Chief Manufacturing Indoor Furnishings MSM User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
Instrucciones de instalación  
Installationsanleitung  
Istruzioni di installazione  
Installatie-instructies  
Instruções de Instalação  
Instructions d´installation  
MTM  
MSM  
FUSION MEDIUM HEIGHT ADJUST  
FLAT PANEL MOUNTS  
MSM/MTM Series  
 
Installation Instructions  
MSM/MTM Series  
DIMENSIONS  
25.60  
[650]  
MSM  
MAX HORIZONTAL SPAC ING  
18.79  
477.4  
16.00  
406.4  
.50  
[12.7]  
UP/DOWN  
ADJUSTMENT  
EAC H SIDE  
.35  
8.9  
7.63  
193.7  
.32  
8.1  
1.52  
38.5  
7.53  
191.2  
16.50  
419.1  
15.75  
400  
1.00  
25.4  
13.53  
343.7  
6.00  
152.4  
15.10  
383.4  
MAX  
1.96  
49.8  
1.75  
44.5  
VERTIC AL  
SPAC ING  
.33  
RAILS SLIDE  
LEFT/RIG HT  
FOR STUD  
OFFSET  
8.3  
.50  
12.7  
1.00  
25.4  
25.00  
635  
MTM  
26.25  
[667]  
MAX HORIZONTAL SPAC ING  
18.79  
477.4  
.50  
[12.7]  
UP/DOWN  
ADJUSTMENT  
EAC H SIDE  
16.00  
406.4  
12°  
MAX TILT  
7.63  
193.7  
.32  
8.1  
.38  
9.5  
2.00  
50.8  
7.53  
191.2  
15.75  
[400]  
1.00  
25.4  
16.50  
419  
13.53  
343.7  
6.00  
152.4  
15.10  
383.4  
1.98  
50.3  
MAX  
VERTIC AL  
SPAC ING  
1.75  
44.5  
RAILS SLIDE  
LEFT/RIG HT  
FOR STUD  
OFFSET  
.33  
8.3  
.50  
12.7  
1.00  
25.4  
25.00  
635  
3
 
Installation Instructions  
MSM/MTM Series  
LEGEND  
Tighten Fastener  
Pencil Mark  
Apretar elemento de fijación  
Befestigungsteil festziehen  
Apertar fixador  
Marcar con lápiz  
Stiftmarkierung  
Marcar com lápis  
Segno a matita  
Serrare il fissaggio  
Bevestiging vastdraaien  
Serrez les fixations  
Potloodmerkteken  
Marquage au crayon  
Loosen Fastener  
Drill Hole  
Aflojar elemento de fijación  
Befestigungsteil lösen  
Desapertar fixador  
Perforar  
Bohrloch  
Fazer furo  
Praticare un foro  
Gat boren  
Allentare il fissaggio  
Bevestiging losdraaien  
Desserrez les fixations  
Percez un trou  
Phillips Screwdriver  
Adjust  
Destornillador Phillips  
Ajustar  
Kreuzschlitzschraubendreher  
Chave de fendas Phillips  
Cacciavite a stella  
Einstellen  
Ajustar  
Regolare  
Afstellen  
Ajuster  
Kruiskopschroevendraaier  
Tournevis à pointe cruciforme  
Open-Ended Wrench  
Llave de boca  
Remove  
Quitar  
Gabelschlüssel  
Chave de bocas  
Chiave a punte aperte  
Steeksleutel  
Entfernen  
Remover  
Rimuovere  
Verwijderen  
Retirez  
Clé à fourche  
By Hand  
Optional  
Opcional  
Optional  
Opcional  
Opzionale  
Optie  
A mano  
Von Hand  
Com a mão  
A mano  
Met de hand  
À la main  
En option  
Hex-Head Wrench  
Security Wrench  
Llave de cabeza hexagonal  
Sechskantschlüssel  
Chave de cabeça sextavada  
Chiave esagonale  
Llave de seguridad  
Sicherheitsschlüssel  
Chave de segurança  
Chiave di sicurezza  
Veiligheidssleutel  
Clé de sécurité  
Zeskantsleutel  
Clé à tête hexagonale  
4
 
