Installation, Operation
and
4
NWHO
(Supersedes PE429)
PE429-1
161-058065-001
RENEWAL PARTS IDENTIFICATION
FEBRUARY, 1986
Type NWHO-45, 72, 108
Circulation Heaters for
Regular and Fuel Oil
Heating
E
2 x 3/
Slot
4
”
1”
B
Specifications – Table A
Dimensions (In.)
No. 3Ø
813/16”
Model
NWHO-4590
NWHO-45125 240 or 480 125
NWHO-45150 240 or 480 150
NWHO-45175 240 or 480 175
NWHO-45200 240 or 480 200
Volts 3Ø
240 or 480
kW
90
Circuits
A
B
C
D
E
D
5
5
5
5
5
721/
871/
1021/
1171/
125 251/
2
251/
251/
251/
251/
2
635/
785/
935/
1085/
1161/
8
1813/
1813/
1813/
16
16
16
16
16
121/
121/
121/
121/
121/
2
2
2
8
2
5 Conduit
Outlets
2
2
8
2
2
2
8
1813/
2
72° Apart
or
2
8
1813/
2
C
A
6” Outlet
NWHO-77220 240 or 480 200
NWHO-77225 240 or 480 225
NWHO-77250 240 or 480 250
6
6
6
971/ 273/
1051/ 273/
1131/ 273/
981/ 291/
1041/ 291/
1101/ 291/
2
4
885/
965/
1045/
8
19
19
19
193/
193/
193/
133/
133/
133/
141/
141/
141/
4
6 Conduit
Outlets
Mounting
Lug Centers
2
4
8
4
2
4
8
4
60° Apart
Temperature
Control
NWHO-108300 240 or 480 300
NWHO-108325 240 or 480 325
NWHO-108350 240 or 480 350
6
6
6
2
2
895/
955/
1011/
16
16
16
8
2
2
2
8
2
2
2
8
2
These Dimensions are typical. Check factory for dimensions of a particular unit.
6” Inlet
GENERAL
The high capacity NWHO-45, 72 or 108 series are intended for
indoor use and are used primarily for oil heating.
temperatures and to limit internal temperatures under abnormal
flow conditions. These controls do not fail-safe.
The 45, 72 or 108 steel sheathed tubular elements are centered
in a 14”, 16” or 18” diameter steel heating chamber, respectively,
and welded to a removable steel flange. The assembly is sur-
rounded by 2” of insulation and a sheet metal jacket.
Depending upon the order specifications, the NWHO-45, 72 or
108 may or may not be factory equipped with an MF2 or other
Chromalox thermostat. Such thermostats function to control outlet
CAUTION: Users should install adequate back-up
controls and safety devices with their electric
heating equipment. Where the consequences of
failure may be severe, back-up controls are essen-
tial. Although the safety of the installation is the
responsibility of the user, Chromalox will be glad to
make equipment recommendations.
INSTALLATION
1. Vertical mounting (axis of chamber
vertical) is preferred. Check factory
for constructions suitable for hori-
zontal mounting.
2. Mount heater with terminal enclo-
sure at top, and use lower nozzle as
inlet to the circulating fluid.
should be bolted solidly; however, the remaining lug should be
bolted loosely to allow freedom of movement with expansion.
5. DANGER: Hazard of Fire. Provide minimum of 6” spac-
ing from chamber and related piping to nearest combustible
material. Avoid operation of heater near combustible fluids or
in combustible vapor or gas laden atmosphere. Note: Contact
factory for heaters suitable for use in hazardous locations.
6. Provide adequate space at terminal end to permit withdrawal of
the heater from chamber should servicing be required.
7. If two or more heaters are needed to provide the needed heat-
ing capacity, arrange them for series flow.
8. DANGER: Possible Explosion. A pressure relief valve
should be provided by customer at outlet of vessel. There
should be no valving between vessel and relief valve.
3. The NWHO-45, 72 and 108 series
of circulation heaters are provided
with mounting lugs to support the
heater chamber. Refer to Figure A
for one suggested mode of support.
4. Mount heaters to permit unre-
strained expansion of chamber due
Figure A
to temperature. The large flange lug
© 2010 Chromalox, Inc.
|