IN STAL LA TIO N I NST RUCT IONS
Flat Panel Display Security Kit
(FSA-1009 and KSA-1009)
The flat panel display security kit replaces exposed
hardware with security hardware.
NOTE: In some installations (i.e. single arm mount) not
all fasteners included in this kit will be required.
The security accessory kit can be used on most flat
panel configurations.
The pivot/pitch mount and mounts that are equipped with
a swing arm use the 4-inch security pivot bolts. Mounts
that are equipped with a height-adjustable arm use the
5-inch security pivot bolts. Some configurations can use
both the 4-inch and 5-inch security pivot bolts.
Security Parts Kit
The security accessory kit is available for F-Series
mounts and K-Series mounts.
BEFORE YOU BEGIN
x
CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly
study all instructions and illustrations before you begin to install the mount brackets. Pay particular
attention to the “Important Warnings and Cautions” on Page 2.
x
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-894-6280.
CHIEF MANUFACTURING INC.
8807-000025 (Rev. C)
©2006 Chief Manufacturing
06/06
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PARKWAY, STE. 700
SAVAGE, MINNESOTA 55378 USA
Installation Instructions
FSA/KSA-1009
CONTENTS
TOOLS REQUIRED FOR
INSTALLATION
TOOLS REQUIRED FOR INSTALLATION .................3
PARTS.......................................................................3
DISPLAY SECURITY SCREWS.................................4
Flush Mount............................................................4
Recessed Mount.....................................................4
INSTALL SECURITY PIVOT BOLTS..........................5
Install 4-inch Security Pivot Bolts ............................5
Install 5-inch Security Pivot Bolts ............................5
Install 4-inch and 5-inch Security Pivot Bolts ...........5
INSTALL SECURITY SET SCREWS..........................6
Option I...................................................................6
Option II..................................................................6
x
x
x
1/8” Hex key wrench
5/32” Hex key wrench
3/16” Hex Key wrench
NOTE: Other tools may be required depending on the
method of installation.
PARTS
Prior to installing the security kit, unpack carton completely and verify the contents listed in Table 1. If you are missing
any of the parts, contact Customer Service at 1.800.582.6480.
Table 1. Security Parts Kit
ITEM
10
DESCRIPTION
Security Pivot Bolt, 4”
QTY ITEM
DESCRIPTION
M4 x 12mm Security Screw
M4 x 20mm Security Screw
1/8” Hex Key
QTY
3
2
1
1
1
60
70
80
90
4
4
1
1
1
20
Security Pivot Bolt, 5”
30
1/4-20 x 1/4” Security Screw
1/4-20 x 5/8” Set Screw
40
5/32” Security Hex Key
50
5/16-18 x 3/4” Security Set Screw
100 3/16” Security Hex Key
10
60
70
90
40
100
50
80
30
20
Figure 1. Security Kit Parts
3
Installation Instructions
FSA/KSA-1009
M4 x 12mm
Security Screw
(typical)
DISPLAY SECURITY SCREWS
Select the appropriate hardware from the security kit to
secure your display. Select the procedure, listed below,
that applies to your application.
Centris
Mount
x
Flush Mount (no spacers required)
Recessed Mount (spacers required)
x
Flush Mount
1. Verify that you have the correct parts.
2. Remove two M4 x 12mm screws from the top
mounting holes on the display.
3. Install two M4 x 12mm security screws (60) into the
top mounting holes on the display (see Figure 2).
Display
4. Repeat Steps 2 and 3 to install the two remaining
M4 x 12mm security screws (60) into the bottom
mounting holes on the display.
Figure 2. Flushed Mount
Recessed Mount
1. Verify that you have the correct parts.
NOTE: If your display uses a screw size other than
M4 x 20mm, DO NOT use the M4 x 20mm
security screws. Using the wrong screws could
result in damage to your display.
M4 x 20mm
Security Screw
(typical)
2. Remove two M4 x 20mm screws from the top
mounting holes on the display, exercising care to
retain the two spacers beneath the Centris mount.
