Chauvet Work Light TFX 950CM User Manual

TFX-950CM

Stage Wash™ 950

USER MANUAL

Chauvet, 3000 N 29^thCt, Hollywood, FL 33020 U.S.A

(800) 762-1084 – (954) 929-1115

FAX (954) 929-5560

www.chauvetlighting.com

BEFORE YOU BEGIN

What is included



1 x Stage Wash™ 950CM (TFX-950CM)

Power cord with plug

3 x EHM 300w 120v or 3 x EHM2 300w 230v lamps

Warranty Card & Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that

all parts are present, and have been received in good condition. Notify the shipper immediately and

retain packing material for inspection if any parts appear damaged from shipping or the carton itself

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture

must be returned to the factory, it is important that the fixture be returned in the original factory box

and packing.

AC Power

To determine the power requirements for a particular fixture, see the label affixed to the back plate of

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average

current draw under normal conditions. All fixtures must be powered directly off a switched circuit and

cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer

channel is used solely for a 0% to 100% switch. Before applying power to a

AC Voltage Switch

fixture, check that the source voltage matches the fixture’s requirement. Check

the fixture or device carefully to make sure that if a voltage selection switch

exists that it is set to the correct line voltage you will use.

Warning!

Verify that the power select switch on your unit matches the

line voltage applied. All fixtures must be connected to circuits

with a suitable Earth Ground.

Safety Instructions

Please read these instructions carefully, which includes important information about the installation,

usage and maintenance?



Please keep this User Guide for future consultation. If you

sell the unit to another user, be sure that they also receive

this instruction booklet.



Secure fixture to fastening device using a safety chain.

Never carry the fixture solely by its head. Use its carrying

handles.

Maximum ambient temperature is Ta: 40°. Do not operate

fixture at temperatures higher than this.

In the event of serious operating problem, stop using the

unit immediately. Never try to repair the unit by yourself.

Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest

authorized technical assistance center. Always use the

same type spare parts.

Don’t connect the device to a dimmer pack.

Make sure power cord is never crimped or damaged.

Never disconnect power cord by pulling or tugging on the

cord.

Always make sure that you are connecting to the proper

voltage and that the line voltage you are connecting to is

not higher than that stated on decal or rear panel of the

fixture.

This product is intended for indoor use only!

To prevent risk of fire or shock, do not expose fixture to

rain or moisture. Make sure there are no flammable

materials close to the unit while operating.

The unit must be installed in a location with adequate

ventilation, at least 50cm from adjacent surfaces. Be sure

that no ventilation slots are blocked.



Always disconnect from power source before servicing or

replacing lamp or fuse and be sure to replace with same

lamp source.



Avoid direct eye exposure to lamp while it is on.

Caution!

There are no user serviceable parts inside the unit. Do not open the housing or

attempt any repairs yourself. In the unlikely event your unit may require service,

please contact CHAUVET.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

INTRODUCTION

Features



2-4 channel DMX RGB color wash fixture

Operating modes:

RGB Mode: Full RGB mix plus dimmer (4 channels)

C&B Mode: Color selection (40 presets) and dimmer (2 channels)

RGB & Chase Mode: 7 distinct operating modes (4 channels)

- RGB mix, 8-pattern auto, 8-pattern sound, auto-chase, sound-chase, 40-color auto or sound



Individual channel controls may include;

- Red 0-100%, color selection or mode select

- Green or Red 0-100%, dimmer 0-100%

- Blue or Green 0-100%, fade time

- Dimmer 0-100%, speed time



900 watts of total brightness

Built in beat activated and automatic programs (stand-alone)

Barn doors

Sound sensitivity knob

Double bracket yoke doubles as floor stand

Linkable via Master/Slave

Fan cooled

DMX Channel Summary

RGB Mode

Channel

Function

Red

Green

Blue

Dimmer

C&B (Color & Brightness) Mode

Channel

Function

Color Selection

Dimmer

Combined RGB & Chase Mode

Channel

Function

Control Mode

Red or Dimming

Green or Fade

Blue or Speed

For complete channel listing see DMX Values in the Appendix section.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Introduction

Product Overview

LED status

window

DMX channel

values and brief

instructions

Control panel

buttons

Fan

DMX Input

connector

Sound

sensitivity knob

Built in

microphone

Voltage

Selector Switch

IEC power

connector for

power cable

Fuse

compartment

DMX Output

connector

Foot controller

connector for

TFX-SWF

TFX-950CM User Manual

Revision: 2006-01-20/16:37

SETUP

Lamp

You will need to install a lamp prior to the initial operation of the fixture. Three EHM 300W halogen

lamps are included.

