Chicago Electric Chainsaw 2810 User Manual

16” ELECTRIC Chain Saw  
WITH BRAKE  
Model 02810  
ASSEMBLY AND OPERATING INSTRUCTIONS  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Visit ourWeb site at:http://www.harborfreight.com  
©
®
Copyright 2002 by Harbor Freight Tools . All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools.  
For technical questions, please call 1-800-444-3353.  
 
6.  
7.  
DRESS SAFELY. Do not wear loose clothing or jewelry, as they can become  
caught in moving parts. Wear a protective hair covering to prevent long hair from  
becoming caught in moving parts. Wear close fitting clothing and steel toed  
shoes.  
DO NOT OVERREACH. Keep proper footing and balance at all times to prevent  
tripping, falling, back injury, etcetera.  
8.  
9.  
INDUSTRIAL APPLICATIONS MUST FOLLOW OSHA REQUIREMENTS.  
STAY ALERT. Watch what you are doing at all times. Use common sense. Do  
not use this product when you are tired or distracted from the job at hand.  
10.  
11.  
CHECK FOR DAMAGED PARTS. Before using this product, carefully check that  
it will operate properly and perform its intended function. Check for damaged  
parts and any other conditions that may affect the operation of this product. Re-  
place or repair damaged or worn parts immediately.  
REPLACEMENT PARTS AND ACCESSORIES: When servicing, use only  
identical replacement parts. Only use accessories intended for use with this  
product. Approved accessories are available from Harbor Freight Tools.  
12.  
13.  
14.  
MAINTAIN THIS PRODUCT WITH CARE. Keep this product clean and dry for  
better and safer performance.  
MAINTENANCE: For your safety, service and maintenance should be performed  
regularly by a qualified technician.  
USETHE RIGHTTOOL FORTHE JOB. Do not attempt to force a small tool or  
attachment to do the work of a larger industrial tool. There are certain applica-  
tions for which this tool was designed. It will do the job better and more safely at  
the rate for which it was intended. Do not modify this tool, and do not use this tool  
for a purpose for which it was not intended.  
15.  
16.  
WARNING: The warnings, precautions, and instructions discussed in this manual  
cannot cover all possible conditions and situations that may occur. The operator  
must understand that common sense and caution are factors, which cannot be  
built into this product, but must be supplied by the operator.  
WARNING: Take caution as some woods contain preservatives such as copper  
chromium arsenate (CCA) which can be toxic. When cutting these materials extra  
care should be taken to avoid inhalation and minimize skin contact.  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
SPECIFIC PRODUCT WARNINGS AND PRECAUTIONS  
1.  
MAINTAIN A SAFE WORKING ENVIRONMENT. Make sure the work area is well  
lit. Make sure there is adequate surrounding workspace. Always keep the work  
area free of obstructions, tree limbs, vegetation, and other debris. Do not use the  
Chain Saw in areas near flammable chemicals, dusts, and vapors. Do not use the  
Chain Saw in a damp or wet location.  
2.  
3.  
DO NOT USE THE CHAIN SAW WITH ADULTS, CHILDREN, AND PETS IN  
CLOSE PROXIMITY.  
ALWAYS HOLD THE CHAIN SAW FIRMLY WITH BOTH HANDS UNTIL THE  
ROTATING CHAIN (57) COMPLETELY STOPS. MAKE SURE TO STAND IN A  
STABLE, BALANCED POSITION WHEN USING THE CHAIN SAW. Avoid awk-  
ward postures.  
4.  
5.  
DO NOT USE THE CHAIN SAW IF THE CHAIN (57) IS DULL.  
BE AWARE OFTHE DIRECTION OFTHE ROTATION OFTHE CHAIN (57). Chain  
must move in the direction shown in Figure C, page 7.  
6.  
ALWAYS BE PREPARED FOR THE POSSIBILITY OF CHAIN SAW KICKBACK.  
Kickback is a sharp, quick, upward movement of the Chain Saw when it is running.  
This usually occurs when the upper/front quarter of the Guide Bar (52) binds with  
the piece of wood being cut. In the event of a significant kickback, the Chain Safety  
Brake may be automatically triggered, instantly stopping the rotating Chain (57)  
and turning off the Chain Saw. The rotating chain may also be stopped by manually  
pushing the Chain Safety Brake forward.  
7.  
ALWAYS CARRY THE CHAIN SAW BY ITS HANDLE (47) WITH THE CHAIN  
(57) POINTING BACKWARDS ANDTHE CHAIN SAW A SAFE DISTANCE FROM  
YOUR BODY. NEVER CARRYTHE CHAIN SAW BY ITS ELECTRIC CORD (23).  
KEEP HANDS AND FINGERSWELL AWAY FROMTHE ON/OFFTRIGGER (25B)  
WHILE CARRYING THE CHAIN SAW.  
8.  
9.  
MAKE SURE THE WOOD BEING CUT DOES NOT CONTAIN FOREIGN BOD-  
IES SUCH AS NAILS, SPIKES, STONES, ETC. DO NOT ATTEMPTTO CUT ANY  
OTHER MATERIALS OTHER THAN WOOD.  
DO NOT ABUSETHE ELECTRIC CORD. Do not use the Electric Cord (23) to pull  
its Plug from a power outlet or extension cord. Keep the Electric Cord away from  
heat, water, oil, sharp edges, and moving parts. Do not route the Electric Cord  
where it can be walked on or tripped over.  
10.  
