MO0404-EC
Operation Guide 2532
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to carefully read this manual and keep it on hand for later reference
when necessary.
Warning!
• The longitude, lunitidal interval, Moon phase indicator, and tide graph data that
appear on the display of this watch are not intended for navigation purposes.
Always use proper instruments and resources to obtain data for navigation
purposes.
Expose the watch to bright light to charge its battery before using it.
You can use this watch even as its battery is being charged by exposure to bright
light.
• Be sure to read“Battery”of this manual for important information you need to
know when exposing the watch to bright light.
• This watch is not an instrument for calculating low tide and high tide times. The
tide graph of this watch is intended to provide a reasonable approximation of tidal
movements only.
• CASIO COMPUTER CO., LTD. assumes no responsibility for any loss, or any
claims by third parties that may arise through the use of this watch.
If the display of the watch is blank...
If the SLEEP indicator is on the display, it means that the
display is blank because the watch’s Power Saving
function has turned off the display to conserve power.
Power Saving automatically turns off the display and puts
the watch into a sleep state whenever your watch is left for
a certain period where it is dark.
About This Manual
• Button operations are indicated using the letters shown
in the illustration.
• Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
• The initial factory default setting is Power Saving on.
• The watch recovers from the sleep state if you move it to
a well-lit area , if you press any button, or if you angle
*
the watch towards your face for reading.
It can take up to five seconds for the display to turn on.
• See “Power Saving Function” for more information.
*
(Light)
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Moon / Tide Data Mode
Coutdown Timer Mode
Timekeeping Mode
Press C.
L
Dual Time Mode
Stopwatch Mode
Alarm Mode
Timekeeping
• Note that you must add one hour to the GMT differential for your time zone
whenever you change to Daylight Saving Time. Subtract one hour when you change
back to Standard Time.
• The lunitidal interval is the time elapsing between the Moon’s transit over a meridian
and the next high tide at that meridian. See “Lunitidal Interval” for more information.
• This watch displays lunitidal intervals in terms of hours and minutes.
• The “Site Data List” and “Lunitidal Interval List” provide GMT differential, longitude,
and lunitidal interval information around the world.
Use the Timekeeping Mode to set and view the current
Moon phase indicator
time and date.
Tide graph
• The tide graph shows tidal movements for the current
date in accordance with the current time as kept in the
Timekeeping Mode.
PM indicator
• The Moon phase indicator shows the current Moon
phase in accordance with the current date as kept in the
Timekeeping Mode.
• The following is the initial factory default Home Site data (Tokyo, Japan) when you
first purchase the watch, whenever battery power drops to Level 5, and whenever
you have the battery replaced. Change these settings to match the area where you
anormally use the watch.
GMT differential (+9.0); Longitude (East 140 degrees); Lunitidal interval (5 hours,
20 minutes)
Important!
• Moon phase, tide graph data, and Moon/Tide Data
Mode data will not be displayed properly unless the
Timekeeping Mode current date and time settings and
Home Site data are configured correctly. See “Home
Site Data” for more information.
Day of week
Month – Day
Hour : Minutes Seconds
To configure Home Site data
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press A again to display the GMT differential setting
screen.
3. Press C to move the flashing in the sequence shown
below to select other settings.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C to move the flashing in the sequence shown
below to select other settings.
GMT differential
Year
GMT
differential
Lunitidal Interval
Hours
Lunitidal Interval
Minutes
Longitude
12/24-Hour
Format
Seconds
Power Saving
Minutes
Month
Hour
Day
Year
4. When the setting you want to change is flashing, use D and B to change it as
described below.
3. When the setting you want to change is flashing, use D and B to change it as
Setting
Screen
Button Operations
described below.
GMT differential
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of –11.0
to +14.0, in 0.5-hour unit.
To change this setting
Perform this button operation
Press D to reset to 00.
Seconds
Longitude
Use D (+) and B (–) to change the setting.
• You can specify a value in the range of
179°W to 180°E, in 1-degree units.
Hour, Minutes, Year,
Month, Day
Use D (+) and B (–) to change the setting.
12/24-Hour Format
Press D to toggle between 12-hour (12H) and
24-hour (24H) timekeeping.
Lunitidal Interval
Hours, Minutes
Use D (+) and B (–) to change the setting.
Power Saving
Press D to toggle Power Saving on (ON) and off
(OFF).
5. Press A to exit the setting screen.
4. Press A twice to exit the setting screen.
• The first press of A displays the GMT differential setting screen. Pressing A again
exits the setting screen.
