®
CLICKER
MODEL KLIK1U
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to
operate, or play with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and
there are no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit
anyone to cross path of moving gate or door.
UNIVERSAL GARAGE DOOR OPENER REMOTE CONTROL
Read instructions thoroughly BEFORE beginning.
Start with garage door closed. Identify garage door opener type - Smart/Learn button
or DIP Switch. Smart/Learn button or DIP Switches are located on motor unit or
external receiver. Refer to owner’s manual if necessary.
Clicker products are intended to be used only with garage door openers
manufactured after 1993 that utilize photo-eyes safety sensors. These are always
located on or near the bottom of the door track. If your garage door does not
have the sensors attached and working, the opener is not compliant with current
federal safety regulations and should be replaced.
STOP
Proceed with instructions according to your type of garage door opener.
SMART/LEARN BUTTON
DIP SWITCH
CHART A
CHART B
See Chart A to determine
See Chart B to determine
1
1
# of times to
press button
Type/Color of
Smart/Learn
# of times to
press button
# of times to press
button and write in blank
on Step 5.
# of times to press
button and write in blank
on Step 5.
Brand
Year
Brand
Description
Year
®
®
1
2
3
4
Linear
Mega-Code
Orange/Red
Purple
'97-Current
'97-'03
11
Chamberlain *
9 Position
'90-'92
®
Chamberlain *
9 Position
Canada
®
12
Chamberlain *
'83-'89
®
Chamberlain *
'05-Current
'93-'96
®
13
14
15
Genie
12 Position
'85
®
Chamberlain *
Green
®
Linear Multicode 10 Position
'76
®
Genie
5
6
Intellicode
Intellicode
'95-Current
'93-Current
®
®
®
Overhead Door
2
3
2
Chamberlain
8 Position
10 Position
9 Position
8 Position
7 Position
'83-'89
®
Genie **
Stanley/
16
17
18
19
'76
®
Overhead Door
Multicode
®
®
7
Stanley
Secure Code
Yellow
'98
Genie
'85
®
®
8
Chamberlain *
'11-Current
'99
Linear
'76
®
®
Moore-O-Matic
9
Wayne Dalton
Rolling Code
9 Position
®
®
Chamberlain
'83-'89
11
Chamberlain
'90-'92
*NOTE: LiftMaster, Do-It, Master Mechanic, Raynor, True Value and Sears Craftsman are compatible with
Chamberlain technology.
Motor
Unit
3
Existing
Remote
Clicker
Remote
SMART/LEARN BUTTON
DIP SWITCH
OR
ON
Press program button until
LED lights.
Match DIP switches. Turn
extra switches OFF.**
1
2
3
KG
KG
4
1
2
3
4
KG
KG
Motor Unit
Press program button
until LED lights.
Press and release the Smart/
Learn button.
5
5
NOTE: Your opener may
appear different and you may
have to remove the light lens
to access the learn button.
Select a button to program.
Press button
times
Select a button to program.
ensuring LED stops flashing
after each press. Code is
accepted when door
activates.
Press button
times ensuring
LED Indicator
LED stops flashing after each
press. Code is accepted when
one of the following occurs:
Button 2
Button 1
Click
OR
OR
Program Button
DIP Switches
6
NOTE: If there are problems
programming to button 1,
program to button 2.
Press program button.
Battery
6
Battery Cover
7
Press program button.
REMOTE CONTROL BATTERY
Programming complete. Press
selected button to test. If unit
does not work, return to Step 3.
7
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
NOTE:
ON
Programming complete. Press
selected button to test. If unit
does not work, return to Step 3.
2 Position DIP Switch:
If programming fails reverse
DIP switches (OFF to ON and
ON to OFF).
• DO NOT recharge, disassemble, heat above 100° C (212° F) or
incinerate.
Product Registration and Troubleshooting
Dispose of batteries properly. Replace ONLY with 3V2032 coin batteries.
**3 Position DIP Switch:
For Chamberlain remotes DO NOT
use the “0” position, use “+” or “-”. If you already have
a 3-button remote, DIP switch #1 must be set to “-” if
the large button is to open the door. It may be
necessary to reprogram original remote controls.
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of this receiver
and/or transmitter are prohibited, except for changing the code setting or replacing the battery. THERE ARE
NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group.
Genie and Intellicode are trademarks of GMI Holdings, Inc. Overhead Door is a
Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation.
Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears &
Roebuck. Stanley is a Trademark of The Stanley Works. Wayne Dalton is a trademark
of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.
© 2011, Clicker Corporation
All Rights Reserved
114A3485G
|