MSM/MTM Series  
Installation Instructions  
TOOLS REQUIRED FOR INSTALLATION  
#2  
7/32" (5.5mm) Wood Stud  
5/16" (7.9mm) Concrete  
PARTS  
B (1)  
C (1)  
A (1)  
D (1)  
[Included with  
MSM6XXX/MTM6XXX  
Models Only]  
E (1)  
(MSM Only)  
Custom  
J (1) [Used on MSMU/MTMU Models Only]  
MSM6XXX/  
MTM6XXX  
Hardware  
F (1)  
(MSM Only)  
(MTM Only)  
J1 (8)  
J2 (6)  
J3 (6)  
M4x16mm M4x20mm  
M4x25mm  
J4 (6)  
M5x16mm  
J5 (6)  
J6 (6)  
G (1)  
(MTM Only)  
M5x20mm M5x25mm  
K (1)  
J9 (1)  
M5  
H (1)  
J7 (6)  
J8 (6)  
M6x16mm M6x25mm  
3/16" - 6"  
K2 (4)  
5/16"  
K1 (4)  
5/16"  
J12 (4)  
M8x50mm  
J11 (6)  
M8x30mm  
K3 (4)  
5/16" x 2-1/2"  
J10 (6)  
M8x20mm  
J15 (8)  
J14 (8)  
.750x.344x.500  
J13 (8)  
.750x.323x.250  
5
 
MSM/MTM Series  
Installation Instructions  
4. Measure up 7-1/2" from the center point to mark location of  
the upper mounting slots.  
INSTALLATION  
The MTM and MSM have been designed to be mounted directly  
onto either a wood stud or concrete wall. The MTM has  
brackets which allow the TV to be tilted. The MSM has static  
brackets which keep the TV in an upright position.  
5. Using a level, mark the wall on each stud to attach the  
mount through the upper mounting slots. (See Figure 2)  
NOTE: The MSM and MTM may be attached through the  
mounting slots on dual studs, or through the center  
mounting holes on a single stud. (See Figure 2)  
Locate Mounting Site  
5
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY  
OR DAMAGE TO EQUIPMENT! It is the installers  
responsibility to make certain the structure to which the  
mount is being attached is capable of supporting five times  
the weight of the MTM or MSM and all attached equipment  
not to exceed 125 lbs (56.7 kg) for dual stud attachment, and  
75 lbs (34.0 kg) for single stud attachment.  
NOTE: Proceed to either the Installing to a Wood Stud Wall  
section or the Installing to a Concrete Wall section.  
Installing to a Wood Stud Wall  
Single Stud  
Installation  
1. Determine the center of the TV screen, and where it should  
be located on the wall.  
2. Locate the closest stud to the left and right of the selected  
location.  
NOTE: If the screen area lies over a stud, use that stud if using  
the single stud installation method.  
5
NOTE: Use that stud and the stud to either the left or right of it  
if using the dual stud installation method.  
3. Line up the notches on mount with center of screen marking  
to determine vertical center. (See Figure 1)  
Center of screen  
7-1/2"  
Dual Stud  
Installation  
Figure 2  
Vertical center  
of mount  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL CORDS OR CABLES  
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!  
ALWAYS make certain area behind mounting surface is free  
of electrical wires and cables before drilling or installing  
fasteners.  
Figure 1  
6
 
