Chief Manufacturing Indoor Furnishings MWC Series User Manual

I N S T A L L A T I O N I N S T R U C T I O N S  
MEDIUM FLAT PANEL TILT WALL MOUNT WITH  
INTEGRATED CPU  
Model: MWC Series  
Specifications:  
Accommodates three installation options:  
- Dual Wood Stud (16" on-center; requires  
5/16" x 2-1/2" long hex head lag screws -  
included)  
- Dual Steel Stud (requires Chief PAC-115  
Steel Stud / Drywall Anchor Kit - not included)  
- Drywall (1/2" minimum; requires Chief PAC-  
115 Steel Stud / Drywall Anchor Kit - not  
included)  
Accommodates CPU up to approximately 18-3/4"  
x 3-3/4"; see "DIMENSIONS" for specific details.  
Infinite display tilt adjustment between 0-15° with  
positive stops at 0°, 5°, 10°, and 15°.  
Weight capacity of 100 lbs (45 kg).  
NOTE: Requires display interface providing 200x200mm  
mounting button pattern; not included.  
BEFORE YOU BEGIN  
WARNING: It is the installer’s responsibility to make sure all components are properly assembled and installed  
using the instructions provided. Failure to read, thoroughly understand, and follow all instructions can result in  
serious personal injury, damage to equipment, or voiding of factory warranty.  
If you have any questions about this these instructions or your specific installation, contact Chief Manufacturing  
at 1-800-582-6480 or 952-894-6280.  
8804-000296 RevB  
CHIEF MANUFACTURING INC.  
1-800-582-6480 952-894-6280 FAX 952-894-6918  
8401 EAGLE CREEK PARKWAY, STE 700  
SAVAGE, MINNESOTA 55378 USA  
¤2007 Chief Manufacturing  
10/07  
 
Installation Instructions  
Model: MWC Series  
TOOLS REQUIRED FOR INSTALLATION  
PARTS  
Stud Sensor  
After unpacking carton, inspect and verify contents  
(See Figure 1). If any listed parts are missing or  
damaged, contact Chief Customer Service at 1-800-582-  
6480.  
Drill  
5/32" Drill Bit  
1/2" Wrench  
5/32" Security Hex Key (included)  
Table 1: Parts  
NOTE: Other tools may be required depending on your  
method of installation.  
Item  
10  
20  
30  
40  
50  
60  
70  
80  
Description  
Qty  
1
MOUNT, MWC Series  
STRAP, 1" x 6’ Polypropylene with Cam Buckle  
SCREW, Button Head Security, 1/4"-20 x 1/2"  
SCREW, Button Head Cap, 1/4"-20 x 1/2"  
NUT, Hex, Standard, 1/4"-20  
KEY, Security Hex, 5/32"  
1
4
2
2
1
SCREW, Hex Head Lag, 5/16 x 2-1/2"  
WASHER, Flat, 5/16"  
4
4
10  
20  
30  
40  
50  
60  
70  
80  
Figure 1: Parts  
3
 
Model: MWC Series  
Installation Instructions  
CPU INSTALLATION  
INSTALLATION  
MOUNT INSTALLATION  
WARNING: Exceeding the weight capacity can result  
in serious personal injury or damage to equipment! It is  
the installer’s responsibility to make sure the combined  
weight of all components attached to the MWC Series  
Wall Mount, including the CPU and display, does not  
exceed 100 lbs (45 kg).  
Three installation options exist:  
Dual Wood Stud (16" on-center; requires 5/16" x  
2-1/2" long hex head lag screws)  
Dual Steel Stud (requires Chief PAC-115 Steel  
Stud / Drywall Anchor Kit; not included)  
Drywall (1/2" minimum; requires Chief PAC-115  
Steel Stud / Drywall Anchor Kit; not included)  
1. Using key (60) remove and retain upper front plate  
attach screws and washers (See Figure 3).  
The following instructions are for dual wood stud  
installation. See instructions included with PAC-115 for  
dual steel stud or drywall installation.  
NOTE: Lower front plate attach screws may remain  
installed.  
1. Determine approximate mounting location, keeping in  
mind the display size.  
2. Use a stud sensor to locate applicable wood studs.  
Mark locations with a pencil.  
Upper front plate  
Front  
3. Level mount at desired height. Using mount as a  
template, mark the location of four pilot holes. Ensure  
marks are in the center of wood studs.  
attach screws and  
Plate  
washers (2 places)  
4. Drill pilot holes using a 7/32" drill bit. Ensure pilot  
holes are straight.  
5. Using 1/2" wrench, install four 5/16" x 2-1/2" hex head  
lag screws (70) and four 5/16" washers (80) through  
the mounting slots in the side plates into the pilot  
holes (See Figure 2). Tighten all lag screws.  
NOTE: Drywall not  
shown for clarity.  
Figure 3: Upper Front Plate Attach Screws  
2. Tilt front plate away from wall and then lift out of lower  
front plate attach screws (See Figure 4). Place front  
plate on protective surface.  
Side Plates  
2
(80) x 4  
(70) x 4  
Lower front  
plate attach  
screws  
1
(2 places)  
Figure 2: Mount Installation  
Front Plate  
Figure 4: Remove Front Plate  
3. Loosely thread strap (20) through side plates so that  
buckle is in front (See Figure 5).  
4
 