Moon/Tide Data
Moon/tide data lets you view the Moon age and Moon
phase for a particular date, and tidal movements for a
particular date and time for the Home Site.
• See “Power Saving Function” for details about configuring Power Saving settings.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all modes.
Moon phase indicator
Tide gragh
• If you suspect that the Moon/tide data is not correct for
some reason, check the Timekeeping Mode data
(current time, date, and Home Site settings), and make
changes as required.
• See “Moon Phase Indicator” for information about the
Moon phase indicator and “Tide Graph” for information
about the tide graph.
• The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
Home Site Data
Moon phase, tide graph data, and Moon/Tide Data Mode data will not be displayed
properly unless Home Site data (GMT differential, longitude, and lunitidal interval) is
configured correctly.
• The GMT differential is the time difference of the time zone where the site is located
from Greenwich Mean Time.
• All of the operations in this section are performed in the
Moon/Tide Data Mode, which you enter by pressing C.
Moon age
1
Operation Guide 2532
To set an alarm time
To measure times with the stopwatch
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
Elapsed Time
B
➤
D
➤
D
➤
D
D
➤
Start
Stop
Re-start
Stop
Clear
x1
x2
x3
x4
Split Time
B
➤
➤
D
➤
B
D
Start
➤
B
Split
(SPL displayed)
➤
ON or OFF
:00
x5
Split release
Stop
Clear
• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2
through 5 can be used as one-time alarms only.
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash. This indicates the setting screen.
Two Finishes
D
➤
B
➤
B
D
Start
➤
B
Split
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Clear
First runner
3. Press C to move the flashing between the hour and minute settings.
4. While a setting is flashing, use D (+) and B (–) to change it.
• When setting the alarm time using the 12-hour format, take care to set the time
correctly as a.m. (no indicator) or p.m. (P indicator).
finishes.
Display time of
first runner.
5. Press A to exit the setting screen.
Dual Time
Alarm Operation
The Dual Time Mode lets you keep track of time in a
different time zone.
• The seconds count of the Dual Time is synchronized
with the seconds count of the Timekeeping Mode.
Dual time
(Hour : Minutes Seconds)
The alarm sounds at the preset time for about 10 seconds. In the case of the snooze
alarm, the alarm operation is performed a total of seven times, every five minutes, until
you turn the alarm off or change it to a one-time alarm.
The watch also has a brightness alarm. When turned on, the brightness alarm causes
the watch to beep for 10 seconds when the watch is brought from the dark into the
light. The following are the conditions for brightness alarm operation.
• The watch needs to be in the dark for about 30 to 35 minutes for the brightness
alarm to become activated.
To set the Dual Time
1. Press C to enter the Dual Time Mode.
2. Use A, B, and D to set the Dual Time Mode time.
• Each press of D (+) and B (–) changes the time
setting in 30-minute increments.
• The brightness alarm sounds about 15 to 20 minutes after the watch is next exposed
to light.
Timekeeping Mode time
• Pressing A sets the Dual Time Mode to the same time
• The brightness alarm sounds only once and then turns off automatically.
as the Timekeeping Mode.
Note
• Pressing any button stops the alarm tone operation.
• Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the Alarm 1 setting screen
Backlight
The backlight uses an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch automatically turns on
the backlight when you angle the watch towards your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Backlight Precautions” for other important
information about using the backlight.
Auto light switch
on indicator
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn Alarms 2 through 5 on and off
1. In the Alarm Mode, use D to select a one-time alarm
One-time alarm on
indicator
(alarm number 2 through 5).
To turn on the backlight manually
In any mode, press L to illuminate the display for about
one second.
• The above operation turns on the backlight regardless of
the current auto light switch setting.
2. Press B to toggle the displayed alarm on and off.
• Turning on a one-time alarm (2 through 5) displays the
one-time alarm on indicator (ALM) on its screen.
• The one-time alarm on indicator is displayed in all
modes.
About the Auto Light Switch
• If any alarm is on, the alarm on indicator is shown on
the display in all modes.
Turning on the auto light switch causes the backlight to turn on for about one second,
whenever you position your wrist as described below in any mode. Note that this
watch features a “Full Auto EL Light,” so the auto light switch operates only when
available light is below a certain level. It does not turn on the backlight under bright
light.
