C H A P T E R
3
Network Configuration
This chapter details concepts and procedures for configuring the Cisco Secure Access Control Server
Release 4.1, hereafter referred to as ACS. You use the configuration process to establish a distributed
system, and set up interaction with authentication, authorization, and accounting (AAA) clients and
servers. You can also configure remote agents for the ACS Solution Engine.
This chapter contains the following topics:
•
•
•
•
•
•
•
•
•
About Network Configuration
The appearance of the page that you see when you click Network Configuration differs according to the
network-configuration selections that you made in the Interface Configuration section.
The tables that might appear in this section are:
•
•
AAA Clients—This table lists each AAA client that is configured on the network, together with its
IP address and associated protocol.
If you are using Network Device Groups (NDGs), this table does not appear on the initial page, but
is accessed through the Network Device Group table. For more information about this interface
configuration, see Displaying Advanced Options, page 2-5.
AAA Servers—This table lists each AAA server that is configured on the network together with its
IP address and associated type. After installation, this table automatically lists the machine on which
ACS is installed. In ACS SE, the name of the machine is listed as self.
If you are using Network Device Groups (NDGs), this table does not appear on the initial page, but
is accessed through the Network Device Group table. For more information about this interface
configuration, see Displaying Advanced Options, page 2-5.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1
Chapter 3 Network Configuration
Proxy in Distributed Systems
These types of access control have unique authentication and authorization requirements. With ACS,
system administrators can use a variety of authentication methods that are used with different degrees
of authorization privileges.
Completing the AAA functionality, ACS serves as a central repository for accounting information. Each
user session that ACS grants can be fully accounted for, and its accounting information can be stored in
the server. You can use this accounting information for billing, capacity planning, and security audits.
Note
If the fields mentioned in this section do not appear in the ACS web interface, you can enable them by
choosing Interface Configuration > Advanced Options. Then, check the Distributed System Settings
check box.
Default Distributed System Settings
You use the AAA Servers table and the Proxy Distribution Table to establish distributed system settings.
The parameters that are configured within these tables create the foundation so that you can configure
multiple ACSs to work with one another. Each table contains an ACS entry for itself. In the AAA Servers
table, the only AAA server that is initially listed is itself (in ACS SE, the server name is listed as self);
the Proxy Distribution Table lists an initial entry of (Default), which displays how the local ACS is
configured to handle each authentication request locally.
You can configure additional AAA servers in the AAA Servers table. These devices can, therefore,
become visible in the web interface so that they can be configured for other distributed features such as
proxy, ACS internal database replication, remote logging, and RDBMS synchronization. For
Proxy in Distributed Systems
Proxy is a powerful feature that enables you to use ACS for authentication in a network that uses more
than one AAA server. This section contains the following topics:
•
•
•
•
The Proxy Feature
Using proxy, ACS automatically forwards an authentication request from AAA clients to AAA servers.
After the request has been successfully authenticated, the authorization privileges that you configured
for the user on the remote AAA server are passed back to the original ACS, where the AAA client applies
the user profile information for that session.
Proxy provides a useful service to users, such as business travelers, who dial in to a network device other
than the one they normally use and would otherwise be authenticated by a foreign AAA server. To
configure proxy, you choose Interface Configuration > Advanced Options. Then, check the
Distributed System Settings check box.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -3
Chapter 3 Network Configuration
Proxy in Distributed Systems
An Example
This section presents a scenario of proxy that is used in an enterprise system. Mary is an employee with
Mary needs access to the network, she accesses the network locally and authenticates her username and
password. Because Mary works in the Los Angeles office, her user profile, which defines her
authentication and authorization privileges, resides on the local Los Angeles AAA server.
However, Mary occasionally travels to a division within the corporation in New York, where she still
needs to access the corporate network to get her e-mail and other files. When Mary is in New York, she
recognize her username, but the Proxy Distribution Table contains an entry, @la.corporate.com, to
forward the authentication request to the Los Angeles ACS. Because the username and password
information for Mary reside on that AAA server, when she authenticates correctly, the AAA client in the
New York office applies the authorization parameters that are assigned to her.
Proxy Distribution Table
Whether, and where, an authentication request is to be forwarded is defined in the Proxy Distribution
Table on the Network Configuration page. You can use multiple ACSs throughout your network. For
information about configuring the Proxy Distribution Table, see Configuring Proxy Distribution Tables,
ACS employs character strings that the administrator defines to determine whether an authentication
request should be processed locally or forwarded, and where. When an end user dials in to the network
device and ACS finds a match for the character string defined in the Proxy Distribution Table, ACS
forwards the authentication request to the associated remote AAA server.