Warning!

When replacing the lamp, please wait 15 minutes after powering down to allow the

unit to cool down! Always disconnect from main power prior to lamp replacement.

Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp

with alcohol and wipe it with a lint free cloth before installation.

LAMP INSTALLATION

TFX-950CM Lamp Installation

1) Remove the 2 screws as illustrated in Figure 3,

located on the front of the fixture and lift the entire

cover plate until lamp reflectors are exposed.

2) The linear lamp is held in place by tension provided by

springs inside of both ceramic socket ends. It is

important to proceed with lamp removal and

Remove these 2 screws

replacement very delicately.

3) Hold linear lamp with a napkin and push in the

direction of either of the two ends to relieve tension on

the opposite end. Then pull end of lamp upwards to

remove from socket.

4) To replace lamp, follow the same procedure as above

to insert lamp into the socket.

5) Lower the cover plate and replace both screws.

6) No lamp alignment is necessary for this fixture.

Lamps exposed

Power

Your product is equipped with switch-selectable AC power

Slide switch up or down

setting.

depending on your line voltage.

Warning!

Verify that the power select switch on your unit

matches the line voltage applied. All fixtures must

be connected to circuits with a suitable Earth

Ground.



To determine the power requirements for a particular fixture,

see the label affixed to the back plate of the fixture or refer to

the fixture’s specifications chart.



A fixture’s listed current rating is its average current draw under normal conditions.

All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat (variable

resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0% to 100%

switch.



Before applying power to a fixture, check that the source voltage matches the fixture’s requirement.

All fixtures must be connected to circuits with a suitable Earth Ground.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Setup

Mounting

ORIENTATION

This fixture may be mounted in any position provided there is adequate room for ventilation.

RIGGING

Hanging Clamp

It is important never to obstruct the fan or vents pathway. Mount the

fixture using, a suitable “C” or “O” type clamp. Adjust the angle of the

fixture by loosening both knobs and tilting the fixture. After finding

the desired position, retighten both knobs.



When selecting installation location, take into consideration lamp

replacement access and routine maintenance.



Safety cables should always be used.

Note!

Never mount in places where the fixture will be exposed to rain, high

humidity, extreme temperature changes or restricted ventilation.

Clamp is sold separately.

DOUBLE BRACKET YOKE (FLOOR STAND)

The TFX-950CM can also be positioned on the floor using its double bracket yoke. This product gets

extremely hot under normal operation and you should take extreme care to avoid any contact what

so ever with the fixture while in use. Be sure to keep all traffic at least 4 feet away from the fixture’s

position.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

OPERATING INSTRUCTIONS

Operating Modes

The TFX-950CM can be operated in three ways.



A stand-alone mode will listen to sound and run through its diverse range of built in programs. An

optional TFX-SWF wired controller provides simple remote control.

Master/Slave mode will allow the command of up to as many units you want in a synchronized light

show to the sound.

DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be controlled

individually using any universal DMX-512 controller.

Stand Alone Mode

The Stand Alone mode is

activated by setting the TFX-

950CM to either AUDIO

(Sound Active) or AUTO

(Automatic) mode. The built in

programs consist of a color

chase and depending on the

mode, two or three parameters

can be modified as described

next.

AUDIO

RGB&D

C & B

DMX Signal

Received

F:0:0:0

AUTO

MODE

DOWN

AUDIO MODE (ALSO SOUND-ACTIVE)

1) A steady hold of the MODE button will change the operating mode once then release the button.

2) Repeat step 1 until you arrive at the AUDIO operating mode, as indicated by the LED next to the

label.

3) Two parameters will now become available for the AUDIO mode. Press the MODE button

quickly to toggle between parameters.

- F (for Fade time 0 ~ 100%)

- D (for Dimming 0 ~ 100%)

4) Use the UP and DOWN buttons to change values for each respective parameter.

AUTOMATIC MODE

1) A steady hold of the MODE button will change the operating mode once then release the button.

2) Repeat step 1 until you arrive at the AUTO operating mode, as indicated by the LED next to the

label.

3) Three parameters will now become available for the AUTO mode. Press the MODE button

quickly to toggle between parameters.

- F (for Fade time 0 ~ 100%)

- D (for Dimming 0 ~ 100%)

- S (for Speed 0 ~ 100%)

4) Use the UP and DOWN buttons to change values for each respective parameter.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Operating Instructions

Master/Slave

The Master/Slave mode will allow you to link up to as many units you want in a daisy chain fashion. In

this mode, the first unit in the daisy chain will automatically command all other units following. An

optional TFX-SWF controller connected to the first unit in the chain will allow enhanced control

functions.