To select the operation of Alarm 1
1. In the Alarm Mode, use D to select Alarm 1.
2. Press B to cycle through the available settings in the sequence shown below.
SNZ indicator and one-time alarm on indicator
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes the backlight to turn on.
ALM
SNZ ALM
One-time alarm on
Snooze alarm on
Alarm off
Parallel to
ground
More than
40°
• The applicable alarm on indicator (ALM or SNZ ALM) is displayed in all modes
when an alarm is turned on.
• The SNZ indicator flashes during the 5-minute intervals between alarms.
• Displaying the Alarm 1 setting screen while the snooze alarm is turned on
automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).
To turn the hourly time signal and the brightness alarm on and off
Warning!
1. In the Alarm Mode, use D to select the Hourly Time
• Always make sure you are in a safe place whenever you are reading the
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
surprise or distract others around you.
Hourly time signal on
indicator
Signal or the brightness alarm.
2. Press B to toggle the displayed item on and off.
• Turning on the Hourly Time Signal displays the hourly
time signal on indicator (SIG) on its screen.
• Turning on the brightness alarm displays the brightness
alarm on indicator (BRT) on its screen.
• The hourly time signal on indicator and brightness alarm
on indicator are displayed in all modes.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
Brightness alarm on
indicator
To turn the auto light switch on and off
In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light
switch on (AUTO EL displayed) and off (AUTO EL not displayed).
• The auto light switch on indicator (AUTO EL) is on the display in all modes while the
auto light switch is turned on.
Battery
This watch is equipped with a solar cell and a rechargeable battery (secondary
battery) that is charged by the electrical power produced by the solar cell. The
illustration shown below shows how you should position the watch for charging.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
Minutes
• The display range of the stopwatch is 99 hours, 59
minutes, 59.99 seconds.
Hours
Seconds
Example: Orient the watch so its
Solar cell
face is pointing at a light source.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• Note that charging efficiency
drops when any part of the solar
cell is blocked by clothing, etc.
• The illustration shows how to
position a watch with a resin band.
Important!
1/100 second
• Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Be sure that the watch is normally exposed to bright light
whenever possible.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
3
Operation Guide 2532
• This watch employs a solar cell that converts light into electricity, which charges a
Reference
built-in rechargeable battery. Normally, the rechargeable battery should not need
replacement, but after very long use over a number of years, the rechargeable
battery may lose its ability to achieve a full charge. Should you notice problems with
getting the rechargeable battery to a full charge, contact your dealer or CASIO
distributor about having the rechargeable battery replaced.
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
• The rechargeable battery should be replaced with a CASIO-specified CTL1616
battery only. Other rechargeable batteries can cause damage to the watch.
• All data stored in memory is deleted, and the current time and all other settings
return to their initial factory defaults whenever battery power drops to Level 5 and
when you have the battery replaced.
• Turn on the watch’s Power Saving function and keep it in an area normally exposed
to bright light when storing it for long periods. This helps to keep the rechargeable
battery from going dead.
Power Saving Function
When turned on, the Power Saving function automatically
puts the watch into a sleep state whenever it is left in an
area where it is dark for 30 to 35 minutes. The sleep state
is indicated by a blank screen with SLEEP flashing on it.
In the sleep state, all functions are enabled, except for the
display.
• Wearing watch inside the sleeve of clothing can cause it
to enter the sleep state.
Battery Power Indicator
The battery power indicator on the display shows you the current status of the
rechargeable battery’s power.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area. It can take up to five seconds for the display to turn
Level Battery Power
Indicator
Function Status
Battery power indicator
on.
• Press any button.
• Angle the watch towards your face for reading.
1
2
3
4
All functions enabled.
All functions enabled.
All functions enabled.
To turn Power Saving on and off
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press C seven times until the Power Saving on/off
screen appears.
Beeper tone, backlight,
display, and buttons are
(Charge Soon Alert) disabled.
3. Press D to toggle Power Saving on (ON) and off
(OFF).
4. Press A twice to exit the setting screen.
• The Power Saving on indicator (SAVE) is on the display
in all modes while the Power Saving is turned on.
5
All functions, including
timekeeping, are disabled.
• The flashing
indicator at Level 4 tells you that battery power is very low, and that
exposure to bright light for charging is required as soon as possible.
• At Level 5, all functions are disabled and settings return to their initial factory
defaults. Functions are enabled once again after the rechargeable battery is
charged, but you need to set the current time, date, and all other settings after the
battery is recharged to Level 3 from Level 5. Though the time appears on the display
after the battery is charged to Level 4, you will not be able to change the time setting
until the battery reaches Level 3.