Note
Note
When an ACS receives a TACACS+ authentication request forwarded by proxy, any requests for
Network Access Restrictions for TACACS+ are applied to the IP address of the forwarding AAA server,
not to the IP address of the originating AAA client.
When an ACS proxies to a second ACS, the second ACS responds to the first by using only IETF
attributes, no VSAs, when it recognizes the first ACS as the AAA server. Alternatively, you can
configure the second ACS to see an ACS as a AAA client; in this case, the second ACS responses include
the RADIUS VSAs for whatever RADIUS vendor is specified in the AAA client definition table
entry—in the same manner as any other AAA client.
Administrators with geographically dispersed networks can configure and manage the user profiles of
employees within their immediate location or building. The administrator can, therefore, manage the
policies of just their users and all authentication requests from other users within the company can be
forwarded to their respective AAA server for authentication. Not every user profile must reside on every
AAA server. Proxies save administration time and server space, and allows end users to receive the same
privileges regardless of the access device through which they connect.
Fallback on Failed Connection
You can configure the order in which ACS checks remote AAA servers if a failure of the network
connection to the primary AAA server occurs. If an authentication request cannot be sent to the first
listed server, because of a network failure for example, the next listed server is checked. This checking
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -4
Chapter 3 Network Configuration
Proxy in Distributed Systems
continues, in order, down the list, until the AAA servers handles the authentication request. (Failed
connections are detected by failure of the nominated server to respond within a specified time period.
That is, the request is timed out.) If ACS cannot connect to any server in the list, authentication fails.
Character String
ACS forwards authentication requests by using a configurable set of characters with a delimiter, such as
periods (.), slashes (/), or hyphens (-). When configuring the ACS character string, you must specify
whether the character string is the prefix or suffix. For example, you can use domain.us as a suffix
character string in username*domain.us, where the asterisk (*) represents any delimiter. An example of
a prefix character string is domain.*username, where the asterisk (*) would be used to detect the slash(/).
Stripping
Stripping allows ACS to remove, or strip, the matched character string from the username. When you
enable stripping, ACS examines each authentication request for matching information. When ACS finds
a match by character string in the Proxy Distribution Table, as described in the example under Proxy in
Distributed Systems, page 3-3, ACS strips off the character string if you have configured it to do so. For
example, in the following proxy example, the character string that accompanies the username establishes
the ability to forward the request to another AAA server. If the user must enter the user ID of
[email protected] to be forwarded correctly to the AAA server for authentication, ACS might find
a match on the @corporate.com character string, and strip the @corporate.com, leaving a username of
mary, which might be the username format that the destination AAA server requires to identify the
correct entry in its database.
Note
Realm stripping does not work with Extensible Authentication Protocol (EAP)-based authentication
protocols, such as Protected Extensible Authentication Protocol (PEAP) or Extensible Authentication
Protocol-Flexible Authentication via Secure Tunneling (EAP-FAST). For example, if you are using
Protected Extensible Authentication Protocol Microsoft Challenge Authentication Handshake Protocol
(PEAP MSCHAP), authentication will fail if a realm is stripped by proxy.
Remote Use of Accounting Packets
When proxy is employed, ACS can dispatch AAA accounting packets in one of three ways:
Log them locally.
Forward them to the destination AAA server.
Log them locally and forward copies to the destination AAA server.
Sending accounting packets to the remote ACS offers several benefits.
•
•
•
•
When ACS is configured to send accounting packets to the remote AAA server, the remote
AAA server logs an entry in the accounting report for that session on the destination server. ACS
also caches the user connection information and adds an entry in the List Logged on Users report.
You can then view the information for users that are currently connected. Because the accounting
information is sent to the remote AAA server, even if the connection fails, you can view the Failed
Attempts report to troubleshoot the failed connection.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -5
Chapter 3 Network Configuration
Network Device Searches
•
Sending the accounting information to the remote AAA server also enables you to use the Max
Sessions feature. The Max Sessions feature uses the Start and Stop records in the accounting packet.
If the remote AAA server is an ACS and the Max Sessions feature is implemented, you can track
the number of sessions that are allowed for each user or group.
