3/8” CLOSE QUARTER DRILL
Model 92956
OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
2.
3.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite flammables.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
ELECTRICAL SAFETY
4.
Grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
5.
6.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation
eliminates the need for the
three wire grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
7.
8.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use the Power Cord to carry the tools
or pull the Plug from an outlet. Keep the Power Cord away from heat, oil,
sharp edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
9.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 3
PERSONAL SAFETY
10.
Stay alert. Watch what you are doing, and use common sense when
operating a power tool. Do not use a power tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
11.
12.
13.
14.
15.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
TOOL USE AND CARE
16.
Use clamps (not included) or other practical ways to secure and support
the workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
17.
18.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
19.
20.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 4
21.
22.
Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with a sharp cutting edge are less likely to bind and are easier
to control. Do not use a damaged tool. Tag damaged tools “Do not use” until
repaired.
Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tool’s operation. If damaged,
have the tool serviced before using. Many accidents are caused by poorly
maintained tools.
23.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SERVICE
24.
25.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
1.
Hold tool by insulated gripping surfaces when performing an operation
where the cutting tools may contact hidden wiring or its own cord. Contact
with a ‘live’ wire will make exposed metal parts of the tool ‘live’ and shock the
operator.
2.
3.
Always wear ANSI approved safety impact eye goggles and full face shield
when operating this product.
Maintain labels and nameplates on the Drill. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
4.
5.
Do not reach under or behind the material being drilled.
Make sure the workpiece is free from nails and any other foreign objects
which can damage a drill bit.
6.
7.
Maintain a firm grip with both hands on the Drill, and position your body
and arm to allow you to resist torque forces.
Do not use a dull or damaged drill bits. Unsharpened or damaged drill bits
cause excessive friction and binding.
8.
Use caution when drilling into existing walls or other blind areas. Check for
unexposed electrical wires and cables in the drilling path before drilling.
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 5
9.
Industrial applications must follow OSHA requirements.
10.
Use the right tool or attachment for the right job. Do not attempt to force a
small tool or attachment to do the work of a larger industrial tool or attachment.
There are certain applications for which this product was designed. It will do the
job better and more safely at the rate for which it was intended. Do not modify
this product, and do not use this product for a purpose for which it was not
intended.
11.
Always turn off the Drill and unplug the Power Cord/Plug (31) from its
electrical outlet before changing accessories or performing inspection,
maintenance, or cleaning procedures.
12.
13.
WARNING! People with pacemakers should consult their physician(s)
before using this product. Operation of electrical equipment in close proximity to
a heart pacemaker could cause interference or failure of the pacemaker.
WARNING! Some dust created by power sanding, sawing, grinding, drilling,
and other construction activities, contain chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:lead from lead-based paints, crystalline silica from bricks and cement
or other masonry products, arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this type of
work. To reduce your exposure to these chemicals: work in a well ventilated area,
and work with approved safety equipment, such as those dust masks that are
specially designed to filter out microscopic particles. (California Health & Safety
Code 25249.5, et seq.)
14.
WARNING! The warnings, precautions, and instructions discussed in this
manual cannot cover all possible conditions and situations that may occur. The
operator must understand that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
GROUNDING
WARNING!
Improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded. Do not modify the power cord plug provided with the tool. Never
remove the grounding prong from the plug. Do not use the tool if the power cord or
plug is damaged. If damaged, have it repaired by a service facility before use. If the
plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 6
GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS
1.
Tools and equipment marked with “Grounding Required” have a three wire cord
and three prong grounding plug. The plug must be connected to a properly
grounded outlet. If the tool or equipment should electrically malfunction or break
down, grounding provides a low resistance path to carry electricity away from the
user, reducing the risk of electric shock. (See Figure A.)
2.
3.
The grounding prong in the plug is connected through the green wire inside the
cord to the grounding system in the tool. The green wire in the cord must be the
only wire connected to the tool’s grounding system and must never be attached
to an electrically “live” terminal. (See Figure A.)
Your tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like that in the following illustration. (See Figure A.)
FIGURE A
DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS
1.
2.
Tools marked “Double Insulated” do not require grounding. They have a special
double insulation system which satisfies OSHA requirements and complies with
the applicable standards of Underwriters Laboratories, Inc., the Canadian
Standard Association, and the National Electrical Code. (See Figure B.)