MASTER/SLAVE SETTINGS

1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector

of the first fixture.

2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,

proceed to connect from the output as stated above to the input of the following fixture and so on

as illustrated below in figure “Daisy Chain Connection”.

Daisy Chain Connection

Optional Controller

Controller not required for

Master/Slave operation

Note!

For additional information on linking fixtures read under section “DMX Primer”

DMX Mode

Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to

customizing or creating a show. In this mode you will be able to control each individual trait of the

fixture independently.

SETTING THE STARTING ADDRESS

This DMX mode enables the use of a universal DMX controller device. Each fixture requires a "start

address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data

on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels

of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,

102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate

the start address selected for future reference.

If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping

to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that

will help you understand its use.

There are three different DMX

channel configurations on the

AUDIO

RGB&D

C & B

Stage Wash. Each mode or

configuration allows the user to

control the fixure in a different

manner using a universal DMX

controller.

DMX Signal

Received

A:0:0:1

AUTO

MODE

DOWN

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Operating Instructions

RGB&D MODE

All three lamps are individually dimmable giving the user

the ability to customize or create the color of choice. This

mode offers the user complete freedom.

Channel

Function

Red

Green

Blue

1) A steady hold of the MODE button will change the

operating mode once then release the button.

Dimmer

2) Repeat step 1 until you arrive at the RGB&D

operating mode, as indicated by the led next to the

label.

3) The display will now read parameter A: which represents the DMX channel address value. Use

the UP and DOWN buttons to change values.

C&B MODE

This is called the Color and Brightness mode. Use channel

Channel Function

1 to move across the RGB spectrum.

Spectrum Color Mix

Dimmer

1) A steady hold of the MODE button will change the

operating mode once then release the button.

See Color Mix Table in the

appendix section.

2) Repeat step 1 until you arrive at the C&B operating

mode, as indicated by the led next to the label.

3) The display will now read parameter A: which

represents the DMX channel address value. Use the UP and DOWN buttons to change values.

RGB & CHASE MODE

This is the most diverse operating mode the Stage Wash

Channel Function

has to offer. It allows individual RGB mix control when

Control Mode

Red or Dimming

Green or Fade

Blue or Speed

needed while still maintaining the ability to run built in

automated chase programs.

1) A steady hold of the MODE button will change the

operating mode once then release the button.

2) Repeat step 1 until both the RGB&D and the C&B led

turn on.

3) The display will now read parameter A: which represents the DMX channel address value. Use

the UP and DOWN buttons to change values.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Operating Instructions

TFX-SWF Easy Controller (Optional)

The TFX-SWF Foot Controller is used only in master/slave mode. Connect the 8-pin connector of the

foot controller into its respective connector on the first unit in the daisy chain. The table below

describes the functions of the TFX-SWF Controller.

TFX-SWF BUTTONS

TFX-SWF Foot Controller

Stand By Mode

Function

TFX-SWF

Blackout Auto

Fixtures will run built in programs

Led 1: Off

Led 2: Off

automatically

STAND-BY

FUNCTION

MODE

Audio

Led 1: Off

Led 2: On

Fixtures will run built in programs to

the sound.

Manual

Full/CB:

Led 1: On

Led 2: Off

Hold: pedal to set to Full On

Bump: Pedal to set dimming levels

Manual

Full/CB:

Led 1: On

Led 2: On

Hold: pedal to set dimming levels

Release: Pedal to set to Full On

TFX-CONPK Stage Wash™ Controller Pack (Optional)

The TFX-CONPK is a package that includes the TFX-32CON which is an enhanced dedicated

controller for the TFX-950CM, TFX-64CM and TFX-1550CM fixtures. The TFX-32F foot controller is

also included for hands-free operation.

The TFX-32CON provides the following features:



9 different hold-color buttons for

immediate color access

fader access to 40 predefined

mixed colors

TFX-32CON



fade time control

12 different chase patterns to

choose from



chase speed control

master dimmer level

blackout button

full on button

sound button

The TFX-32F provides the following features:



Selectable modes:

1. Blackout

2. Color Hold

3. Chase

TFX-32F

Mode

Up and down pedal buttons select

colors and chase patterns

Please refer to the TFX-32CON and TFX-32F user manuals for more in depth information.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

APPENDIX

DMX Primer

There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A

fixture capable of receiving DMX 512 will require one or a number of sequential channels. The user

must assign a starting address on the fixture that indicates the first channel reserved in the controller.