KEEP ALL SAFETY GUARDS IN PLACE, IN PROPER ADJUSTMENT, AND IN  
PROPER ALIGNMENT.  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
11.  
IF AN EXTENSION CORD (not included) IS USED, MAKE SURETO USE ONLY  
UL APPROVED, OUTDOOR, CORDS HAVING THE CORRECT GAUGE AND  
LENGTH. (See Figure A.)  
REQUIRED MINIMUM EXTENSION CORD GAUGE – 120 VOLT  
NAMEPLATE  
AMPERES  
EXTENSION CORD LENGTH  
(At Full Load)  
0 - 25  
Feet  
16  
16  
14  
25 - 50  
Feet  
50 -100  
Feet  
16  
100 – 150  
150– 200  
Feet  
Feet  
12  
-
0 - 5  
5.1 - 8  
8.1 - 12  
12.1 - 15  
15.1 - 20  
16  
16  
14  
12  
12  
10  
-
-
-
14  
12  
10  
10  
-
-
-
12  
10  
10  
FIGURE A  
12.  
REDUCE THE RISK OF ACCIDENTAL STARTING. Make sure the On/Off Trigger  
(25b) is in the “OFF” position before plugging the Electric Cord into a grounded, 120  
Volt, electrical outlet.  
13.  
14.  
15.  
NEVER pass hands or legs directly under the Chain (57) when cutting wood. Al-  
ways keep hands and legs a safe distance away from the rotating Chain.  
PRIOR TO STARTING THE CHAIN SAW, MAKE SURE ALL ADJUSTING KEYS  
AND WRENCHES ARE REMOVED FROM THE TOOL.  
ALLOW THE CHAIN (57) TO ROTATE UP TO FULL SPEED BEFORE FEEDING  
IT INTO WOOD. When turning off the Chain Saw, allow the Chain to slow and stop  
on its own. Do not press against the Chain to stop it.  
16.  
17.  
FEEDTHE CHAIN (57) GRADUALLY INTOTHE MATERIAL BEING CUT. Do not  
force the Chain Saw to remove material faster than it was designed to cut.  
NEVER ATTEMPT TO REMOVE MATERIAL STUCK IN THE MOVING PARTS  
OF THE CHAIN SAW WHILE IT IS PLUGGED IN AND RUNNING. TURN OFF  
THE CHAIN SAW IF THE CHAIN (57) NEEDS TO BE BACKED OUT OF AN UN-  
COMPLETED CUT.  
18.  
19.  
NEVER LEAVE THE CHAIN SAW UNATTENDED WHEN IT IS PLUGGED IN.  
Turn off the Chain Saw, unplug it from its electrical power source, and wait until it  
has completely stopped before leaving.  
ALWAYS RELEASETHE ON/OFFTRIGGER (25B)TO ITSOFFPOSITION, AND  
UNPLUG THE CHAIN SAW FROM ITS ELECTRICAL SUPPLY SOURCE BE-  
FORE PERFORMING ANY INSPECTION, MAINTENANCE, OR CLEANING  
PROCEDURES.  
20.  
IMPORTANT! TREE FELLING AND BRANCH TRIMMING IS A DANGEROUS  
ACTIVITY. USE OF A CHAIN SAW REQUIRESTHATYOU BE IN GOOD PHYSI-  
CAL CONDITION, WITH GOOD BALANCE AND COORDINATION. If you are in  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
any doubt about the safety issues involved, have a qualified, certified, arborist/tree  
surgeon do the work for you.  
21.  
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and  
other construction activities, contain chemicals known (to the State of California) to  
cause cancer, birth defects or other reproductive harm. Some examples of these  
chemicals are: lead from lead-based paints, crystalline silica from bricks and ce-  
ment or other masonry products, arsenic and chromium from chemically treated  
lumber. Your risk from these exposures varies, depending on how often you do this  
type of work. To reduce your exposure to these chemicals: work in a well ventilated  
area, and work with approved safety equipment, such as those dust masks that are  
specially designed to filter out microscopic particles. (California Health & Safety  
Code § 25249.5, et seq.)  
22.  
WARNING: We recommend that people with pacemakers not use this tool. This  
tool produces strong electromagnetic fields that can cause interference or failure of  
the pacemaker. People with pacemakers should consult their physician(s) for ad-  
vice.  
UNPACKING  
When unpacking, check to make sure all the parts shown on the Parts List on page 11  
are included. If any parts are missing or broken, please call Harbor Freight Tools at the  
number shown on the cover of this manual as soon as possible.  
ASSEMBLY INSTRUCTIONS  
NOTE: For additional references to the parts listed in the following pages, refer to the  
Assembly Diagram on page 12.  
To Attach Or ReplaceThe Chain Guide Rail And Chain:  
1.  
2.  
WARNING: Make sure to turn the On/Off Trigger (25b) to its “OFF” position and un-  
plug the Electric Cord (23) from its electrical outlet before performing this procedure.  
Remove Screw (7) and Nylon Insert Nut (67) from the Chain Cover (46) with the  
tools provided. Note the Blade Guide Pin (62) and Bolt (6) shown in Figure B. Make  
sure the Guide Pin is positioned near the rear (left end) of the slot. Make certain that  
the oil port is open and free of debris.  
3.  
4.  
Place the Chain (57) around the rear of the Chain Gear (45), making certain that the  
teeth along the top of the Chain point forward.  
Place Guide Bar (52) with the center slot over the threaded end of the Bolt (66), and  
fixed pin (molded into the Front Cover (42)), as in Figure C. The Blade Guide Pin  
(62) goes into the lower hole in the blade. These steps may be easier with assis-  
tance.  
REV 05/05  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 6  
 