• Leaving the watch in direct sunlight or some other very strong light source can
cause the battery power indicator to temporarily show a reading that is higher than
the actual battery level. The correct battery power indicator should appear after a
few minutes.
• If you use the backlight or any of the alarm functions a number of times during a
short period, RECOVER appears on the display and the following operations
become disabled until battery power recovers.
Backlight
Beeper tone
Moon Phase Indicator
The Moon phase indicator of this watch indicates the current phase of the Moon as
shown below.
Moon phase (part you can see)
(part you cannot see)
Moon Phase
Indicator
Moon Age
0, 1, 29 2 - 5
6 - 9 10 - 13 14 - 16 17 - 20 21 - 24 25 - 28
Moon Phase
First
Quarter
(Waxing)
Full
Moon
Last
Quarter
(Waning)
New
Moon
• The Moon phase indicator shows the Moon as viewed at noon from a position in the
Northern Hemisphere looking south. Note that at times the image shown by the
Moon phase indicator may differ from that of the actual Moon in your area.
• The left-right orientation of the Moon phase is reversed when viewing from the
Southern Hemisphere or from a point near the equator.
After some time, battery power will recover and RECOVER will disappear, indicating
that the above functions are enabled again.
Charging Precautions
Moon Phases and Moon Age
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to a lower temperature.
The Moon goes through a regular 29.53-day cycle during which it appears to wax and
wane due to how the Sun illuminates the Moon and the relative positioning of the
Earth, Moon, and Sun. The greater the angular distance between the Moon and the
Sun, the more we see illuminated.
*
The angle to the Moon in relation to the direction at which the Sun is visible from the
Earth.
*
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it
to become quite hot.Take care when handling the watch to avoid burn injury.
The watch can become particularly hot when exposed to the following
conditions for long periods.
This watch perform a rough calculation of the current Moon age starting from day 0 of
the moon age cycle. The actual Moon age average cycle is 29.53 days, but this can
vary anywhere from –1 day to +1 day for specific months. Since this performs
calculations using integer values only (no fractions), the margin for error of the
displayed Moon age is ±2 days.
• On the dashboard of a car parked in direct sunlight
• Too close to an incandescent lamp
• Under direct sunlight
Tide Graph
The black bar on the watch’s tide graph indicates the current tide.
Charging Guide
After a full charge, timekeeping remains enabled for up to about nine months, while
the watch is used under the conditions described below.
Operating Conditions
• Watch is not exposed to light
Low tide
High tide
• Display on 18 hours per day, sleep state 6 hours per day
• 1 backlight operation (1.5 seconds) per day
• 10 seconds of alarm operation per day
• 1 countdown timer operation per day
Tidal Movements
Tides are the periodic rise and fall of the water of oceans, seas, bays, and other
bodies of water caused mainly by the gravitational interactions between the Earth,
Moon and Sun. Tides rise and fall about every six hours. The tide graph of this watch
indicates tidal movement based on the Moon’s transit over a meridian and the lunitidal
interval. The lunitidal interval differs according to your current location, so you must
specify a lunitidal interval in order to obtain the correct tide graph readings.
Charge Times
Exposing the watch to light for the periods shown below each day restores the power
used by the above operating conditions.
Exposure Level (Brightness)
Outdoor Sunlight (50,000 lux)
Approximate Exposure Time
5 minutes
Lunitidal Interval
Theoretically, high tide is at the Moon’s transit over the meridian and low tide is about
six hours later. Actual high tide occurs somewhat later, due to factors such as
viscosity, friction, and underwater topography. Both the time differential between the
Moon’s transit over the meridian until high tide and the time differential between the
Moon’s transit over the meridian until low tide are known as the “lunitidal interval.”
When setting the lunitidal interval for this watch, use the time differential between the
Moon’s transit over the meridian until high tide.
Sunlight Through a Window (10,000 lux)
24 minutes
Daylight Through a Window on a Cloudy Day
(5,000 lux)
48 minutes
Indoor Fluorescent Lighting (500 lux)
8 hours
• Stable operation is promoted by frequent charging.
Auto Return Feature
RecoveryTimes
If you leave a screen with flashing digits on the display for two or three minutes without
performing any operation, the watch automatically saves any settings you have made
up to that point and exits the setting screen.
The table below shows the amount exposure that is required to take the battery from
one level to the next.