There are many different types of DMX controllable fixtures and they all may vary in the total number

of channels required. Choosing a start address should be planned in advance. Channels should

never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is

set incorrectly. You can however, control multiple fixtures of the same type using the same starting

address as long as the intended result is that of unison movement or operation. In other words, the

fixtures will be slaved together and all respond exactly the same.

DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is

where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which

the fixtures are connected is not important and has no effect on how a controller communicates to

each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures

using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The

shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET

carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)

FIXTURE LINKING

Figure 1 - DMX connector configuration

Resistance 120

ohm 1/4w between

pin 2 (DMX -) and

pin 3 (DMX +) of

the last fixture.

COMMON

DMX +

INPUT

OUTPUT

Termination reduces signal errors

and to avoid signal transmission

problems and interference, it is

DMX -

Note!

If you use a controller with a 5 pin DMX output connector, you will need to use a 5

pin to 3 pin adapter. Chauvet Model No: DMX5M.

The chart below details a proper cable conversion:

3 Pin to 5 Pin Conversion Chart

Conductor

3 Pin Female (output)

5 Pin Male (Input)

Pin 1

Ground/Shield

Data ( - )signal

Data ( + ) signal

Do not use

Pin 1

Pin 2

Pin 3

Pin 2

Pin 3

Do not use

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

DMX Channel Values

RGB&D Mode (RGB and Dimmer)

Channel

Value

Function

Notes

Red

000  255

Intensity: 0% ~ 100%

Green

Intensity: 0% ~ 100%

Blue

Intensity: 0% ~ 100%

Dimmer

0  100%

C&B Mode (Color and Brightness)

Channel

Value

Function

Notes

Spectrum Color Mix

See Color Mix Table

Dimmer

Intensity: 0% ~ 100%

See Color Mix table on the next

page

000  255

RGB and Chase Mode

Mode

Ch 1 (Mode) Ch 2

Ch 3

Ch 4

RGB Mode

000  029

030  094

Red: 0 ~ 100% Green: 0 ~ 100% Blue: 0 ~ 100%

Speed

8 Built-in Programs (Auto)

8 Built-in Programs (Sound) 094  159

Chase (Auto)

160  184

185  209

210  234

235  255

Dimming:

0 ~ 100%

Speed

Fade Time

Chase (Sound)

40 Color Chase (Auto)

40 Color Chase (Sound)

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

Color Mix Table (Preset)

DMX Value

Red Intensity

0% ~ 100%

Green Intensity

0% ~ 100%

Blue Intensity

0% ~ 100%

Notes

Blackout

100

Red @ Full only

100

Red @ Full

Proportional Green

100

Red & Green @ Full

100

Green @ Full

Proportional Red

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

100

Green @ Full

Proportional Red

100

Green @ Full only

100

Green @ Full

Proportional Blue

101

100

Green & Blue @ Full

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

100

Blue @ Full

Proportional Green

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

119

120

121

122

123

124

125

126

127

128

129

130

131

132

100

Blue @ Full

Proportional Green

133

134

135

136

100

Blue @ Full only

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

100

Blue @ Full

Proportional Red

168

100

Red & Blue @ Full

169

170

171

172

173

174

175

176

177

178

179

180

100

Red @ Full

Proportional Blue

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

100

Red @ Full

Proportional Blue

200

201

202

203

204

205

206

100

Red @ Full

Proportional Green and Blue

207

100

Red & Blue @ Full, Green @

50%

208

209

210

100

Blue @ Full

Proportional Red and Green

211

100

Green & Blue @ Full, Red @

50%

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

100

Green @ Full

Proportional Red and Blue

229

100

Red and Green @ Full, Blue @

50%

230

231

232

100

Red @ Full

Proportional Green and Blue

233

100

Red and Blue @ Full, Green @

50%

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

100

Blue @ Full

Proportional Red and Green

252

253

254

100

Blue and Green @ Full

Proportional Red

255

100

Red,Green,Blue @ FULL

(White)

Maintenance

To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage

and environment are contributing factors in determining frequency. As a general rule, fixtures should

be cleaned at least twice a month. Dust build up reduces light output performance and can cause

overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off

fixture before conducting maintenance.

Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust

collected on external vents and internal components. Clean all glass when the fixture is cold with a

mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply

solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical

surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil

and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or

becomes dirty, clean the lamps with an alcohol wipe.