Double insulated tools may be used in either of the 120 volt outlets shown in the
following illustration. (See Figure B.)
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 7
FIGURE B
EXTENSION CORDS
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools
can use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Figure C, next page.)
3.
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 16 gauge cord.
(See Figure C.)
4.
5.
When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required.
(See Figure C.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Figure C.)
6.
7.
If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure your extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
8.
Protect your extension cords from sharp objects, excessive heat, and damp or
wet areas.
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 8
RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*
(120 VOLT)
NAMEPLATE
EXTENSION CORD LENGTH
AMPERES
(At Full Load)
25
FEET
18
18
18
18
18
14
12
50
FEET
18
18
18
16
14
12
10
75
FEET
18
18
16
14
12
10
-
100
FEET
18
16
14
12
10
-
150
FEET
0-2.0
2.1-3.4
3.5-5.0
16
14
12
12
-
5.1-7.0
7.1-12.0
12.1-16.0
16.1-20.0
-
-
-
*Based on limiting the line voltage drop
to five volts at 150% of the rated amperes.
FIGURE C
SYMBOLOGY
Double Insulated
Underwriters
Laboratories, Inc.
Canadian Standards
Association
Volts Alternating
V ~
Current
Amperes
A
no
No Load Revolutions
Per Minute (RPM)
xxxx/min.
FIGURE D
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 9
UNPACKING
When unpacking, check to make sure all accessories listed above are included, and that
the product is intact and undamaged
PRODUCT FEATURES
NOTE:
For additional information regarding the parts mentioned in
the following pages, refer to the Assembly Diagram on page 14.
1.
2.
Drill Chuck (3) and Chuck Key (33): The Close Quarter Drill is equipped with a
3/8” keyed Drill Chuck (3) that will accept drill bits (not included) with a 1/16” to
3/8” shank. Installing a drill bit into the Drill Chuck requires the use of the
accessory Chuck Key (33). Always make sure the drill bits are firmly secured in
the Drill Chuck prior to using the Drill. (See Figure D.)
Trigger (30) and Trigger Lock (34): The Trigger (30) is operated manually
simply by squeezing the Trigger to turn on the Drill and releasing pressure on the
Trigger to turn off the Drill. The Trigger features a Trigger Lock (34) for continuous
running of the Drill. To set the Drill in a continuous run mode, squeeze the
Trigger and depress the Trigger Lock. Then, release pressure on the Trigger.
The Drill will continue to run. To turn off the Drill, squeeze and let up on the
Trigger. (See Figure D.)
3.
Forward/Reverse Switch (35): The Forward/Reverse Switch (35) is located
directly above the Trigger (30). For clockwise rotation, move the Forward/
Reverse Switch to the right. For a counterclockwise rotation, move the
Forward/Reverse Switch to the left. Use the Forward/Reverse Switch only after
the Hammer Drill has come to a complete stop. (See Figure D.)
DRILL CHUCK (3)
FORWARD/REVERSE SWITCH (35)
TRIGGER (30)
TRIGGER LOCK (34)
TO LOOSEN
FIGURE D
CHUCK KEY
POWER CORD/PLUG
(31)
TO TIGHTEN
(33)
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 10
OPERATING INSTRUCTIONS
1.
Use caution when drilling into existing walls or other blind areas. Check for
unexposed electrical wires and cables in the drilling path before drilling.
2.
3.
4.
Use the Forward/Reverse Switch (35) to select the desired rotation of the tool.
(See Figure D.)
Insert a drill bit (not included) into the Drill Chuck (3), and secure the drill bit in
the Drill Chuck with the Chuck Key (33). (See Figure D.)
Make sure the Trigger (30) is in its “OFF” position. Then, plug the Power Cord/
Plug (31) into the nearest 120 volt, grounded, electrical outlet. (See Figure D.)
5.
6.
Before drilling, clamp the object down securely. A poorly secured piece of
material may result in personal injury and/or innacurate drilling.
Mark the center of the hole to be drilled with a center punch to prevent the drill bit
from “walking” when first beginning to drill.
7.
8.
9.
Hold the Drill firmly with both hands.
Position the drill bit on the material that is to be drilled.
To begin drilling, squeeze the Trigger (30). The speed at which the Drill Chuck
(3) rotates varies depending on how far in the Trigger is squeezed.