•
You can also choose to have Voice-over-IP (VoIP) accounting information logged remotely,
appended to the RADIUS Accounting log, entered in a separate VoIP Accounting log, or both.
Other Features Enabled by System Distribution
Beyond basic proxy and fallback features, configuring an ACS to interact with distributed systems
enables several other features that are beyond the scope of this chapter. These features include:
•
•
•
Replication—For more information, see ACS Internal Database Replication, page 8-1.
RDBMS synchronization—For more information, see RDBMS Synchronization, page 8-17.
Remote and centralized logging—For more information, see Remote Logging for ACS for
Windows, page 10-9, and Remote Logging for ACS SE with ACS Remote Agents, page 10-10.
Network Device Searches
You can search for any network device that is configured in the Network Configuration section of the
ACS web interface.
This section contains the following topics:
•
•
Network Device Search Criteria
You can specify search criteria for network device searches. ACS provides the following search criteria:
•
Name—The name assigned to the network device in ACS. You can use an asterisk (*) as a wildcard
character. For example, if you wanted to find all devices with names starting with the letter M, you
would enter M* or m*. Name-based searches are case insensitive. If you do not want to search based
on device name, you can leave the Name box blank or you can put only an asterisk (*) in the Name
box.
•
IP Address—The IP address specified for the network device in ACS. For each octet in the address,
you have three options:
–
–
Number—You can specify a number, for example, 10.3.157.98.
Numeric Range—You can specify the low and high numbers of the range in the octet, separated
by a hyphen (-), for example, 10.3.157.10-50.
–
Wildcard—You can use an asterisk (*) to match all numbers in that octet, for example,
10.3.157.*.
ACS allows any octet or octets in the IP Address box to be a number, a numeric range, or an asterisk
(*), for example 172.16-31.*.*.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -6
Chapter 3 Network Configuration
Network Device Searches
•
•
Type—The device type, as specified by the AAA protocol that it is configured to use, or the kind of
AAA server it is. You can also search for Solution Engine remote agents. If you do not want to limit
the search based on device type, choose Any from the Type list.
Device Group—The NDG to which the device is assigned. This search criterion only appears if you
have enabled Network Device Groups on the Advanced Options page in the Interface Configuration
section. If you do not want to limit the search based on NDG membership, select Any from the
Device Group list.
Searching for Network Devices
To search for a network device:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Click Search.
The Search for Network Devices page appears. In the configuration area, the controls for setting search
criteria appear above the search results for the most recent search that was previously conducted for this
session, if any.
Tip
When you leave the Search for Network Devices page, ACS retains your search criteria and
results for the duration of the current administrative session. Until you log out of ACS, you can
return to the Search for Network Devices page to view your most recent search criteria and
results.
Step 3
Step 4
Set the criteria for a device search. For information about search criteria, see Network Device Search
Tip
To reset the search criteria to default settings, click Clear.
Click Search.
A table lists each network device configured in ACS that matches the search criteria you specified. If
ACS did not find a matching network device, the message No Search Resultsappears.
The table listing that matches network devices includes the device name, IP address, and type. If you
have enabled Network Device Groups on the Advanced Options page in the Interface Configuration
Section, the table also includes the NDG of each matching network device.
Tip
You can sort the table rows by whichever column you want, in ascending or descending order.
Click a column title once to sort the rows by the entries in that column in ascending order. Click
the column a second time to sort the rows by the entries in that column in descending order.
Step 5
If you want to view the configuration settings for a network device found by the search, click the network
device name in the Name column in the table of matching network devices.
ACS displays the applicable setup page. For information about the AAA Client Setup page, see AAA
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -7
Chapter 3 Network Configuration
Configuring AAA Clients
Step 6
Step 7
If you want to download a file containing the search results in a comma-separated value format, click
Download, and use your browser to save the file to a location and filename of your choice.
If you want to search again by using different criteria, repeat Step 3 and Step 4.
Configuring AAA Clients
This guide uses the term “AAA client” comprehensively to signify the device through which or to which
service access is attempted. This is the RADIUS or TACACS+ client device, and may comprise Network
Access Servers (NASs), PIX Firewalls, routers, or any other RADIUS or TACACS+ hardware or
software client.
This section contains the following topics:
•
•
•
•
AAA Client Configuration Options
AAA client configurations enable ACS to interact with the network devices that the configuration
represents. A network device that does not have a corresponding configuration in ACS, or whose
configuration in ACS is incorrect, does not receive AAA services from ACS.