FIGURE B  
5.  
6.  
Replace the Chain Cover (46), and tighten the Nylon Insert Nut (67) so that the  
Cover is snug, but not tight. (See Figure D, next page.)  
Pull gently up on the tip of the Guide Bar (52), while turning the Blade Adjustment  
Screw (61) clockwise (photo 005.) Because the saw is light in weight, this is easier  
if someone holds the handle. Do not overtighten the Chain. There should only be  
1
about / ” of space when the Chain is pulled upward at the center of the Guide Bar.  
4
Lightly oil the entire Chain (57). (See Figure C.)  
FIGURE C  
7.  
When finished, tighten the Nylon Insert Nut (67) securely, and replace Screw (7).  
Check the Chain tension after initial operation of the saw. It may need adjustment.  
REV 05/05  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 7  
 
BLADE ADJUSTMENT  
SCREW (61)  
OIL FILL CAP (11)  
ON/OFFTRIGGER (25b)  
CHAIN (57)  
NUT  
(67)  
GUIDE BAR (52)  
CHAIN COVER  
(46)  
FIGURE D  
To Check For Proper Chain Tension:  
1.  
The Chain (57) tension is proper when the Chain snaps back after being pulled 1/4”  
away from the Guide Bar (52) with light force. There should be no sagging between  
the Chain and Guide Bar underneath. When necessary, use a screwdriver to turn  
the Adjustment Screw (61) clockwise to tighten, or counterclockwise to loosen, the  
Chain (57). (See Figure D.)  
2.  
NOTE: A Chain (57) which is too taut leads to premature Chain and Guide Bar (52)  
wear. A Chain which is too loose may jump out of the Guide Bar groove and dam-  
age the tool or cause personal injury. New chains typically lose tension initially  
during use. When necessary, readjust the Chain tension by following the directions  
in Step # 1 of this section.  
To RefillThe Automatic Chain Lubrication System:  
1.  
The Chain Saw features an automatic Chain Lubrication System with a built-in Oil  
Reservoir. Lubrication of the Chain (57) is carried out automatically while the Chain  
Saw is running. The oil level should be checked before each use of the Chain Saw.  
2.  
To refill the Oil Reservoir, unscrew the Oil Fill Cap (11). Fill the Oil Reservoir with a  
quality grade chain saw Chain Oil (SAE 30). When filling, avoid introducing dirt or  
other foreign material into the Oil Reservoir. Then, retighten the Oil Fill Cap onto the  
Oil Reservoir. (See Figure D.)  
REV 05/05  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 8  
 