Exposure Level
(Brightness)
Approximate Exposure Time
Data and Setting Scrolling
Level 5 Level 4
Level 3 Level 2
Level 1
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls through the data at high speed.
Outdoor Sunlight (50,000 lux)
65 minutes
4 hours
18 hours
98 hours
4 hours
Sunlight Through a Window
(10,000 lux)
19 hours
Daylight Through a Window
on a Cloudy Day (5,000 lux)
7 hours
– – –
– – –
Indoor Fluorescent Lighting
(500 lux)
60 hours
• The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
4
Operation Guide 2532
Timekeeping
GMT Differential
Standard Time DST/Summer
Site
Longitude
Latitude
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to 00 without changing the minutes.
LONDON
LOS ANGELES
MADRID
0.0
–8.0
1.0
1.0
–7.0
2.0
0°E
118°W
4°W
121°E
145°E
99°W
80°W
9°E
56°W
74°W
59°E
177°E
37°E
167°E
90°W
74°W
165°W
166°E
171°W
80°W
150°W
2°E
116°E
105°E
62°W
168°E
24°W
126°E
47°E
52°N
34°N
40°N
15°N
38°S
19°N
26°N
45°N
35°S
46°N
24°N
18°S
1°S
• With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and no indicator appears for times in the range of
midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
MANILA
8.0
9.0
MELBOURNE
MEXICO CITY
MIAMI
10.0
–6.0
–5.0
1.0
11.0
–5.0
–4.0
2.0
• The year can be set in the range of 2000 to 2039.
• The watch’s built-in full automatic calendar automatically makes allowances for
different month lengths and leap years. Once you set the date, there should be no
reason to change it except when battery power drops to Level 5.
MILAN
MONTEVIDEO
MONTREAL
MUSCAT
–3.0
–5.0
4.0
–2.0
–4.0
5.0
Backlight Precautions
• The electro-luminescent panel that provides illumination loses power after very long
NADI
12.0
3.0
13.0
4.0
use.
NAIROBI
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
NAURU ISLAND
NEW ORLEANS
NEW YORK
NOME
12.0
–6.0
–5.0
–9.0
13.0
–5.0
–4.0
–8.0
12.0
–10.0
–4.0
–9.0
2.0
1°S
30°N
41°N
64°N
22°S
14°N
9°N
• The watch may emit an audible sound whenever the display is illuminated. This is
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
• The backlight automatically turns off whenever an alarm sounds.
• Frequent use of the backlight runs down the battery.
NOUMEA
11.0
PAGO PAGO
PANAMA CITY
PAPEETE
–11.0
–5.0
–10.0
1.0
Auto light switch precautions
18°S
49°N
32°S
12°N
11°N
18°S
15°N
39°N
25°N
42°N
38°N
33°S
24°S
48°N
38°N
31°N
1°N
59°N
34°S
25°N
36°N
48°N
49°N
48°N
18°N
41°S
50°N
• Wearing the watch on the inside of your wrist and movement or vibration of your arm
can cause the auto light switch to activate and illuminate the display. To avoid
running down the battery, turn off the auto light switch whenever engaging in
activities that might cause frequent illumination of the display.
PARIS
PERTH
8.0
9.0
PHNOM PENH
PORT OF SPAIN
PORT VILA
PRAIA
PYONGYANG
RIYADH
7.0
8.0
• The backlight may not light if the face of the watch is
–4.0
11.0
–1.0
9.0
–3.0
12.0
0.0
10.0
4.0
More than 15 degrees
too high
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• The backlight turns off in about one second, even if you
keep the watch pointed towards your face.
3.0
• Static electricity or magnetic force can interfere with
proper operation of the auto light switch. If the backlight
does not light, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back
toward you again. If this does not work, drop your arm
all the way down so it hangs at your side, and then bring
it back up again.
ROME
1.0
2.0
13°E
SAN FRANCISCO
SANTIAGO
SAO PAULO
SEATTLE
–8.0
–4.0
–3.0
–8.0
9.0
–7.0
–3.0
–2.0
–7.0
10.0
9.0
122°W
71°W
47°W
122°W
127°E
121°E
104°E
18°E
151°E
121°E
140°E
107°E
123°W
16°E
SEOUL
• Under certain conditions, the backlight may not light until
about one second after you turn the face of the watch
towards you. This does not necessarily indicate
malfunction of the backlight.
