operation. Test vehicle operation to assure no
damage to vehicle.
Keep These Instructions - Keep these instructions in the vehicle or other safe place for future reference. Advise the
vehicle operator of the location.
AMPLIFIER MOUNTING
Choose a mounting location in an area such as the driver compartment firewall, under a seat, etc. Mounting the
amplifier in the engine compartment or in an area directly exposed to weather is not recommended. Assure adequate
ventilation to prevent overheating. Consider wire routing and access to connector. Install amplifier to vehicle using
1/4" hardware (not supplied).
May need to set RADIO VOLUME ADJUST on side of amplifier before final mounting and installation.
May also need to set POWER OUTPUT ADJUSTMENT on inside of amplifier.
CONTROL HEAD MOUNTING
Select a mounting location in an area such as the dash or overhead console. Choose a mounting location convenient
to the operator and away from any air bag deployment areas. Consider wire routing and access to connections, as
well as microphone bracket placement.
A microphone clip along with mounting screws (CP3633) holds the microphone in place.
FLUSH MOUNT
The flush mount control head requires a hole in the dash. Use the mounting template on the last page. Note that the
template may not print actual size and may need sizing on a copier. Use #6 screws to fasten to dash.
FLUSH MOUNT WITH EXTENDED MICROPHONE
The flush mount control head with extended microphone is mounted the same as the flush mount except that the
microphone cable extension will also go behind the dash. Allow room for this cable as well.
Control Head – Rear View
Microphone
Extension
Cable
TB0333B
Page 3 of 10
10/18/03
CONTROL HEAD ELECTRICAL CONNECTIONS
All control head leads may be extended with #22 AWG or larger lead wire.
Negative Connection (Black) - Connect to same ground or negative supply as amplifier.
Positive Connection (Red) - Connect to positive DC supply. It is recommended that the lead be connected to the
accessory output of the fuse block. This provides additional protection of a fused input to the control head.
Lights (Yellow) - This lead may be connected to the dash lights or to the red power lead. Connecting to the dash
lights will turn on the panel lights whenever the dash lights are on.
When connected to the red lead, make sure that the ignition switch controls the power to that connection. This
prevents the panel lights from being continuously on.
Control (White) - Connect to white lead from amplifier. Route this lead away from radio transmitter antenna lead to
prevent RF interference being fed to the siren amplifier.
Auxiliary Input (Green) - Used for Siren control. Performs same function as Siren button. Connect to a normally
open switch or to horn ring circuit. Circuit may connect to either positive or negative. When connected to horn ring
circuit, use a SPDT switch to connect horn ring to either vehicle horn or to manual control circuit.
NOTE: Permanent disconnection of the vehicle horn is NOT recommended.
NOTE: Be sure to cut lead short if not used to prevent R.F. interference and insulate with electrical tape.
Added
SPDT
Switch
HORN
RING
SWITCH
HORN
AUX
HORN RING
CONNECTION
TB0333B
Page 4 of 10
10/18/03
AMPLIFIER ELECTRICAL CONNECTIONS
Disconnect vehicle battery before making the following electrical connections.
Electrical connections to the amplifier are made using the wiring harness supplied. If the amplifier needs service the
connector can be easily removed without unwiring the harness. The power supply for the amplifier must be capable of
delivering peak currents up to 50 amps for adequate short circuit protection and reliable operation. The preferred
source is directly at the vehicle battery. A fuse on the unit protects from overload.
Wire Size and Termination - The diagram shows the minimum wire size used for each connection. If the wire is
longer than 10 ft. use the next larger wire size. Use only high quality crimp connectors for installation on the vehicle.
Negative Connection (Black) - Both leads must be used. Connect to negative battery connector or high current
buss.
Positive Connection (Red) - Both leads must be used. Connect to positive battery connector or high current buss. A
power relay may be used.
Speaker Connection (Brown) - Both leads must be used. Connect 1 lead to each terminal or lead of the speaker.
When used with 2 speakers connect each brown lead to both speaker terminals or leads (parallel circuit). Observe
polarity (phasing) when connecting 2 speakers.
Control Connection (White) - Connect to white lead from control head. Route this lead away from radio transmitter
antenna lead to prevent RF interference being fed to the siren amplifier.
Optional Radio Input Connection (Blue) - Connect 1 lead to each terminal of the radio speaker or output connector.
The input is isolated and polarity is not important. May need to set RADIO VOLUME ADJUST on side of unit.
