Child Craft Crib CCH0070109 00 User Manual

1
CCH00701:09/00 JCHE p65  
15061,16101,16151,16191,16281  
DOUBLEDROPSIDE CRIB  
child craft  
CHILD CRAFT INDUSTRIES, INC.  
P.O. Box 444, Salem, IN USA 47167-0444  
ASSEMBLY DIRECTIONS AND PARTS LIST  
ΦREADALLINSTRUCTIONSWITHCAREBEFORESTARTINGTHEASSEMBLYPROCEDURE.  
Φ YOUWILLNEEDA#2PHILLIPSSCREWDRIVER,ASLOTTEDSCREWDRIVERANDAHAMMER.  
PARTS ENCLOSEDIN HARDWARE BAG(NOTED WHEN SHOWN ACTUAL SIZE)  
(12) Slotted/Phillips  
Machine Screws  
(4) Spring Hangers  
(4) Gate Shoes  
(18) Slotted/Phillips  
Wood Screws  
A
B
C
D
E
(2)  
Moulded  
plastic  
(actual size)  
(actual size)  
(2)  
4-Position  
Spring  
Hanger  
Brackets  
backers  
(4) Casters  
(style may vary)  
(4) Compression  
(4) Bumper  
Springs  
(2) Angle  
Brackets  
F
G
H
I
Springs  
PARTS INCLUDED IN CARTON  
(1) Spring  
(1) Footboard  
(1) Headboard  
(2) Stabilizer Bars  
O
N
P
&
Q
R
J
K
(2) Crib sides  
(Dropsides)  
(4) Crib Rods  
PREPARATION  
Carefully remove and lay out all hardware and parts. Remove wires securing the (2) Stabilizer Bars J and the (4) Crib Rods K to Crib Spring R. Check  
quantities and match to the three Parts Lists above. If any part is missing or broken contact your dealer or Child Craft (P.O. Box 444, Salem, IN 47167-  
0444 USA (ph# 812/883-3111), [email protected] for a replacement part or instructional literature. Before making this contact, identify your crib.  
A model identification number is stamped on the underneath side of the bottom rail of either a crib end N/O or a crib side P/Q. Record the model  
Identification Number now: # ______________________. Include this number with a request for a part or instructional literature. DO NOT SUBSTITUTE  
PARTS!  
STEP 1-DIAGRAM 1:ATTACH OF 4-POSITION SPRING HANGER BRACKETS AND ANGLE BRACKETS.  
Note the two piece assembly of 4-Position Spring Hanger Brackets D. Before  
attachment to crib (ends) N &O, check to be sure the moulded plastic backer  
aligns with the 4-Position Spring Hanger Bracket D as shown. These items are  
shipped assembled, in the unlikely event they should become detached during  
shipment, simply take the plastic backer, align with the holes in the metal bracket  
O
and snap together to create an assembly as shown in the Hardware Parts Diagram.  
Holes to  
IMPORTANT! All four plastic tabs on each moulded plastic backer should project  
toward the metal hooks on 4-Position Spring Hanger Brackets D. If you should  
find a tab on an uninstalled 4-Position Spring Hanger Bracket not so projected,  
simply use a screwdriver to push tab forward until it contacts the metal hook. If  
a plastic tab is not projected on a factory installed 4-Position Spring Hanger Bracket  
simply place a small slotted screwdriver underneath the plastic tab and pull  
forward until it contacts the metal hook. Attach a 4-Position Spring Hanger Bracket  
D, (2 piece assembly), to both Headboard N & Footboard O with Slotted/Phillips  
Wood Screws E, to be positioned exactly as the ones already factory installed.  
Attach Angle Brackets I with Slotted/Phillips Wood Screws E to Headboard N  
and Footboard O, to be positioned exactly as the ones already factory installed.DO  
NOT REMOVE 4-POSITION SPRING HANGER BRACKETS OR ANY OTHER  
HARDWARE ITEMATTACHEDWITHSLOTTED/PHILLIPSWOODSCREWS E.  
D
receive  
Slotted/  
Phillips  
Wood  
Screws  
E
D
E
Factory  
installed  
I
E
 
3
CCH00701:09/00  
MAIN DIAGRAM 6  
TIGHTEN SCREW A MANUALLY, DO NOT USE ANY TYPE OF POWER SCREWDRIVER.  
O
N
A
A
K
K
P / Q  
Top rail  
D
Plastic  
pouch  
B
J
F
G
I
H
Locate the 4 Casters H, insert each into a  
Foot latch  
lower corner post of Headboard N/Footboard  
O. Refer to Main Diagram 6. (Caster H  
design may possibly vary according to your  
particular crib model.)  
