I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Plasma Ceiling Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PCM SERIES
Installation Instructions
PCM SERIES
TOOLS REQUIRED FOR INSTALLATION AND PARTS
3/16" (provided)
A (1)
B (1)
I/M
C (1)
D (6)
x1
DIMENSIONS
Figure 1
3
PCM SERIES
Installation Instructions
Mount Assembly and Installation
Display Installation
1. Fold tube out until tube mounting bracket rests against
faceplate mounting bracket. (See Figure 2)
If the mounting pattern of the display being installed is a VESA
standard 200 x 200 pattern the mounting buttons can be
installed directly to the back of the display. If the display has any
other mounting pattern an interface bracket must be obtained
before proceeding. Consult a Chief Customer Service
representative if an interface bracket is required by calling
2. Secure tube to faceplate mounting bracket using 3/16" hex
wrench (C) and two 5/16-18 x 1/2" button head cap screws
(D).
3. Tighten all hardware.
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Displays can weigh in
excess of 40 lbs (18.1kg). ALWAYS use two people and
proper lifting techniques when installing display.
1
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT. Make sure mounting buttons
on display are properly seated in mounting holes in faceplate.
To install display:
1. While supporting both sides of display, align four mounting
buttons on display or interface bracket with four mounting
holes in faceplate. (See Figure 4)
2. Lower display into place listening for audible "click" to
ensure recessed area of mounting buttons are properly
seated in lower area of mounting holes and "click lock"
mechanism has engaged. (See Figure 4) and
(See Figure 5)
(D) x 2
2
Figure 2
4. Thread the tube assembly (A) onto 1-1/2” NPT.
NOTE: The product is suitable for use with a Listed ceiling
plate which can accommodate 1-1/2" NPT pipe, and
has a rated weight capacity of 200 lbs (91 kg).
5. Secure faceplate (B) to faceplate mounting bracket using
3/16" hex wrench (C) and four 5/16-18 x 1/2" button head
cap screws (D).
1
(A) x1
(B) x 1
2
Figure 4
(D) x4
5
NOTE: Holes are provided in the faceplate for use with a
padlock or similar locking device, if desired. In addition,
the pin and nut may be removed from the upper holes
and moved to the lower holes for use as a more
permanent locking device. (See Figure 5)
Figure 3
4
Installation Instructions
PCM SERIES
Display Roll Adjustment
To adjust display roll:
1. Loosen 3/8-16 Nylock nut. (See Figure 7)
To use as a
more permanent
lock, remove pin
and nuts and move
to lower holes
2. Adjust faceplate to desired position. (See Figure 7)
3. Tighten 3/8-16 Nylock nut. (See Figure 7)
1
2
1
A padlock or bolt may
be placed through latch holes
Figure 5
2
3
Adjustments
The PCM is designed to accommodate 5" of display height
adjustment, 4º right and left display roll adjustment, and 15º
down/5º up display pitch (Tilt) adjustment.
Remove display before performing adjustments.
Figure 7
Display Height Adjustment
To adjust display height:
Display Pitch (Tilt) Adjustment
To adjust display pitch:
1. Loosen four 5/16-18 button head cap screws using 3/16"
hex wrench (C). (See Figure 6)
2. Adjust faceplate to desired position. (See Figure 6)
3. Tighten four 5/16-18 button head cap screws using 3/16"
hex wrench (C). (See Figure 6)
1. Loosen four 5/16-18 button head cap screws.
(See Figure 8)
2. Adjust to desired tilt position. (See Figure 8)
3. Tighten four 5/16-18 button head cap screws.
(See Figure 8)
1
3
1
2
3
2
Figure 8
Figure 6
5
PCM SERIES
Installation Instructions
6
Installation Instructions
PCM SERIES
7
PCM SERIES
Installation Instructions
Chief® and ClickConnect™ are trademarks of Milestone AV Technologies, Inc. All rights reserved.
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
Chief Manufacturing, a division of
Milestone AV Technologies
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8805-000114 RevE
©2008 Milestone AV Technologies
04/08
P
F
+86-755-8996 9226
+86-755-8996 9217
|