The Add AAA Client and AAA Client Setup pages include:
•
AAA Client Hostname—The name that you assign to the AAA client configuration. Each AAA
client configuration can represent multiple network devices; thus, the AAA client hostname
configured in ACS is not required to match the hostname configured on a network device. We
recommend that you adopt a descriptive, consistent naming convention for AAA client hostnames.
Maximum length for AAA client hostnames is 32 characters.
Note
After you submit the AAA client hostname, you cannot change it. If you want to use a
different name for AAA clients, delete the AAA client configuration and create a new AAA
client configuration by using the new name.
•
AAA Client IP Address—At a minimum, a single IP address of the AAA client or the keyword
dynamic.
If you only use the keyword dynamic, with no IP addresses, the AAA client configuration can only
be used for command authorization for Cisco multi device-management applications, such as
Management Center for Firewalls. ACS only provides AAA services to devices based on IP address;
so it ignores such requests from a device whose AAA client configuration only has the keyword
dynamic in the Client IP Address box.
If you want the AAA client configuration in ACS to represent multiple network devices, you can
specify multiple IP addresses. Separate each IP address by pressing Enter.
In each IP address that you specify, you have three options for each octet in the address:
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -8
Chapter 3 Network Configuration
Configuring AAA Clients
–
–
Number—You can specify a number, for example, 10.3.157.98.
Numeric Range—You can specify the low and high numbers of the range in the octet, separated
by a hyphen (-), for example, 10.3.157.10-50.
–
Wildcard—You can use an asterisk (*) to match all numbers in that octet, for example,
10.3.157.*.
ACS allows any octet or octets in the IP Address box to be a number, a numeric range, or an asterisk
(*), for example 172.16-31.*.*.
•
•
Shared Secret—The shared secret key of the AAA client. Maximum length for the AAA client key
is 32 characters.
For correct operation, the key must be identical on the AAA client and ACS. Keys are case sensitive.
If the shared secret does not match, ACS discards all packets from the network device.
Network Device Group—The name of the NDG to which this AAA client should belong. To make
the AAA client independent of NDGs, use the Not Assigned selection.
Note
This option does not appear if you have not configured ACS to use NDGs. To enable NDGs,
choose Interface Configuration > Advanced Options. Then, check the Network Device
Groups check box.
•
RADIUS Key Wrap—The shared secret keys for RADIUS Key Wrap in EAP-TLS authentications.
Each key must be unique, and must also be distinct from the RADIUS shared key. These shared keys
are configurable for each AAA Client, as well as for each NDG. The NDG key configuration
overrides the AAA Client configuration.
–
Key Encryption Key (KEK)—This is used for encryption of the Pairwise Master Key (PMK).
In ASCII mode, enter a key length of exactly 16 characters; in hexadecimal mode, enter a key
length of 32 characters.
–
Message Authentication Code Key (MACK)—This is used for the keyed hashed message
authentication code (HMAC) calculation over the RADIUS message. In ASCII mode, enter a
key length of exactly 20 characters; in hexadecimal mode, enter a key length of 40 characters.
Note
If you leave a key field empty when key wrap is enabled, the key will contain only zeros.
–
Key Input Format—Select whether to enter the keys as ASCII or hexadecimal strings (the
default is ASCII).
Note
You must enable the Key Wrap feature in the NAP Authentication Settings page to
implement these shared keys in EAP-TLS authentication.
•
Authenticate Using—The AAA protocol to use for communications with the AAA client. The
Authenticate Using list includes Cisco IOS TACACS+ and several vendor-specific implementations
of RADIUS. If you have configured user-defined RADIUS vendors and VSAs, those vendor-specific
RADIUS implementations appear on the list also. For information about creating user-defined
RADIUS VSAs, see Custom RADIUS Vendors and VSAs, page 8-19.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -9
Chapter 3 Network Configuration
Configuring AAA Clients
The Authenticate Using list always contains:
–
TACACS+ (Cisco IOS)—The Cisco IOS TACACS+ protocol, which is the standard choice
when using Cisco Systems access servers, routers, and firewalls. If the AAA client is a Cisco
device-management application, such as Management Center for Firewalls, you must use this
option.
–
–
RADIUS (Cisco Airespace)—RADIUS using Cisco Airespace VSAs. Select this option if the
network device is a Cisco Airespace WLAN device supporting authentication via RADIUS.