Centris
Mount
3. Install two M4 x 20mm security screws (70) and two
spacers into the top mounting holes on the display
(see Figure 2).
Spacers
4. Repeat Steps 2 and 3 to install the two remaining
M4 x 20mm security screws (70) into the bottom
mounting holes on the display.
Display
Figure 3. Recessed Mount
4
Installation Instructions
FSA/KSA-1009
INSTALL SECURITY PIVOT BOLTS
Perform the applicable procedure to replace the regular
pivot bolts with security pivot bolts. You will need the
security hex keys (provided) to complete the installation.
4” Security Pivot Bolts
Centris
Mount
Small
Washer
Install 4-inch Security Pivot Bolts
For swing arm models, replace the standard pivot bolts
with security pivot bolts, as follows:
NOTE: Do not remove the display (not shown) from the
Pivot Pin
Flat
Washers
Centris mount.
1. Verify that you have the correct parts.
Large
Washer
2. Remove the 4-inch pivot bolt from the Centris mount.
Exercise care to retain the other parts shown in
Figure 4.
Nut
3. Install the 4-inch security pivot bolt (10) at the
Centris mount. Make sure the other parts are
installed in place as shown in Figure 4.
4. Repeat Steps 2 and 3 to install the second
4-inch security pivot bolt (10) into the other end of
the mount.
Install 5-inch Security Pivot Bolts
For lift arm models, replace the standard pivot bolts with
security pivot bolts, as follows:
Figure 4. Install 4-inch Security Pivot Bolt
(Swing Arm Example)
NOTE: Do not remove the display (not shown) from the
5” Security Pivot Bolts
Centris mount.
Centris
Mount
1. Verify that you have the correct parts.
2. Remove the 5-inch pivot bolt from the Centris mount.
Exercise care to retain the other parts shown in
Figure 5.
Small
Washer
3. Install the 5-inch security pivot bolt (20) at the
Centris mount. Make sure the other parts are
installed in place as shown in Figure 5.
Pivot Pin
Flat
Washers
Large
Washer
4. Repeat Steps 2 and 3 to install the second
5-inch security pivot bolt (20) into the other end of
the mount.
4” Security
Pivot Bolt
Nut
Install 4-inch and 5-inch Security Pivot Bolts
For models that have both 4-inch and 5-inch pivot bolts,
do the following:
NOTE: Do not remove the display (not shown) from the
Centris mount.
1. Verify that you have the correct parts.
2. Remove and replace the regular pivot bolt with the
applicable security pivot bolt (see Figure 5).
Figure 5. Install 5-inch Security Pivot Bolt
(Lift Arm Example)
5
Installation Instructions
FSA/KSA-1009
INSTALL SECURITY SET SCREWS
The security set screw is used to secure the pivot-pitch
wall mount. You will need the security hex keys
(provided) to install the security set screws.
There are two different wall plates, which require
different security requirements. Select the option that
applies to your configuration.
Option I
NOTE: If your wall plate uses a 1/4-20 set screw,
replace it with a 1/4-20 x 5/8” security set screw
(40) and a 1/4-20 x 1/4” security screw (30).
The existing set screw in the wall plate is too
long to be used with the 1/4-20 x 1/4” security
screw.
1/4-20 x .625
Set Screw
1. Verify that you have the correct parts.
2. Remove the existing 1/4-20 x 1/4” set screw from the
wall plate.
1/4-20 x .25
Security Screw
3. Install a 1/4-20 x 5/8” security set screw (40) and a
1/4-20 x 1/4” security screw (30) into the wall plate in
the order shown in Figure 6.
Figure 6. Install Security Set Screws (Option I)
Option II
1. Verify that you have the correct parts.
2. Remove the existing 5/16-18 x 3/4” set screw from
the wall plate.
3. Install the 5/16-18 x 3/4” security screw (50) in the
wall plate (see Figure 7).
5/16-18 x .75
Security
Set Screw
Figure 7. Install Security Set Screws (Option II)
6
|