OPERATING INSTRUCTIONS  
The Safety Brake:  
1.  
The Safety Brake is activated when the back of the operator’s hand pushes against  
the back of the Protect Plate (17). When activated, the Chain Saw will stop auto-  
matically, and the On/Off Trigger (25b) should be manually released. Next, pull the  
Protect Plate (17) back to its initial position in order to restart the Chain Saw.  
NOTE: If the Protect Plate (17) is not pulled back to its initial position, the Chain Saw will  
not operate. (See Figure E.)  
2.  
To check for proper operation of the Safety Brake, disconnect the Chain Saw from  
its electrical power outlet and push the Protect Plate (17) forward. Pull on the Chain  
(57) with your hand protected by heavy work gloves. The Chain Saw should be  
automatically locked in its “OFF” mode.  
ON/OFFTRIGGER (25b)  
PROTECT PLATE (17)  
CHAIN (57)  
HANDLE (47)  
ELECTRIC  
CORD (23)  
CARBON BRUSH (4)  
CARBON BRUSH HOLDER (5)  
CARBON BRUSH HOUSING (6)  
FIGURE E  
To StartThe Chain Saw:  
1.  
2.  
Make sure the On/OffTrigger (25b) is in itsOFFposition. (See Figure E.)  
Plug the Electric Cord (23) into a grounded, 120 volt, electrical outlet.  
(See Figure E.)  
3.  
4.  
5.  
6.  
7.  
Use both hands to firmly grasp the handle portion of the Motor Housing Handle (1)  
and Handle (47). (See Figure E.)  
Before starting the Chain Saw, make sure nothing is in contact with the Chain (57).  
(See Figure E.)  
Make sure the Protect Plate (17) is pulled back towards your body until it “clicks”  
and locks in place. (See Figure E.)  
To start the Chain Saw, push the Safety Switch on the On/Off Trigger (25b) and  
squeeze the On/Off Trigger. (See Figure E.)  
Release the On/OffTrigger (25b) to stop the Chain Saw. WARNING: Firmly hold the  
Chain Saw with both hands until the Chain Saw completely stops. (See Figure E.)  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 9  
 
INSPECTION, MAINTENANCE, AND CLEANING  
1.  
2.  
WARNING: Always turn the On/OffTrigger (25b) to its “OFF” position and unplug the  
Electric Cord (23) from its electrical outlet before performing any inspection, mainte-  
nance, or cleaning. (See Figure E.)  
BEFORE EACH USE, inspect the general condition of the Chain Saw. Check for  
loose screws, misalignment or binding of moving parts, cracked or broken parts  
(i.e., Chain, 57), damaged electrical wiring, and any other condition that may affect  
its safe operation. If abnormal noise or vibration occurs, have the problem corrected  
before further use. Do not use damaged equipment.  
3.  
4.  
UPON EVERY THREE HOURS OF USE, make sure the Chain (57) is adequately  
lubricated and taut. If necessary, remove the Guide Bar (52) and Chain. Clean the  
groove in the Guide Bar thoroughly and clean the Oil Port in the Front Cover (42) to  
ensure that it is not blocked or obstructed, see Figure B. To maximize the life of the  
Guide Bar, turn the Guide Bar over and then reinstall. (See Figures C and D.)  
PERIODICALLY, remove the Carbon Brush Housing (6) to inspect the condition of  
the Carbon Brush (4). If the Carbon Brush is simply dirty, you may carefully clean it  
with a pencil eraser. The Carbon Brush has a wear limit marking on it. You may  
safely use the Carbon Brush up to the wear limit. When it has worn up to the wear  
limit, the Carbon Brush must be replaced. When replacing the Carbon Brush make  
sure it fits neatly into its Carbon Brush Holder (5) and that the spring on the Carbon  
Brush operates freely. Make sure the carbon portion of the Carbon Brush contacts  
the Motor Armature (24). After inspection or replacement, replace the Carbon Brush  
Housing. (See Figure E.)  
5.  
6.  
TO CLEAN: Clean with a soft brush, cloth, or vacuum to remove debris from the  
Cold Saw. If necessary, use a mild detergent or mild solvent. Then, use a premium  
quality, lightweight machine oil to lubricate all moving parts.  
If cutting efficiency diminshes, the included round file may be used to sharpen the  
teeth of the chain. The chain should also be sharpened professionally at least once  
a year, depending on use.  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS MANUAL AS A  
REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTA-  
TION ORWARRANTY OF ANY KINDTOTHE BUYERTHAT HE OR SHE IS QUALIFIEDTO MAKE ANY REPAIRSTO  
THE PRODUCT ORTHAT HE OR SHE IS QUALIFIEDTO REPLACE ANY PARTS OFTHE PRODUCT. IN FACT,THE  
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACE-  
MENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSEDTECHNICIANS AND NOT BYTHE BUYER.  
THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRSTOTHE ORIGINAL  
PRODUCT OR REPLACEMENT PARTSTHERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF RE-  
PLACEMENT PARTSTHERETO.  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 10  
 