(See Figure D.)
10.
11.
If desired, activate the Trigger Lock (34) to set the Drill in a continuous run mode.
(See Figure D.)
Avoid overloading the Drill. Do not apply excessive pressure to the Drill while
drilling. If the speed of the tool drops abnormally, decrease the pressure
immediately. If the drill bit stops abruptly, or the drill bit becomes blocked, release
the Trigger (30) at once. (See Figure D.)
12.
13.
Drill only as deep as is necessary. Do not drill deeper than necessary into walls
or other areas where you cannot identify any possible hazards behind the drilling
surface.
To reduce jamming as the drill bit breaks through the workpiece, decrease the
drilling pressure when the point of the drill bit breaks through the workpiece.
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 11
14.
When you have drilled the hole, remove the drill bit from the hole while the Drill
Chuck (3) is still rotating. This prevents the drill bit from getting caught in the
hole and causing damage.
15.
16.
17.
Release pressure on the Trigger (30) to stop the Drill. (See Figure D.)
Unplug the Drill from its electrical outlet.
Remove the drill bit from the Drill Chuck (3). Then, store the Drill and its Chuck
Key (33) in a dry, safe, location out of reach of children and other unauthorized
users.
INSPECTION, MAINTENANCE, AND CLEANING
1.
2.
WARNING! Always make sure the Trigger (30) is in its “OFF” position, and
unplug the Power Cord/Plug (31) from its 120 volt electrical outlet before
performing any inspection, adjustments, maintenance, or cleaning.
Before each use, inspect the general condition of the Drill. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts,
damaged electrical wiring, loose, cracked, or bent drill bits, and any other
condition that may affect its safe operation. If abnormal noise or vibration occurs,
have the problem corrected before further use.
Do not use damaged equipment.
3.
4.
Daily: With a soft brush, cloth, or vacuum, remove all dust and debris from the
Drill. Then, use a premium quality, lightweight machine oil to lubricate
all external moving parts.
To replace the Carbon Brushes: It may become necessary at sometime to
replace the two Carbon Brushes (19) when the Motor performance decreases, or
stops working completely. The Carbon Brushes are located on each side of
the Motor Housing (4) and Motor Housing Cover (17). To do so, remove the
two Brush Holder Covers (18). Then, remove the two Carbon Brushes from the
Brush Holders (20). If the Carbon Brushes are worn down more than 1/2,
replace both Carbon Brushes. If, however, the Carbon Brushes are just dirty they
may be cleaned by rubbing them with a pencil eraser. When installing the
Carbon Brushes, make sure the carbon portion of the Carbon Brushes contact
the Motor Armature, and that the springs face away from the Motor. Also, make
sure the springs operate freely. After cleaning or replacement, replace the Brush
Holders. NOTE: New Carbon Brushes tend to arc or spark when first used
until they wear and conform to the Motor’s Armature. (See Figure E, next page.)
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 12
5.
CAUTION! All maintenance, service, or repairs not listed in this manual
are only to be attempted by a qualified service technician.
CARBON BRUSH (19)
CARBON BRUSH (19)
FIGURE E
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION
OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part #
Description
Screw (M5 x 20 Left)
Spring Washer (5)
Drill Chuck
Motor Housing
Gear Housing
Rubber Pin
Ball Bearing (6002)
Pin
Gear (Z4)
Qty.
Part #
Description
Carbon Brush
Brush Holder
Gear Spindle (Z1)
Ball Bearing (626)
Link Bushing
Ball Bearing (608)
Armature
Ball Bearing (607)
Field
Screw (M4 x 20)
Rubber Pin
Qty.
1
2
3
4
5
6
7
8
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
2
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
2
2
1
1
1
1
1
1
1
3
1
1
1
8
1
1
1
9
10
11
12
13
14
15
16
17
18
Spindle
Gear (Z5)
Gear Spindle (Z3)
Ball Bearing (626)
Gear (Z2)
Ball Bearing (625)
Gear Housing Cover
Motor Housing Cover
Brush Holder Cover
Trigger
Power Cord/Plug
Screw (ST4.2 x 14)
Chuck Key (not shown)
Trigger Lock
Forward/Reverse Switch
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 13
ASSEMBLY DIAGRAM
SKU 92956
For technical questions please call 1-800-444-3353
PAGE 14
|