P / Q  
Bottom rail  
CAUTION: If crib is placed on exception-  
ally thick carpet, take care when crib is  
rolled as Casters H could catch on thick  
carpet pile and possibly cause breakage  
or damage to lower corner posts of crib.  
CLOSE UP VIEW  
K
D
Hook end  
down  
CRIB SPRING R:  
R
Be sure the smooth side of wire is  
placed up as illustrated. Also,style  
of Crib Spring R may differ with  
your model of crib.  
H
B
J
Permanent Storage of Assembly Instructions: After completing the assembly  
process you are advised to read and be aware of all WARNINGS, CAUTIONS,  
CLEANING, STORAGE, USE, and MAINTENANCE notices contained in this set of  
assembly directions and printed on the plastic pouch located on the underneath side of  
crib spring. You will then place this complete set of assembly directions into the plastic  
pouch for future referral. We caution you not to place excess hardware in the plastic  
pouch as it could present danger to a small child if retrieved.  
Place a purchased mattress on Crib Spring R and crib is ready for use.  
TO RAISE & LOWER CRIB DROPSIDE: To lower lift the dropside  
slightly, pushthefootlatchtowardtheinsideofcribwhichwillrelease  
thedropsidetothelowest or"DOWN"position.Toraisethedropside,  
lift up on the dropside, rail will then lock into the "UP" position.  
 
4
CCH00701:09/00  
WARNING  
CAUTION  
!
Φ ANY MATTRESS USED IN THIS  
CRIB MUST BE AT LEAST 27-1/4  
INCHES (69 CENTIMETERS), BY 51-  
5/8 INCHES (131 CENTIMETERS),  
WITH A THICKNESS NOT EXCEED-  
ING 6 INCHES (15 CENTIMETERS).  
thedimensionsofthemattressshall  
betakenfromseamtoseamoredge  
to edge where appropriate.  
Φ FAILURE TO FOLLOW THESE WARNINGS AND ASSEM-  
BLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY  
OR DEATH.  
Φ READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB.  
KEEP INSTRUCTIONS FOR FUTURE USE. A plastic pouch  
is attached to crib spring for permanent storage of the  
instructionalliterature.  
Φ BEFORE EACH USAGE OR ASSEMBLY, INSPECT CRIB  
FOR DAMAGED HARDWARE, LOOSE JOINTS, MISSING  
PARTS OR SHARP EDGES. DO NOT USE CRIB IF ANY  
PARTSAREMISSINGORBROKEN.ASKYOURDEALEROR  
CHILD CRAFT, P.O. BOX 444, SALEM, IN 47167-0444 USA  
(812/883-3111) [email protected] FOR REPLACE-  
MENT PARTS AND INSTRUCTIONAL LITERATURE IF  
Φ UPON COMPLETION OF ASSEM-  
BLY BE SURE ALL SCREWS,  
BOLTS AND FASTENING DEVICES  
HAVE BEEN TIGHTENED SE-  
CURELY. A FREQUENT CHECK  
NEEDED. INCLUDE MODEL IDENTIFICATION NUMBERS SHOULD BE MADE OF ALL  
WITH YOUR REQUEST WHICH YOU RECORDED ON PAGE  
ONE. DO NOT SUBSTITUTE PARTS.  
SCREWS, BOLTS AND FASTENING  
DEVICES AND TIGHTEN IF  
NEEDED.  
MAINTENANCEOFYOURCHILDCRAFTCRIB:Upon  
completion of assembly be sure all screws, bolts and  
fastening devices have been tightened securely. A  
frequent periodic check should be made of all screws,  
bolts and fastening devices and tighten if needed. Before  
each usage or assembly, inspect crib for damaged  
hardware, loose joints, missing parts or sharp edges. DO  
NOT use crib if parts are missing or broken. Ask your  
Φ AFTER RAISING SIDE, MAKE SURE LATCHES ARE SE-  
CURE.  
Φ WHEN CHILD IS ABLE TO CLIMB OUT OR REACHES THE  
HEIGHTOF35INCHES(90CENTIMETERS)THECRIBSHALL  
NO LONGER BE USED.  
Φ DO NOT PLACE CRIB NEAR WINDOW WHERE CORDS  
Dealer  
or  
Child  
Craft  
(812/883-3111),  
FROM BLINDS OR DRAPES MAY STRANGLE A CHILD.  