RADIUS (Cisco Aironet)—RADIUS using Cisco Aironet VSAs. Select this option if the
network device is a Cisco Aironet Access Point used by users who authenticate with the
Lightweight and Efficient Application Protocol (LEAP) or the Extensible Authentication
Protocol-Transport Layer Security (EAP-TLS) protocol, provided that these protocols are
enabled on the Global Authentication Setup page in the System Configuration section.
When an authentication request from a RADIUS (Cisco Aironet) AAA client arrives, ACS first
attempts authentication by using LEAP; if this fails, ACS fails over to EAP-TLS. If LEAP is
not enabled on the Global Authentication Setup page, ACS immediately attempts EAP-TLS
authentication. If neither LEAP nor EAP-TLS is enabled on the Global Authentication Setup,
any authentication attempt received from a Cisco Aironet RADIUS client fails. For more
information about enabling LEAP or EAP-TLS, see Global Authentication Setup, page 9-19.
Using this option enables ACS to send the wireless network device a different session-timeout
value for user sessions than ACS sends to wired end-user clients.
Note
If all authentication requests from a particular Cisco Aironet Access Point are PEAP or
EAP-TLS requests, use RADIUS (IETF) instead of RADIUS (Cisco Aironet). ACS cannot
support PEAP authentication by using the RADIUS (Cisco Aironet) protocol.
–
–
RADIUS (Cisco BBSM)—RADIUS using Cisco Broadband Services Manager (BBSM)
Vendor Specific Attributes (VSAs). Select this option if the network device is a Cisco BBSM
network device supporting authentication via RADIUS.
RADIUS (Cisco IOS/PIX 6.0)—RADIUS using Cisco IOS/PIX 6.0 VSAs. This option enables
you to pack commands sent to a Cisco IOS or Project Information Exchange (PIX)S 6.0 AAA
client. The commands are defined in the Group Setup section. Select this option for RADIUS
environments in which key TACACS+ functions are required to support Cisco IOS and PIX
equipment.
–
RADIUS (Cisco VPN 3000/ASA/PIX7.x+)—RADIUS using Cisco VPN 3000 concentrator,
ASA device, and PIX 7.x device VSAs. Select this option if the network device is a Cisco VPN
3000 series concentrator, an ASA, or PIX 7.x+ device supporting authentication via RADIUS.
–
–
RADIUS (Cisco VPN 5000)—RADIUS using Cisco VPN 5000 VSAs. Select this option if the
network device is a Cisco VPN 5000 series Concentrator.
RADIUS (IETF)—IETF-standard RADIUS, using no VSAs. Select this option if the AAA
client represents RADIUS-enabled devices from more than one manufacturer and you want to
use standard IETF RADIUS attributes. If the AAA client represents a Cisco Aironet Access
Point used only by users who authenticate with PEAP or EAP-TLS, this is also the protocol to
select.
–
–
RADIUS (Ascend)—RADIUS using Ascend RADIUS VSAs. Select this option if the network
device is an Ascend network device that supports authentication via RADIUS.
RADIUS (Juniper)—RADIUS using Juniper RADIUS VSAs. Select this option if the network
device is a Juniper network device that supports authentication via RADIUS.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 0
Chapter 3 Network Configuration
Configuring AAA Clients
–
–
RADIUS (Nortel)—RADIUS using Nortel RADIUS VSAs. Select this option if the network
device is a Nortel network device that supports authentication via RADIUS.
RADIUS (iPass)—RADIUS for AAA clients using iPass RADIUS. Select this option if the
network device is an iPass network device supporting authentication via RADIUS. The iPass
RADIUS is identical to IETF RADIUS.
•
Single Connect TACACS+ AAA Client (Record stop in accounting on failure)—If you select
TACACS+ (Cisco IOS) from the Authenticate Using list, you can use this option to specify that ACS
use a single TCP connection for all TACACS+ communication with the AAA client, rather than a
new one for every TACACS+ request. In single connection mode, multiple requests from a network
device are multiplexed over a single TCP session. By default, this check box is unchecked.
Note
If TCP connections between ACS and the AAA client are unreliable, do not use this feature.
•
Log Update/Watchdog Packets from this AAA Client—Enables logging of update or watchdog
packets. Watchdog packets are interim packets that are sent periodically during a session. They
provide you with an approximate session length if the AAA client fails and, therefore, no stop packet
is received to mark the end of the session. By default, this check box is unchecked.