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to

optimize light output. Cleaning frequency depends on the environment in which the fixture operates:

damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s

optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean

the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

Returns Procedure

Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.

Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products

returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the

fixture. Be prepared to provide the model number, serial number and a brief description of the cause

for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate

packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to

repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe

method to use.

Claims

Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be

reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and

submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim

for items such as missing component/part, damage not related to shipping, and concealed damage,

must be made within seven (7) days of receiving merchandise.

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

General Troubleshooting

Applies to

Foggers

& Snow

Dimmers&

Chaser

Symptom

Solution(s)

Lights

Controllers

Auto shut off

Check fan thermal switch reset



Beam is very dim or

not bright

Clean optical system or replace lamp

Check 220/110v switch for proper setting



Breaker/Fuse keeps

blowing

Check total load placed on device



Chase is too slow

Check users manual for speed adjustment



Device has no power

Check for power on Mains.

Check device’s fuse. (internal and/or external)

Fixture is not

responding

Check DMX Dip switch settings for correct

addressing

Check DMX cables



Check polarity switch settings

Fixture is on but there

is no movement to the

audio

Make sure you have the correct audio mode on the

control switches. If audio provided via ¼” jack, make

sure a live audio signal exists



Adjust sound sensitivity knob

Lamps cuts off

sporadically

Possible bad lamp or fixture is overheating.

Lamp may be at end of its life.



Light will not come on

after power failure

Some discharge lamps require a cooling off period

before the electronics in the fixture can kick start it

again, wait 5 to 10 minutes before powering up

Loss of signal

Use only DMX cables

Install terminator

Note: Keep DMX cables separated from power

cables or black lights.



Moves slow

No flash

Check 220/110v switch for proper setting



Re-install bulb, may have shifted in shipping

No laser output

Bounce mirror motor may have shifted during

shipping, readjust



No light output

Check slip ring & brushes for contact

Install bulb

Call service technician

Relay will not work

Check reset switch

Check cable connections



Remote does not work Make sure connector is firmly connected to device



Stand alone mode

All Chauvet lighting fixtures featuring stand-alone

functions do not require additional settings, simply

power the fixture and it will automatically enter into

this mode

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Appendix

Technical Specifications

WEIGHT & DIMENSIONS

Length...........................................................................................................................305 mm (12 in)

Width...............................................................................................................................229 mm (9 in)

Height .............................................................................................................................152 mm (6 in)

Weight.........................................................................................................................5.9 Kg (13.2 lbs)

POWER

Switch-selectable power settings.................................................................115V 60 Hz or 230V 50 Hz

European version............................................................................................................... 240V 50 Hz

AC input.......................................................................................................... 3-prong IEC 60320 C14

LAMPS

3 x EHM (115V)............................................................................................................ 2,000 hr, 300W

3 x EHM2 (230V) ......................................................................................................... 2,000 hr, 300W

THERMAL

Maximum ambient temperature......................................................................................... 40° (104° F)

FUSE

Main................................................................................................. 30mm Glass 10A 125V Fast Blow

PCB ............................................................................................................ 20mm Glass 2A Fast Blow

CONTROL & PROGRAMMING

Data input ............................................................................................. locking 3-pin XLR male socket

Data output ........................................................................................ locking 3-pin XLR female socket

Data pin configuration ............................................................................pin 1 shield, pin 2 (-), pin 3 (+)

Protocols.....................................................................................................................DMX-512 USITT

DMX Channels.............................................................................................................................2 to 4

ORDERING INFORMATION

Stage Wash™ 950............................................................................................................ TFX-950CM

Stage Wash™ Controller Pack......................................................................................... TFX-CONPK

CA-32F Colormix foot Controller............................................................................................TFX-SWF

Fuse 2A ........................................................................................................................ P170FUSE002

Fuse 10A ...................................................................................................................... P170FUSE010

TFX-950CM User Manual

Revision: 2006-01-20/16:37

Belshaw Brothers Oven BARO 2E User Manual
Black Decker Pressure Washer 598667 00 User Manual
Brother All in One Printer DCP J725DW User Manual
Brother Fax Machine FAX2580C 2480C User Manual
Bryan Boilers Boiler CFS 15 20 20D User Manual
Califone Music Pedal KMFT User Manual
Campbell Hausfeld Air Cleaner PA208503 User Manual
Chamberlain Home Security System CWV1000 User Manual
Christie Digital Systems Projector XENON CONSOLE User Manual
Cisco Systems IP Phone OL 11524 01 User Manual