[email protected] for replacement parts and  
instructional literature if needed. Include Model Identifi-  
cation Number with your request which you recorded on  
page 1. DO NOT substitute parts. DO NOT make any  
alteration to this crib.  
CLEANINGINSTRUCTIONSFORYOURCHILDCRAFT  
CRIB: Mixtogetheramildsolutionofgentledishwashing  
liquid and water, apply to crib surface using a soft clean  
cloth lightly dampened in the solution. Rinse with clear  
water again using a soft clean cloth then dry all surfaces  
thoroughly with a soft dry cloth. NO ABRASIVE CLEAN-  
ERS, SCOURING PADS, STEEL WOOL, OR COARSE  
RAGSSHOULDBEUSEDTOCLEANTHISFINEFURNI-  
TURE.  
Φ IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED  
FOR CHILDREN'S PRODUCTS.  
Φ DO NOT LEAVE CHILD IN CRIB WITH SIDE LOWERED. BE  
SURE SIDE IS IN RAISED AND LOCKED POSITION WHEN-  
EVER CHILD IS IN CRIB.  
Φ WHENCHILDISABLETOPULLTOSTANDINGPOSITION,  
SET MATTRESS TO LOWEST POSITION AND REMOVE  
BUMPERPADS,LARGETOYSANDOTHEROBJECTSTHAT  
COULD SERVE AS STEPS FOR CLIMBING OUT.  
STORAGEANDUSEOFYOURCHILDCRAFTCRIB:  
A
Φ NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLAS-  
TIC FILM AS MATTRESS COVERS BECAUSE THEY CAN  
CAUSE SUFFOCATION.  
printed plastic pouch is attached to the crib spring for the  
permanent storage of the assembly directions. After  
completing the assembly process you are advised to  
readandbeawareofallWARNINGS,CAUTIONS,CLEAN-  
ING,STORAGE,USEANDMAINTENANCEnoticescon-  
tained in this set of assembly directions and printed on  
the plastic pouch located on the underneath side of crib  
spring. You will then place the complete set of assembly  
directions into the plastic pouch for future referral. We  
caution you not to place excess hardware in the plastic  
pouch as it could present danger to a child if retrieved and  
it could also puncture crib mattress. When storing crib  
use CAUTION as extreme temperature or humidity  
changes could be harmful. Use CAUTION when a vapor-  
izer is in use, always aim vaporstream away from crib  
as well as away from any other wood furniture item.  
Φ DO NOT USE A WATER MATTRESS WITH THIS CRIB.  
Φ REPLACE TEETHING RAIL(S) IF DAMAGED OR LOOSE.  
Φ STRINGSCANCAUSESTRANGULATION!DONOTPLACE  
ITEMS WITH A STRING AROUND A CHILD'S NECK, SUCH  
AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUS-  
PEND STRINGS OVER A CRIB OR ATTACH STRINGS TO  
TOYS.  
Φ REMOVE ALL CRIB TOYS WHICH ARE STRUNG ACROSS  
CRIB AREA WHEN YOUR CHILD IS BEGINNING TO PUSH  
UP ON HANDS AND KNEES OR IS 5 MONTHS OF AGE,  
WHICHEVER OCCURS EARLIEST. THESE TOYS CAN  
CAUSE STRANGULATION!  
CCH00701:09/00 JCHE p65  
madeinusa  
Φ WHEN DISASSEMBLING THIS CRIB, DO NOT REMOVE  
ANY ITEM ATTACHED WITH WOOD SCREWS.  
Φ ALWAYS ENSURE A SAFE ENVIRONMENT FOR THE  
CHILD BY CHECKING REGULARLY, BEFORE PLACING  
THE CHILD IN THE CRIB, THAT EVERY COMPONENT IS  
PROPERLY AND SECURELY IN PLACE.  
CHILDCRAFTINDUSTRIES,INC.  
P.O. Box 444, Salem, IN USA 47167-0444  
PH: 812-883-3111 - FAX: 812-883-1819  
 

Blackberry Home Theater Server blackberry enterprise server for microsoft exchange User Manual
Black Box Switch ACU1006DRA User Manual
Blue Rhino Patio Heater EWTR890SP User Manual
Bose Headphones in ear headphone User Manual
Cambridge SoundWorks Speaker System I755 User Manual
Carrier Gas Heater 48HC User Manual
Casablanca Fan Company Fan 54028 User Manual
Casio Computer Monitor 700AR1A User Manual
Chamberlain Garage Door Opener 1345M User Manual
Cisco Systems IP Phone OL 12727 01 User Manual