#14 AWG RED
CONTROL HEAD
Use both leads
Extend with #12
+
GRN (AUX)
BAT
RADIO
HORN
SIREN
-
VOL
YEL (DASH LIGHTS)
BLK (-VDC)
#14 AWG BLK
Use both leads
Extend with #12
MAN
WAIL
ON
YELP
POWER
PHASER
RED (+VDC)
(2) #18 AWG BRN
(#16 - 2 SPKR)
2 - SPKR - Connect for
same phase (+ to +)
WHT
CONTROL
RADIO
CP2560
CABLE
AMPLIFIER
(2) #18 AWG BLU
Connect to output
jack, terminals or
speaker of radio
20AMP FUSE
AUTOMOTIVE TYPE
BLK TO -VDC
CONTROL
#18 AWG WHT
BLU TO TWO WAY
RADIO SPEAKER
AMPLIFIER WIRING
HARNESS CONNECTIONS
BRN TO SPKR
RED TO +VDC
TB0333B
Page 5 of 10
10/18/03
OPERATION
Sound Hazard - Sound level from siren speaker (>120dBA @ 10 feet) may cause hearing damage.
Do not operate siren without adequate hearing protection for you and anyone in immediate vicinity.
(Ref. OSHA 1910.95 for occupational noise exposure guidelines)
RADIO
PA
VOL
SIREN
HORN
MAN
WAIL
ON
YELP
POWER
PHASER
SA 430
The Toggle Power Switch controls the siren power. The siren may be left on any time the vehicle is in operation. The
power should be turned off when vehicle is not being used to conserve battery power.
The Rotary Function Switch selects various operating modes. These modes are as follows:
RADIO -
This mode reproduces, or repeats, the output of a radio. The radio must be connected and
RADIO VOLUME ADJUSTed for this mode to function. PA override available in this mode.
HORN -
MAN -
Also considered a standby mode. Horn and PA Override available in this mode.
The siren tone is controlled Manually with SIREN button. PA Override available in this mode.
WAIL -
The siren produces a normal rise-fall tone pattern. This mode should be used on highways or
areas with constant traffic flow. Yelp and PA Override available in this mode.
YELP -
The siren produces a moderate warble tone. This mode should be used in lightly congested
areas. Horn and PA Override available in this mode.
PHASER -
The siren produces a very fast warble tone. This mode should be used at intersections or in
highly congested areas. Horn and PA Override available in this mode.
OVERRIDE FUNCTIONS
PUBLIC ADDRESS
(PA) OVERRIDE -
Pressing the microphone button in any operating mode allows the operator to use the siren as
a public address amplifier. The operating mode resumes when the button is released. (Hold
the microphone close to your lips for proper operation and adjust the PA VOLume Control)
HORN OVERRIDE -
By pressing the SIREN button the siren tone output is replaced by the horn tone. The siren
tone resumes when the button is released. (This feature is not available in WAIL mode.)
YELP OVERRIDE -
Available only in WAIL mode. By momentarily pressing the SIREN button the tone output is
switched to the Yelp tone. Pressing the button again switches the tone output back to Wail.
TB0333B
Page 6 of 10
10/18/03
RADIO VOLUME ADJUST
The RADIO VOLUME ADJUST is a one time setting which depends on the radio connected and its normal volume.
Access the RADIO VOLUME ADJUST through a hole on the side of the amplifier.
Switch siren to RADIO mode and turn on the power. With the volume on the radio itself set to normal level, set the
RADIO VOLUME ADJUST to the desired level.
POWER OUTPUT ADJUST
The POWER OUTPUT ADJUSTMENT is a one time setting which depends on the speaker(s) used.
The amplifier cover must be removed to access the adjustment.
Remove the 4 screws on the side of the amplifier.
For 58W or 80W speaker(s), set the POWER OUTPUT SWITCH to “58/80”.
For 100W speaker(s) set the POWER OUTPUT SWITCH to “100”.
POWER OUTPUT SWITCH
(INSIDE AMPLIFIER ON CHASSIS)
RADIO VOLUME ADJUST
58/80
100
TB0333B
Page 7 of 10
10/18/03
SERVICE
This unit is designed to provide years of reliable service under even the worst conditions. Many times there may
appear to be a problem with the unit when the true problem is in the speaker(s) or improper installation. The following
chart shows typical symptoms and possible causes.
A blown fuse doesn't necessarily mean that the unit is bad. If a speaker or speaker lead is shorted this fuse will blow
before the unit is damaged. Disconnect the SPKR leads and replace the fuse. If the siren emits a sound when in the
Yelp position it is OK. Check the speaker(s) or leads for possible shorting.