Installation Instructions  
Model: MWC Series  
DISPLAY INSTALLATION  
WARNING: Exceeding the weight capacity can result  
in serious personal injury or damage to equipment! It is  
the installer’s responsibility to make sure the combined  
weight of all components attached to the MWC Series  
Wall Mount, including the CPU and display, does not  
exceed 100 lbs (45 kg).  
Side Plates  
1. Install interface (providing 200x200mm mounting  
button pattern) to display. See instructions supplied  
with interface.  
20  
2. Rotate Q-Latch to the OPEN position (See Figure 7).  
Figure 5: Install Strap  
4. Carefully slide CPU between strap (20) and rear  
surface of side plates (See Figure 6). Ensure the  
following:  
OPEN  
Both loops of strap (20) are in front of the CPU; do  
not wrap strap (20) around back of CPU.  
CPU is positioned so that cooling vents are not  
obstructed.  
Q-Latch  
Figure 7: Open Q-Latch  
3. Lift and maneuver display so that all four mounting  
buttons fit into button openings on front plate. Lower  
display firmly into place. Ensure each button has fully  
seated in its button opening (See Figure 8).  
Mounting buttons  
(4 places)  
CPU  
Button Openings  
(4 places)  
Figure 6: Insert CPU  
5. Tighten strap (20) securely.  
6. Re-install front plate by reversing the procedure in  
Step 2:  
Tilt the top of the front plate towards you.  
Lower the front plate onto the lower attach  
screws.  
Front Plate  
Tilt the top of the front plate away from you  
(towards the wall).  
NOTE: Display and  
interface not shown for clarity.  
7. Using key (60), re-install the retained upper front plate  
attach screws and washers removed in Step 1.  
Figure 8: Align and Lower Display  
NOTE: If desired, security screws (30) may be  
substituted for non-security screws at both upper  
and lower attach points.  
4. Rotate Q-Latch to the CLOSED position (See Figure  
9).  
5
 
Model: MWC Series  
Installation Instructions  
NOTE: If Q-Latch does not fully close, ensure mounting  
TILT LOCK  
buttons are fully seated in the button openings.  
1. If desired, the display may be locked at 0°, 5°, or 10°.  
NOTE: A hole is provided in both the Q-Latch and the  
front plate to accommodate the insertion of a  
padlock or similar locking device.  
NOTE: A positive stop exists at 15° without the use of an  
additional locking screw.  
Slightly loosen the upper front plate attach  
screws. Do NOT remove screws.  
Using key (60), loosely install screws (40) through  
the slot in the front plate, through the applicable  
open tilt lock hole in the side plate, into nut (50)  
(See Figure 11)(See Figure 12).  
NOTE: Display and interface  
not shown for clarity.  
Tilt display until lock is reached.  
Locking device  
installed here  
Tighten all four screws (upper front plate attach,  
and 40).  
Tilt lock holes  
(Right side shown;  
left side similar)  
Q-Latch  
CLOSED  
10° 5° 0°  
Figure 9: Close Q-Latch  
Upper front plate  
attach screws  
(Right side shown;  
left side similar)  
WARNING: Make sure the latch securing the display  
is fully closed at all times except when removing or  
installing the display. The latch must be fully closed  
when installing or removing cables from the display.  
5. Attach all cables to display and CPU.  
Figure 11: Tilt Lock Holes  
TILT ADJUSTMENT  
1. If desired, the display may be tilted to any position  
between 0° and 15°.  
Slightly loosen upper front plate attach screws  
(See Figure 10). Do NOT remove screws.  
50 (2 places)  
Tilt display to desired angle.  
Tighten upper attach screws.  
40 (2 places)  
Upper front plate  
attach screws  
(2 places)  
Side plate  
Front plate  
NOTE: Display  
shown at 15°  
position.  
Figure 10: Tilt Adjustment  
Figure 12: Tilt Lock Screw Installation  
6
 

Blue Rhino Gas Grill HBT601B User Manual
Bolens Lawn Mower 620 thru 669 User Manual
Bosch Appliances Mixer MFQ 2100 UC User Manual
Bosch Power Tools Sander 0601276939 User Manual
Bose Speaker 141 User Manual
Bravetti Frozen Dessert Maker KP300H User Manual
Cabletron Systems Network Router 9T106 01 User Manual
Carson Stereo Amplifier HA 150 10 User Manual
Channel Vision Switch P 1205 User Manual
Chicago Electric Welder 92496 User Manual