Module No. 1699/1919
1699/1919-1
GENERAL GUIDE
• The operational procedures for Module 1699 and 1919 are identical.All of the illustrations
in this manual show Module 1699.
• Press M to change from mode to mode. Each mode is explained in detail on the
following pages.
Beat Counter Mode
Stopwatch Mode
Timekeeping Mode
A
M
B
C
A
M
B
C
Press M
Alarm Mode
L
L
[Module 1919]
[Module 1699]
To turn the EL alarm on and off
TIMEKEEPING MODE
In the Timekeeping Mode, hold down B for about two seconds to toggle the EL alarm
on (FLASH indicator displayed) and off (FLASH indicator not displayed).
• When the EL alarm is on, the backlight flashes while the daily alarm and hourly time
signal tones are sounding. Also, the backlight stays on for about five seconds instead
of the normal two seconds.
• When an auto light switch operation causes the backlight to turn on while the EL alarm
is turned on, the backlight stays lit for about two seconds, and then flashes for two
seconds.
To set the time and date
Day of week
1. Hold down A while in the Timekeeping Mode until the
seconds digits start to flash on the display. The seconds
flash because they are selected.
Month – Day
A
B
2. Press M to change the selection in the following
sequence.
Seconds
About the Auto Light Switch
M
C
While the auto light switch is turned on, the backlight automatically lights for about two
seconds whenever you position your wrist as described below. Avoid wearing the watch
on the inside of your wrist. Doing so causes the auto light switch to operate when it is not
needed, which shortens battery life.
Hour : Minutes
PM indicator
Seconds
Hour
Minutes
Moving the watch to a position that is parallel to the ground and then tilting it towards
you more than 40 degrees causes the backlight to illuminate.
12/24-Hour
Format
Day
Month
Year
3. While the seconds digits are selected (flashing), press C to reset the seconds to 00.
• If you press C while the seconds count is in the range of 30 to 59, the seconds are
reset to 00 and 1 is added to the minutes. If the seconds count is in the range of 00 to
29, the minutes count is unchanged.
4. While any other digits (besides seconds) are selected (flashing), press C to increase
the number. While the 12/24-hour setting is selected, press C to switch between the
two formats.
More than
Parallel to
ground
40°
• Holding down C changes the current selection at high speed.
• When the 12-hour format is selected, the12H indicator appears on the display. With
the 12-hour format, the P (PM) indicator appears on the display to indicate “p.m.”
times. There is no indicator for “a.m.” times.
• Selecting the 24-hour format causes the 24H and the 24 indicators to appear on the
display.
5. After you set the time and date, press A to return to the Timekeeping Mode.
• The day of the week is automatically set in accordance with the date.
• The date can be set within the range of January 1, 1995 to December 31, 2039.
• If you do not operate any button for a few minutes while a selection is flashing, the
flashing stops and the watch goes back to the Timekeeping Mode automatically.
• The backlight may not illuminate if the face of the watch is more than 15 degrees off
the parallel as shown below. Make sure that the back of your hand is parallel to the
ground.
Parallel to ground
More than 15 degrees
too high
More than 15 degrees
too low
BACKLIGHT FUNCTION
A backlight that uses an EL (electro-luminescent) panel
Auto light switch on indicator
causes the entire display to glow for easy reading in the
dark. An auto light switch causes the EL backlight to turn on
when the watch is angled toward your face for reading. An
EL alarm feature can be turned on so the backlight flashes
whenever an alarm or hourly time signal sounds.
• The auto light switch on indicator is shown on the display
in all modes while the auto light switch is on.
• Static electricity or magnetic force can interfere with proper operation of the auto light
switch. If the auto light switch does not illuminate, try moving the watch back to the
starting position (parallel with the ground) and then tilt it back toward you again. If this
does not work, drop your arm all the way down so it hangs at your side, and then bring
it back up again.
• Under certain conditions the backlight may not light until about one second or less
after turn the face of the watch towards you. This does not necessarily indicate
malfunction of the backlight.
A
B
• The FLASH indicator is shown on the display in all modes
while the EL alarm is on.
M
C
L
Note
Warning!
FLASH indicator
• The backlight of the watch employs an electro-luminescent
(EL) light, which loses illuminating power after very long
use.
• Never try to read your watch when mountain climbing or hiking in areas that are
dark or in areas with poor footing. Doing so is dangerous and can result in
serious personal injury.
• Never try to read your watch when running where there is danger of accidents,
especially in locations where there might be vehicular or pedestrian traffic. Doing
so is dangerous and can result in serious personal injury.
• Never try to read your watch when riding on a bicycle or when operating a
motorcycle or any other motor vehicle. Doing so is dangerous and can result in
a traffic accident and serious personal injury.
• When you are wearing the watch, make sure that its auto light switch is turned
off before riding on a bicycle or operating a motorcycle or any other motor vehicle.
Sudden and unintended operation of the auto light switch can create a distraction,
which can result in a traffic accident and serious personal injury.
• The illumination provided by the backlight may be hard to see when viewed under
direct sunlight.
• The watch will emit an audible sound whenever the display is illuminated. This is caused
by a transformer that vibrates when the EL panel lights up. It does not indicate
malfunction of the watch.
• The backlight automatically turns off whenever an alarm sounds.
To manually turn on the backlight
Pressing L in the Timekeeping, Stopwatch or Alarm Mode causes the backlight to turn
on for about two seconds. Pressing C in the Beat Counter Mode also causes the backlight
to turn on for a fixed amount of time.
• The backlight normally stays on for about two seconds and then turns off automatically.
When the ELalarm is turned on, however, the backlight stays on for about five seconds
instead of two seconds.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down C for one second to turn the auto light switch on
(
displayed) and off (
not displayed).
• In order to protect against running down the battery, the auto light switch is automatically
turned off approximately three hours after you turn it on. Repeat the above procedure
to turn the auto light switch back on if you want.
• The above operations turn on the backlight, regardless of the current auto light switch
and EL alarm settings.
|