Installation Instructions  
MSM/MTM Series  
9. Drill 7/32" pilot holes at markings for lower mounting holes.  
(See Figure 3)  
10. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) [one lag bolt and washer for single stud  
installation] to attach the mount to the wall through the lower  
mounting holes. (See Figure 3)  
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING  
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH  
OR SERIOUS PERSONAL INJURY! ALWAYS make certain  
area behind mounting surface is free of gas, water, waste, or  
any other plumbing before cutting, drilling, or installing  
fasteners.  
11. Slide rails to approximate center of screen location.  
Installing to a Concrete Wall  
1. Determine the center of the TV screen, and where it should  
be located on the wall.  
Dual Stud  
Installation  
x 4  
6
9
x
2. Line up the notches on mount with center of screen marking  
to determine vertical center. (See Figure 1)  
3. Measure up 7-1/2" from the center point to mark location of  
the upper mounting slots. (See Figure 1)  
4. Using a level, mark the wall through both upper mounting  
slots. (See Figure 4)  
WARNING: ELECTRICAL SHOCK HAZARD! CUTTING  
OR DRILLING INTO ELECTRICAL CORDS OR CABLES  
CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY!  
ALWAYS make certain area behind mounting surface is free  
of electrical wires and cables before drilling or installing  
fasteners.  
7
(K3) x 2  
(K2 x 4)  
10  
WARNING: EXPLOSION AND FIRE HAZARD! CUTTING  
OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH  
OR SERIOUS PERSONAL INJURY! ALWAYS make certain  
area behind mounting surface is free of gas, water, waste, or  
any other plumbing before cutting, drilling, or installing  
fasteners.  
(K3) x 2  
x 2  
6
9
6
x 2  
5
9
10  
(K2 x 2)  
7
10  
(K2 x 4)  
(K3) x 2  
Single Stud  
Installation  
7
(K3) x 2  
11  
Figure 3  
6. Drill one 7/32" pilot hole in each stud.  
Figure 4  
7. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) [one lag bolt and washer for single stud  
installation] to attach top of mount to wall. (See Figure 3)  
5. Drill one 5/16" pilot hole at each marking.  
6. Install an anchor (K1) into each pilot hole using a hammer.  
8. Mark the attachment points for the lower mounting slots,  
making sure the attachment points are located on the studs.  
(See Figure 3)  
7. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) to attach top of mount to anchors in wall.  
7
 
MSM/MTM Series  
Installation Instructions  
8. Mark the attachment points for the lower mounting slots.  
(See Figure 4)  
9. Drill one pilot hole at each marking for lower mounting  
holes. (See Figure 4)  
Mounting  
Holes  
10. Install an anchor (K1) into each pilot hole using a hammer.  
11. Use two 5/16 x 2-1/2" lag bolts (K3) and two 5/16" flat  
washers (K2) to attach the mount to the wall through the  
lower mounting holes. (See Figure 4)  
Mounting  
Slot  
1
12. Slide rails to approximate center of screen location.  
Knobs  
Attaching Interface Brackets to TV  
1. Align the center of the bracket with center of screen.  
(See Figure 5)  
NOTE: The diamond-shape hole in the bracket corresponds to  
the center of the mount.  
2
Figure 6  
Pull strap  
Center of bracket  
Figure 5  
WARNING: IMPROPER INSTALLATION CAN LEAD TO  
DISPLAY FALLING CAUSING SERIOUS PERSONAL  
INJURY OR DAMAGE TO EQUIPMENT! Using screws of  
improper size may damage your display. Properly sized  
screws will easily and completely thread into display  
mounting holes. If spacers are required, be sure to use longer  
screws of the same diameter.  
2. Select correct screws, spacers (if necessary) and washers  
from the hardware bag and attach brackets to back of  
screen. (See Figure 5)  
Switching Interface Brackets (Optional)  
If an installation situation makes adjusting the location of  
interface brackets necessary, there are several options.  
1. The wall bracket may be adjusted side to side at the point of  
attachment (mounting slots for dual stud installation,  
mounting holes for single stud installation). (See Figure )  
2. The location of the left and right interface brackets may be  
switched, with the knobs on the MTM interface brackets  
facing the inside of the mount. (See Figure )  
8
 