PARTS LIST  
Part  
1
Description  
Motor housing  
Rear cover  
Q'ty  
1
Part  
Description  
Q'ty  
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
2
1
1
1
1
1
32 Brake plate  
33 Brake block  
34 Brake belt  
2
1
3a Screw ST4.2*18  
3b Flat washer  
10  
11  
1
35 Pinion gear  
36 Connection rod  
37 Terminal  
4
5
6
7
8
9
Carbon brush  
Carbon brush holder  
Carbon brush housing  
Screw ST5*20  
1
1
38 Torsion spring  
39 Switch  
5
Screw ST3*16  
4
40 Bearing 608  
41 Big gear  
Screw ST5*30  
2
10 Stator  
1
42 Front cover  
43 Screw M6*35  
44 Nut M6  
11 Oil bottle  
1
13 Oil pipe  
1
14a Oil pump 1  
14b Steel ball dia.3.5  
14c Oil pump spring  
14d Oil pump pressure plate  
14e Oil pump pull rod  
14f Oil pump 2  
15 Screw M4*10  
16 Stop spring  
17 Protect plate  
18 Pin 5*25  
1
45 Chain gear  
46 Chain cover  
47 Side handle  
49 Screw ST5*35  
50 Screw ST5*22  
51 Housing  
1
1
1
1
1
2
52 Guide bar  
1
54 Bearing 609  
55 Bearing  
1
1
56 Screw ST5*22  
57 Chain  
19 Winding Cover  
20 Bearing 608  
21 Brake anchor pin  
22 Brake lock  
1
1
58 Pin 4*7  
1
59 Rubber terminal  
60 Screw ST4*16  
61 Blade adjustment screw M5*30  
62 Blade guide pin  
63 Spring washer  
64 Flat washer  
65 Nut M10  
1
23 Electric cord  
24 Armature  
1
1
25a Trigger stop rod  
25b Trigger  
1
1
25c Trigger spring  
27 Cord guard  
28 Capacitor  
1
1
66 Hex bolt M8*25  
67 Nylon insert nut M8  
68 Side cover  
1
29 Screw ST4.2*14  
30 Cord anchorage  
3
1
69 Retaining Ring  
REV 05/05  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 11  
 
ASSEMBLY DIAGRAM  
NOTE
REV 05/05  
SKU 02810  
For technical questions, please call 1-800-444-3353.  
Page 12  
 

Bertazzoni Range H304GGVCR User Manual
Black Decker Cordless Drill 1901 User Manual
Black Decker Iron F975 User Manual
Blanco Indoor Furnishings 157 060 User Manual
Bose Radio 343207 1110 User Manual
Braun Electric Shaver Pulsonic User Manual
Brother Fax Machine MFC6490CW User Manual
Campbell Hausfeld Nail Gun IN715703AV User Manual
Carrier Refrigerator 30MPA User Manual
CFM Fan TEK225H H2 User Manual