Setting Values Cross Reference Table
(The tire size is marked on both sides of the tire.)
CATEYE TOMO XC
TIRE SIZE
20 x 1.75
24 x 1
24 x 3/4 Tubular
24 x 1-1/8 Tubular
24 x 1-1/4
24 x 1.75
24 x 2.00
24 x 2.125
26 x 1(559mm)
26 x 1(650c)
26 x 1.25
26 x 1-1/8 Tubular
26 x 1-3/8
L(cm) TIRE SIZE
L(cm) TIRE SIZE
L(cm)
211
207
209
209
210
211
214
217
216
213
217
218
222
150
175
178
179
191
189
192
196
191
195
195
197
207
210
26 x 1.40
26 x 1.50
26 x 1.75
26 x 1.95
26 x 2.00
26 x 2.1
26 x 2.125
26 x 2.35
27 x 1
27 x 1-1/8
27 x 1-1/4
27 x 1-3/8
650 x 35A
650 x 38A
200
199
202
205
206
207
207
208
215
216
216
217
209
212
650 x 38B
700 x 18C
700 x 19C
700 x 20C
700 x 23C
700 x 25C
700 x 28C
700 x 30C
700 x 32C
700C Tubular
700 x 35C
700 x 38C
700 x 44C
CYCLOCOMPUTER
Model CC-ST200
[with Heavy Duty Wire]
U.S. Pat. Nos. 4636769/4642606/5236759/5226340
and Design Patented
26 x 1-1/2
Copyright© 1999 CATEYE Co., Ltd.
E
CCMSTxch1-991124 Printed in Malaysia 066600035
SPECIFICATIONS
3
Controller ----------------------------------- 4-bit 1-chip Microcomputer (Crystal Controlled Oscillator)
Display -------------------------------------- Liquid Crystal Display
Sensor -------------------------------------- No Contact Magnetic Sensor
Operating Temperature Range ------- 0°C - 40°C (32°F - 104°F)
Applicable Cycle Sizes ------------------ 130cm - 229cm
MOUNTING TO BIKE
The length of the wire ------------------- 70cm
Applicable Fork Diameter -------------- 11ø - 40ø (S:11 - 26ø L:21 - 40ø)
Power Supply ----------------------------- Lithium Battery (CR1620 or CR1616) x 1
Battery Life --------------------------------- Approx. 3 years(The life of the first factory-loaded battery may
be shorter than this period.)
Dimension/Weight ------------------------ 1-15/16" x 1-25/32" x 5/8" (49 x 45 x 16 mm) / 0.74 oz (21 g)
* The specifications and design are subject to change without notice.
LIMITED WARRANTY
1-Year Warranty for Main Unit Only
(Accessories/Attachments and Battery Consumption excluded)
If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of
charge. The service must be performed by Cat Eye Co., Ltd. To return the product, pack it carefully
and remember to enclose the warranty certificate with instruction for repair. Please write or type your
name and address clearly on the warranty certificate. Insurance, handling and transportation charges
to our service shall be borne by person desiring service.
1. Bracket
2. Wire
3. Sensor
7. Sensor Band Rubber Pad
8. Bracket Rubber Pad (2 pcs.)
9. Nylon Tie (3 pcs.)
4. Sensor Bands-A (S)(L) 10. Sensor Band Screw (S)(L)
5. Sensor Bands-B
6. Magnet
(Address for service)
11. Spiral Tube
CO.,LTD.
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan
Attn.: CAT EYE Customer Service Section
Service & Research Address for United States Consumers:
CAT EYE Service & Research Center
•
•
The spokes must run correctly through the
inside the magnet as in fig.1.
1705 14th St. 115 Boulder, CO 80302
magnet
Attach the sensor with Sensor Bands-A-B to
the right fork. Choose a band that fits the fork
diameter (S size for up to 24ø, L for
oversize). If the front fork is thick, use the
longer screw.
Phone : 303-443-4595
Fax : 303-473-0006
Toll Free: 800-5CATEYE
e-mail: [email protected]
sporkes
#169-9731
Heavy Duty Wire and Bracket Sensor Kit
1. Insert the band-B into the slit of the band-
A, and put the rubber pad inside of the
band-A(fig. 2). Adjust the length in order
that the screw-fastening part of the bands
are parallel when mounted to the fork(fig.
3). *To pull out the band B from band A,
tug strongly.
2. Mount the adjusted bands to the fork along
with the sensor, by temporarily tightening
the screw(fig. 4).
Fig.1
sensor band B
rubber pad
#169-9771
sensor band B
Bracket Sensor Kit for Extra Large Fork
sensor
band A
Fig.2
rubber pad
sensor band A
sensor band A
3. Align the magnet's center and the sensor's
marking line(fig. 5), and make sure of
2mm clearance between the magnet and
sensor (fig. 6). Then tighten the screw
securely. Cut the excess of the band-B
with a nipper or the like.
Secure the wire with nylon ties as shown in
fig. 7. Wind the wire round the outer cable
and wrap these wires with the spiral tube.
Adjust the length of the wire. Loosen the wire
in the area marked with the arrow so that the
wire does not hinder handlebar operation.
Use either 1mm- or 2 mm-thick pads if
necessary, according to handlebar diameter.
Attach the bracket close to the handlebar
stem (fig. 8).
Fig.3
parallel
#169-6168
Bracket Sensor Kit for Aero Bar
screw
fork
Fig.4
sensor
•
markingline
of sensor
#169-6167
center of
magnet
Center Mount Bracket Kit
sensor
•
•
Fig.5
#169-6169
about 2mm
Slide main unit onto the bracket from front
until it clicks into position. To remove, pull it
off forward while pushing down the lever. (fig.
9)
Stem Mount Bracket Kit
Fig.6
magnet
outer cable
•Test
spiral tube
Mount main unit. If main display does not show
any figures, press either M button or S/S button
to release from power saving function. Spin the
wheel to check if sensor pulse symbol flashes.
If not, adjust relative positions of magnet and
sensor following the instructions.
#169-9750
#169-9751
Attachment Kit (For Heavy Duty Wire)
Attachment Kit (For TOMO XC)
nyron ties
wire
#166-5120
#169-6180
Wheel Magnet
Lithium Battery(CR1620)
Fig.7
lever
bracket
Fig.9
Slide the main unit onto the bracket from
front until it clicks into position. To remove
it, pull it off forward while pushing down the
lever. (Fig.9)
rubber pad
Fig.8
|