SLP-2002 USERS MANUAL
SLP-2002 Stereo Balanced Vacuum Tube
Preamplifier
Fully Balanced Vacuum Tube Line Stage Circuit Design
with Cinema Bypass and Remote Volume Control
CARY AUDIO DESIGN
1020 GOODWORTH DRIVE
APEX, NORTH CAROLINA 27539
SLP-2002 USERS MANUAL
Special listening note: The SLP-2002 will need approximately 100 hours of ‘burn-in’ time
to sound its best. A new vacuum tube takes this amount of time to fully settle into its long term
operating condition. During the first 100 hours the SLP-2002 will sound good but it will improve
in its sonic characteristics as the burn-in period progresses. So, it will initially sound good and it
will get better as the first 100 hours of use passes! Enjoy the listening!
INITIAL SET UP OF THE SLP-2002 IN YOUR SYSTEM
The rear panel: When looking at the rear panel of the SLP-2002 you will see the well-
spaced, high quality connectors for inputs and outputs. From the left to the right side of the rear
panel you will have XLR or RCA input connectors for your CD player. Next on the panel is the
XLR or RCA input set for AUX 1. The Inputs for AUX 2, AUX 3 and AUX 4 use RCA
connectors exclusively, as does the Tape Monitor loop. The Cinema bypass uses XLR or RCA
input connections. The main preamplifier outputs are XLR and RCA sets, with two sets of RCA
outputs. The main power fuse holder and an IEC standard AC power cable connector are the
remaining features of the rear panel.
We chose to offer XLR and RCA inputs for the main source components so that music lovers
have more choice in matching the SLP-2002 with other high performance audio components.
The SLP-2002 is a true balanced design with four line stages, from input to output and offers
superb sound in a balanced system. We suggest using a Cary Audio Design CD player for a
balanced input source, of course! Our CD-303/200 or CD-306/200 CD players would match up
with this preamplifier very well. Both CD players have balanced output connections and would
make the most of your sound system.
The dual RCA outputs are convenient for you if you want to use a powered sub woofer with
your main speakers. Connect one set of RCA output connections to your power amplifier and
the other set to the self powered sub woofer’s input connections. Adjusting the variable volume
control on your sub woofer can attain level matching between the main speakers and the sub
woofer. Or you can use a second power amplifier and run music somewhere else in the house
from the second set of main RCA outputs. Bi-Amp operation with two power amplifiers driving
a single pair of speakers through direct speaker cable connections to the separate woofer and
tweeter terminals on the speakers is also possible with dual RCA preamplifier outputs.
We suggest that you choose excellent quality patch cables, with good ground shielding, for your
system. Wire quality does matter and careful selection of wire for your system is something we
recommend to maximize your listening enjoyment. Ask your Cary Audio Design dealer for
advice about system wiring for your stereo sound system.
The front panel: From left to right: AC Power switch, Mute/Operate switch, Cinema Bypass
switch, Volume (Listening Level) control, Input Selector, Tape Monitor and Headphone Off/On
switch. Each switch has an LED next to it to confirm operation or its selection as a function; the
only exception being the Input Selector. The Volume control shows operation by flashing an
LED while it is rotating. This visually confirms proper operation, as does the obvious change in
volume level through the speakers or headphones.
SLP-2002 USERS MANUAL
SLP-2002 Design Features: The headphone jack is driven by the buffer stage 5814 tubes
through specially chosen audio grade transformers. These audio grade transformers were
included so that the sound quality of the SLP-2002 would be preserved and offered to
headphone lovers. Headphones may be used with or without having the power amplifier and
speakers turned on. If you have very efficient speakers and inefficient headphones, it may be
necessary to turn off the power amp to avoid excessive ‘in room’ loudness. The 6922 driver
tubes are direct coupled to the 5814 buffer stage tubes for the best sound and drive capability in
this preamplifier. With the 5814 tubes driving the headphone transformers, the result is a
glorious sounding headphone driver circuit.
The SLP-2002 power supply has five fully regulated stages for the B+, the tube filaments and the
control systems related to the volume control. The volume control is a four-gang ALPS
potentiometer. This four-gang design is needed due to the truly balanced design of the four line
stages in the preamplifier.
The Remote Control Handset: Please insert the AAA batteries into the handset, aligning
the positive and negative terminals to ensure the remote control functions properly. The
handset flashes a small red LED to confirm it is working. If you push a button and the red LED is
not flashing it indicates that the batteries are depleted. Change to new batteries and your
remote control will work again. The remote control handset has Volume control Up or
Down and muting On or Off.
If you engage the mute circuit the SLP-2002 output circuit is muted. However, the
remote handset will still operate the volume control circuit. Please be
careful not to turn up the volume to a high level and then turn the mute off on the SLP-
2002. The subsequent high volume level signal might startle you or possibly damage your
speakers if it is set at too loud a level.
SLP-2002 USERS MANUAL
Specifications for the SLP-2002
Regular Inputs: Five source components, 2 XLR or RCA, 3 RCA only connection
Extra Input: Cinema bypass XLR or RCA connection
Circuit design: Fully balanced, 4 separate line gain stages, Class A triode operation
Frequency Response:
9 Hz – 70 kHz +/- 3 dB
<0.1 % @ 2 volts output
<0.1 % @ 2 volts output
< 80 dB below full output
2 volts
Total Harmonic distortion:
Intermodulation distortion:
Signal to Noise Ratio (A-weighted):
Rated output voltage:
Maximum output voltage:
Overall gain:
15 volts
20 dB
Tube complement:
(2) 6922 Gain stage
(2) 5814 Low impedance buffer
Dimensions, H x W x D Inches/Millimeters:
Weight, Pounds/Kilograms:
Power Consumption:
~5” x 17.5” x 15”/~127 x 381 x 324
~25-lb/~11.4 kg
75 watts
Voltage:
110-120/220-240 VAC, 50/60 Hz
SLP-2002 USERS MANUAL
SAFETY WARNING: Vacuum tube circuits need high voltage to work properly.