PROBLEMS
Symptom
Possible Cause
Check
No Power or siren output Power switch not turned on
Bad Speaker
Does backlighting come on?
Do you hear a “pop” when turned on?
With siren on, yelp selected, listen for tone in
amplifier.
Connector or connections loose
Fuse blown
Loose connection at power source Is an external fuse or circuit breaker used?
Are the power leads connected to a good buss?
No siren tone –
PA works
High Voltage Protection
Mic Button stuck
The input voltage must be less than highest rating.
Does Mic Button release properly?
No PA
Distorted siren sound
PA volume not set properly
Speaker assembly loose
Intermittent Aux Input connection
Low Vehicle voltage
High Voltage Protection
Connector loose
Try turning the PA volume control.
Is the speaker bell or tip loose?
Is the Aux Input used and wired properly?
The input voltage must be greater than lowest rating.
Is the vehicle voltage regulator working properly?
Is the connector tight on the back of the unit?
Intermittent siren tone
Loose connection at power source Check for loose leads back to power source.
Mic Button activation
Circuit breaker in supply
connection
Is something lying on the microphone?
Is a circuit breaker used with at least 50A rating?
Horn or manual stuck on Siren switch stuck
Aux Input improperly connected
Does the Siren pushbutton switch return fully when
released?
Is the Aux Input used and wired properly?
Is the radio connected properly to the unit?
Can you hear the radio in the vehicle?
Try adjusting the internal radio volume control.
Are control head and amplifier connected to good
ground?
No Radio
Unit not connected to a radio
Radio volume too low
Wrong siren tone
Ground system noise
RETURN
If you have any questions concerning this or any other Carson product, please contact our Technical Service
Department at (888) 577-6877. Many issues can be handled over the phone. We can also be reached via e-mail at
If a product must be returned for any reason, please contact our Technical Service Department to obtain a Returned
Merchandise Authorization number (RMA#) before you ship the product to Carson. Please write the RMA# clearly on
the package near the mailing label. Be sure to provide a return address, contact and phone number, along with a brief
description of the problem.
TB0333B
Page 8 of 10
10/18/03
PARTS
1
7
2
4
5
6
RADIO
HORN
MAN
PA
VOL
SIREN
8
WAIL
3
ON
9
YELP
POWER
PHASER
SA 430
13
11
12
10
Control Head
Item Part #
Description
1
8025 DRS/CAP
Button, red w/ dress nut (C&K #801803000 Cap, #702501201 Nut) (for pushbutton switch)
CP3040
ES00003-09
CP3046
CP4000
CP3045
CP3880
CP4852
CP4853
CP3149
CP3853
Cable, control head power
Cable, microphone extension 8FT (CP3850 is 18FT) (for SA-430-73FX version)
Control, PA volume (1K ohm) (for all other PCB's)
Control, PA volume no face mount (1K ohm) (for PCB CP3873 Rev. E and higher)
Cover, control head back (for PCB CP2602)
Cover, control head back push on (for PCB CP3873)
Knob, rotary function switch
Knob, PA volume control
Label, control head front panel (for SA-430-73F and FX version)
Label, control head front panel vertical (for SA-430-73V version)
2
3
4
5
JKL#7001PSBL Lamp, T-1-3/4 14V Bi-pin (JKL #7001)
CP3570
ES00028-10
CP3633
Microphone (for SA-430-73F and V version)
Microphone with locking connector (for SA-430-73FX version)
Microphone clip with mounting screws
6
CP3035-1
SR3055
8121D2V40
7101-T-C-Q
CP3599
Panel, control head front
Rivet, plastic snap for back cover (Richco #SR-3055B)
Switch, pushbutton siren (C&K #8121SD2V4GE)
Switch, toggle power (C&K #7101TCQ)
Switch, rotary function
7
8
9
Amplifier
Item Part #
Description
10
CP3866
CP2560
CP3606
CP3408
SR3055
CP4119
Cable, amplifier internal chassis plug wiring harness
Cable, amplifier external wiring harness
Cover, amplifier (does not include CP3605 chassis)
Fuse holder
Rivet, plastic snap for PCB mount (Richco #SR-3055B)
Transistor, output (2 required) (Industry standard TIP36C, Not Texas Instruments)
11
12
13
TB0333B
Page 9 of 10
10/18/03
CONTROL HEAD INSTALLATION TEMPLATE
TB0333B
Page 10 of 10
10/18/03
|