Installation Instructions  
MSM/MTM Series  
Center Line (CL)  
3d  
3e  
Pullstraps  
NEVER place both interface brackets to one  
side of the wall mount center line (CL)!  
Knobs to outside  
of brackets  
Figure 7  
3. If necessary, the tilt interface bracket knobs may be  
switched to allow the interface brackets to be reversed.  
(See Figure 7)  
a. Remove display from mount.  
b. Remove interface brackets from display.  
c. Hold the right interface bracket horizontally, tightly  
gripping it so that spacers do not move.  
d. Remove the knob, washer and screw.  
e. Replace the knob, washer and screw in the opposite  
order, with the knob on the inside of the bracket.  
f. Switch the right interface bracket to the left side of the  
wall mount.  
g. Repeat Steps 3c through 3f with the left interface  
bracket.  
Attaching Screen to Wall Mount  
Both interface brackets must NEVER be located  
to one side of the wall bracket!  
1. Adjust Velcro® pull strap (if necessary) so it does not  
extend beyond bottom of screen. (See Figure 8)  
NOTE: Do NOT allow both interface brackets to be located on  
same side of wall bracket. (See Figure 8)  
Figure 8  
NOTE: NEVER place both interface brackets to one side of the  
wall mount center line! (See Figure 8)  
9
 
MSM/MTM Series  
Installation Instructions  
1
Raises screen  
Lowers screen  
2
(H)  
Top  
Hook  
2
(Screen not  
shown for  
clarity)  
Figure 10  
Locking Mount (Optional)  
1. Add optional security bracket (F or G) to the mount.  
(See Figure 11)  
2. Add padlock (not included) to complete security.  
Pullstraps  
5
(Screen not shown for clarity)  
Figure 9  
(G)  
1
2
2. Hang top hook of interface brackets onto the top bar of the  
mount. (See Figure 9)  
NOTE: The screen initially installs into the "kickstand mode" to  
allow easy cable access.  
3. Slide screen and bars to desired viewing position.  
4. Route cables between wall and bars.  
(MTM Shown)  
Figure 11  
CAUTION: PINCH POINTS! Keep fingers, hands and  
cables out of pinch point areas.  
5. Pull downward on the pullstraps and swing inward toward  
wall, latching interface brackets to lower bar and locking  
bottom of screen to the mount. (See Figure 9)  
Adjusting Roll/Height of Wall Brackets  
NOTE: The height adjust wall bracket allows adjustment of  
+ 1/2".  
1. Turn to right (tighten) to raise side of screen.  
(See Figure 10)  
2. Turn to left (loosen) to lower side of the screen.  
10  
 
Installation Instructions  
MSM/MTM Series  
11  
 
MSM/MTM Series  
Installation Instructions  
USA/International  
Europe  
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378  
800.582.6480 / 952.894.6280  
877.894.6918 / 952.894.6918  
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands  
+31 (0)40 2668620  
+31 (0)40 2668615  
Chief Manufacturing, a division of  
Milestone AV Technologies  
Asia Pacific  
A
Room 24F, Block D, Lily YinDu International Building  
LuoGang, BuJi Town, Shenzhen, CHINA.  
8831-000024  
P
F
+86-755-8996 9226  
+86-755-8996 9217  
¤2008 Milestone AV Technologies  
09/08  
 

BenQ Thermometer SP920P User Manual
Black Decker Soldering Gun 722407 01 User Manual
Blodgett Hot Beverage Maker KLS 20G User Manual
Bosch Appliances Saw FPE 1000 SLC User Manual
Braun Thermometer IRT 4020 User Manual
Bravetti Food Processor FP86H User Manual
Briggs Stratton Portable Generator 40297 User Manual
Caframo Electric Heater 9206CA BBX User Manual
Carrier Furnace 58CLA User Manual
CDA Washer Dryer CI970 User Manual