Please do not open the cabinet of the SLP-2002 while the preamplifier
is on or plugged into an AC power supply. Even when it is unplugged there is
high voltage present in the circuitry, stored by the capacitors on the main circuit board.
Please do not install the SLP-2002 where moisture or condensation will fall on it. We
recommend any service to be performed by your Cary Audio dealer. If any liquid enters
into the preamplifier unplug it immediately and do not plug it in again until any and all
liquid has been removed and the interior of the preamplifier is dry.
Cary Audio Design
1020 Goodworth Drive
Apex, North Carolina 27539
Tel: 919-355-0010
Fax: 919-355-0013
E-mail: [email protected]
SYSTEM TROUBLESHOOTING HINTS
NO POWER
NO SOUND
IS THE AC CORD CONNECTED TO A SWITCHED AC OUTLET?
IS THE SWITCHED AC OUTLET TURNED ON?
CHECK THE POWER FUSE FOR THE AC OUTLET.
CORRECT INPUT SELECTED? IS THE AMPLIFIER
TURNED ON? IS THE SOURCE COMPONENT TURNED ON?
IS THE SOURCE COMPONENT CONNECTED PROPERLY?
ARE THE SPEAKER WIRES CONNECTED PROPERLY?
NO BASS
IS THE SUBWOOFER AMPLIFIER TURNED ON?
IS THE POWERED SUBWOOFER TURNED ON?
ARE THE “WOOFERS” IN YOUR SPEAKERS DAMAGED?
ARE THE SPEAKERS WIRED CORRECTLY?
POOR TRACKING
IS THE DISC DIRTY OR SCRATCHED? IS THE DISC
(CD, DVD PLAYER) SEVERELY WARPED? IS THE DISC SEMI-TRANSPARENT OR
POORLY MADE WITH VISIBLE “PIN” HOLES?
POOR, DULL SOUND ARE THE HEADS DIRTY? HEADS MAGNETIZED FROM LONG
WOW & FLUTTER USAGE WITHOUT DEMAGNETIZING? ARE THE PINCH
(TAPE DECK)
ROLLER AND THE CAPSTAN DIRTY? CLEAN WITH PURE
ALCOHOL, “Q” TIP COTTON BUDS OR A TAPE DECK
CLEANING KIT. DEMAGNETIZE THE HEADS WITH A HAND
HELD DEMAGNETIZER. DO NOT USE ABRASIVE DRY CLEANERS!
SLP-2002 USERS MANUAL
DISTORTED BASS OVERLOADING SMALL SPEAKERS?
TOO LOUD VOLUME “CLIPPING” YOUR AMPLIFIER?
DAMAGED WOOFERS IN YOUR SUB OR MAIN SPEAKERS?
“HUM” IN SYSTEM AC CORD, VIDEO, DIGITAL AND AUDIO CABLES TOUCHING?
THE AC CORD SHOULD BE SEPARATE FROM SIGNAL CABLES
SIGNAL CABLES LAYING NEAR A LARGE POWER
TRANSFORMER, SUCH AS IN A POWER AMPLIFIER?
DEFECTIVE OR UNSHIELDED SIGNAL CABLES?
GROUND LOOP? USE A 3 to 2 CHEATER PLUG TO ‘LIFT’ THE GROUND.
OVERHEATING
IS A COMPONENT STACKED ON THE AMPLIFIER?
IS THE AMPLIFIER ENCLOSED IN A SMALL SPACE? A
MINIMUM OF 3 TO 4” (~8-10 CM) CLEARANCE IS NEEDED
ABOVE THE AMPLIFIER IN A SYSTEM. DO NOT STACK
COMPONENTS ON THE AMPLIFIER. AN AMPLIFIER NEEDS TO
“BREATHE” FREELY TO STAY COOL.
POOR RECEPTION IS THE ANTENNA CONNECTED PROPERLY? IS THE
(FM RADIO)
ANTENNA MOUNTED AS HIGH AS POSSIBLE? IS THE
ANTENNA ORIENTED FOR BEST RECEPTION? IS THE FM
STATION DISTANT? AN OUTDOOR ANTENNA MAY BE
NECESSARY. ADJUST THE ANTENNA FOR BEST RECEPTION.
NOISY RECEPTION IS THE ANTENNA CONNECTED PROPERLY? IS THERE A
(AM RADIO)
LARGE ELECTRICAL MOTOR, COMPUTER OR COMPRESSOR
NEAR THE TUNER OR ANTENNA? NOISE IS EASILY RECEIVED
IN THE AM BAND. ADJUST THE AM ANTENNA FOR BEST
RECEPTION AND MINIMUM INTERFERENCE.
Below are photos of the Cary Audio Design V-12 stereo (left) and mono (right) power amplifiers. Both amplifiers are
an excellent match to the SLP-2002 preamplifier.
The V-12 stereo amplifier is rated 50 watts/channel in triode mode. The V-12 Mono is rated at 100 watts in triode
mode. Both power amplifiers double their output power in the ultralinear mode. Each offers output from 4 or 8-ohm
speaker terminals. Both have balanced or RCA inputs and use audiophile quality connections on the rear panel for
input selection, XLR or RCA connections and for the speaker output terminals.
|