Chamberlain Stud Sensor PIR2300R User Manual

®
Model PIR2300R  
Wireless Pedestrian & Vehicle Sensor  
Overview  
Step 2  
The Wireless Pedestrian & Vehicle Sensor is a  
Passive Infra-Red sensor that detects movement of  
people and vehicles, while allowing small animals to  
pass through undetected. Each PIR Motion Sensor  
has its own unique ID, for a secure radio link.  
Base Station (not provided) can learn the signals of  
up to four PIR Motion Sensors. The Base Station will  
give a single beep for the first Sensor that it learns, a  
double beep for the second, and so forth. Additionally,  
multiple Base Stations can work with the same PIR  
Motion Sensor to sound in different places.  
Carton Inventory  
Install 4 AA Alkaline batteries (not provided). (Lithium  
batteries recommended for colder environments.)  
LED light will flash.  
Swivel Bushing  
Switch Settings  
Passive Infra-Red (PIR) Motion Sensor  
Antenna  
PIR Sensor  
Sun/Rain Shield  
Mounting Plate  
PIR Motion Sensor  
Assembly & Test  
Step 1  
Switch #1  
Test  
Button  
Switch #2  
Switch #1:.  
OFF  
ON  
15' Detection Range  
30' Detection Range  
(Default)  
OFF  
ON  
Switch #2:  
OFF  
ON  
Low Sensitivity  
High Sensitivity  
(Default)  
1
2
Attach PIR Motion Sensor box to mounting plate with  
large silver screw. Tighten screw until PIR Motion  
Sensor stays in place when repositioned.  
NOTE: To avoid unwanted detection of small animals  
move Switch #2 to OFF.  
1
 
Vehicle Alert Installation: For cars, the best  
mounting position is about 4' high, between 10-20'  
back, and angled to see the back of car after passing  
the sensor.  
10' - 20'  
3' - 5'  
Troubleshooting  
The PIR Motion Sensor lights up, but the Base  
Station does not respond.  
The PIR Motion Sensor must be programmed to Base  
Base Station beeps every ten minutes.  
The battery in the Base Station is low. Replace with  
9-Volt battery or operate it using AC Adapter.  
Station (See Step 5).  
Ensure Base Station is on and is not muted.  
If the green power light is not lit or is flashing, press  
the Mute Button on the top of the Base Station to  
wake it up.  
If the green power is illuminated, look at the two small  
white Base Station switches next to the Learn Button.  
The #1 Dip Switch should be down, towards the  
circuit board. If it is up, the Base Station has been  
muted. If the Base Station signals when you press the  
Learn Button, it is not muted.  
The Alert is not getting expected transmission  
range.  
Keep both antennas vertical and keep PIR Motion  
Sensor antenna away from trees and metal objects.  
Ensure Base Station is in clearest possible sight of  
the PIR Motion Sensor. The less objects between the  
devices, the longer the range.  
Base Station is not very loud.  
An accessory such as a bell, buzzer, or light can be  
attached to the relay switch. The relay switch can  
handle up to 120 AC volts at 10 amps. The accessory  
device will need a separate power supply.  
The accessories can be purchased at any electronics  
store.  
PIR Motion Sensor is detecting motion only part  
of the time.  
To detect cars, it is best to mount PIR Motion Sensor  
at height of car’s motor and have it between ten and  
twenty feet from the road. Swivel sensor as needed.  
NOTE: The manufacturer is not responsible for any  
radio or TV interference caused by unauthorized  
modifications to this equipment. Changes or  
modifications not expressly approved by the  
manufacturer could void the user’s authority to  
operate the equipment.  
The Alert is giving false alarms.  
Check for moving tree branches or insects in sensor  
window. PIR sensor can also be triggered by light  
shining directly in sensor window, such as reflected  
sunlight, or motion in front of a light source.  
It is possible that condensation has built up on the  
sensor. Wipe condensation from PIR Motion Sensor  
with cotton swab. Let it sit inside for a few hours,  
open to the air, without the batteries and it should  
correct itself.  
Check Sensor Switches on PIR Motion Sensor. See  
Switch Settings.  
3
 
FOR TECHNICAL SUPPORT DIAL OUR TOLL FREE NUMBER:  
1-800-528-9131  
www.chamberlain-DIY.com  
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this  
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the battery.  
THERE ARE NO OTHER USER SERVICEABLE PARTS.  
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following  
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undesired operation.  
© 2008, The Chamberlain Group Inc.  
All Rights Reserved  
114A3508B  
 

BenQ Projector PB6210 User Manual
Black Box Computer Hardware KV1720A User Manual
Bogen Portable Speaker HFSF1 User Manual
Bravetti Cookware CW23HCH User Manual
Briggs Stratton Air Cleaner 128600 User Manual
Brother Sewing Machine 882 D00 User Manual
BUSH Flat Panel Television IDLED2202DVD User Manual
Campbell Hausfeld Marine Battery IB3003 User Manual
Campbell Hausfeld Pressure Washer PW132000AV User Manual
Chauvet Utility Trailer A User Manual