SHANGHAI
SINGAPORE
STOCKHOLM
SYDNEY
8.0
8.0
9.0
1.0
2.0
10.0
8.0
11.0
9.0
Site Data List
TAIPEI
TOKYO
9.0
8.0
10.0
9.0
GMT Differential
Standard Time DST/Summer
ULAANBAATAR
VANCOUVER
VIENNA
VIENTIANE
WELLINGTON
WINNIPEG
Site
ABIDJAN
ABU DHABI
ADDIS ABABA
ADEN
AMSTERDAM
ANCHORAGE
ATHENS
AZORES
BANGKOK
BEIJING
BEIRUT
BOGOTA
Longitude
Latitude
–8.0
1.0
–7.0
2.0
0.0
4.0
3.0
3.0
1.0
–9.0
2.0
–1.0
7.0
8.0
2.0
–5.0
–5.0
–3.0
–3.0
2.0
–4.0
0.0
–6.0
12.0
0.0
1.0
5.0
4.0
4.0
2.0
–8.0
3.0
0.0
8.0
9.0
4°W
54°E
39°E
45°E
5°E
5°N
24°N
9°N
7.0
8.0
103°E
175°E
97°W
12.0
–6.0
13.0
–5.0
13°N
52°N
61°N
38°N
38°N
14°N
40°N
34°N
5°N
42°N
16°S
35°S
34°S
11°N
34°N
42°N
44°S
15°N
149°W
24°E
25°W
101°E
116°E
36°E
74°W
71°W
48°W
58°W
18°E
67°W
8°W
• Based on data as of 2003.
Lunitidal Interval List
3.0
Site
Lunitidal
Site
Lunitidal
–4.0
–4.0
–2.0
–2.0
3.0
–3.0
1.0
–5.0
13.0
1.0
Interval
5:40
Interval
5:20
2:00
1:10
9:20
10:30
2:10
7:30
8:30
6:40
3:00
0:10
4:20
1:20
5:10
4:50
BOSTON
BRASILIA
ANCHORAGE
BANGKOK
BOSTON
BUENOS AIRES
CASABLANCA
DAKAR
GOLD COAST
HAMBURG
HONG KONG
HONOLULU
JAKARTA
LIMA
4:40
LISBON
BUENOS AIRES
CAPE TOWN
CARACAS
CASABLANCA
CHICAGO
CHRISTCHURCH
DAKAR
DALLAS
FORT WORTH
DAMASCUS
DENVER
DETROIT
DHAKA
11:20
6:00
1:30
LONDON
LOS ANGELES
MANILA
7:40
8:30
MELBOURNE
MIAMI
88°W
173°E
17°W
4:50
NOUMEA
9:10
3:40
0:00
PAGO PAGO
PANAMA CITY
PAPEETE
–6.0
–5.0
97°W
33°N
2.0
–7.0
–5.0
6.0
4.0
0.0
–7.0
–7.0
1.0
10.0
10.0
1.0
7.0
2.0
8.0
–10.0
–6.0
2.0
7.0
3.0
3.0
–6.0
–4.0
7.0
5.0
1.0
–6.0
–6.0
2.0
11.0
11.0
2.0
8.0
3.0
9.0
–9.0
–5.0
3.0
8.0
4.0
36°E
105°W
83°W
90°E
55°E
6°W
114°W
106°W
9°E
154°E
145°E
10°E
106°E
25°E
114°E
158°W
95°W
29°E
107°E
39°E
67°E
102°E
48°E
68°W
115°W
77°W
9°W
34°N
40°N
42°N
24°N
25°N
53°N
54°N
32°N
50°N
28°S
13°N
54°N
21°N
60°N
22°N
21°N
30°N
41°N
6°S
22°N
25°N
3°N
29°N
17°S
36°N
12°S
39°N
JEDDAH
KARACHI
SINGAPORE
SYDNEY
6:30
SEATTLE
10:10
10:20
8:40
SHANGHAI
VANCOUVER
WELLINGTON
DUBAI
DUBLIN
• Based on data as of June 2001.
EDMONTON
EL PASO
FRANKFURT
GOLD COAST
GUAM
HAMBURG
HANOI
HELSINKI
HONG KONG
HONOLULU
HOUSTON
ISTANBUL
JAKARTA
JEDDAH
KARACHI
KUALA LUMPUR
KUWAIT
5.0
8.0
3.0
–4.0
–8.0
–5.0
0.0
6.0
9.0
4.0
–3.0
–7.0
–4.0
1.0
LA PAZ
LAS VEGAS
LIMA
LISBON
5
|