•
•
Log RADIUS Tunneling Packets from this AAA Client—Enables logging of RADIUS tunneling
accounting packets. Packets are recorded in the RADIUS Accounting reports of Reports and
Activity. By default, this check box is unchecked.
Replace RADIUS Port info with Username from this AAA Client—Enables use of username,
rather than port number, for session-state tracking. This option is useful when the AAA client cannot
provide unique port values, such as a gateway GPRS support node (GGSN). For example, if you use
the ACS IP pools server and the AAA client does not provide a unique port for each user, ACS
assumes that a reused port number indicates that the previous user session has ended and ACS may
reassign the IP address that was previously assigned to the session with the non-unique port number.
By default, this check box is unchecked.
Note
If this option is enabled, ACS cannot determine the number of user sessions for each user.
Each session uses the same session identifier, the username; therefore, the Max Sessions
feature is ineffective for users accessing the network through the AAA client with this
feature enabled.
•
Match Framed-IP-Address with user IP address for accounting packets from this AAA
Client—Select this option when the AAA client uses Cisco SSL WebVPN. This action ensures that
ACS assigns different IP addresses to two different users when they log in via a Cisco SSL WebVPN
client. By default, this check box is unchecked.
Adding AAA Clients
You can use this procedure to add AAA client configurations.
Before You Begin
For ACS to provide AAA services to AAA clients, you must ensure that gateway devices between AAA
clients and ACS allow communication over the ports needed to support the applicable AAA protocol
(RADIUS or TACACS+). For information about ports that AAA protocols use, see AAA
Protocols—TACACS+ and RADIUS, page 1-3.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 1
Chapter 3 Network Configuration
Configuring AAA Clients
To add AAA clients:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Do one of the following:
•
If you are using NDGs, click the name of the NDG to which you want to assign the AAA client.
Then, click Add Entry below the AAA Clients table.
•
To add AAA clients when you have not enabled NDGs, click Add Entry below the AAA Clients
table.
The Add AAA Client page appears.
Step 3
Step 4
Enter the AAA client settings, as needed. For information about the configuration options available for
To save your changes and apply them immediately, click Submit + Apply.
Note
Restarting the service clears the Logged-in User report and temporarily interrupts all ACS
services. This action affects the Max Sessions counter.
Tip
If you want to save your changes and apply them later, choose Submit. When you are ready to
implement the changes, choose System Configuration > Service Control. Then, choose
Restart.
Editing AAA Clients
You can use the following procedure to edit the settings for AAA client configurations.
Note
You cannot directly edit the names of AAA clients; rather, you must delete the AAA client entry and
then reestablish the entry with the corrected name. For steps about deleting AAA client configurations,
Before You Begin
For ACS to provide AAA services to AAA clients, you must ensure that gateway devices between AAA
clients and ACS permit communication over the ports that support the applicable AAA protocol
(RADIUS or TACACS+). For information about ports that AAA protocols use, see AAA
Protocols—TACACS+ and RADIUS, page 1-3.
To edit AAA clients:
Step 1
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 2
Chapter 3 Network Configuration
Configuring AAA Clients
Step 2
Do one of the following:
•
If you are using NDGs, click the name of the NDG to which the AAA client is assigned. Then, click
the name of the AAA client.
•
To edit AAA clients when you have not enabled NDGs, click the name of the AAA client in the AAA
Client Hostname column of the AAA Clients table.
The AAA Client Setup For Name page appears.
Step 3
Modify the AAA client settings, as needed. For information about the configuration options available
Note
You cannot directly edit the name of the AAA client; rather, you must delete the AAA client
entry and then re-establish the entry with the corrected name. For steps about deleting the AAA
Step 4
To save your changes and apply them immediately, click Submit + Apply.
Tip
To save your changes and apply them later, choose Submit. When you are ready to implement
the changes, choose System Configuration > Service Control. Then, choose Restart.
Note
Restarting the service clears the Logged-in User report and temporarily interrupts all ACS
services. This action affects the Max Sessions counter.
Configuring a Default AAA Client
You can configure a default AAA Client to accommodate any unrecognized AAA Clients (NAS):
Step 1
Step 2
Step 3
Leave the AAA Client Hostname and AAA Client IP address blank.
Complete the rest of the fields and continue with the rest of the procedure for adding AAA Clients.
Note
Only TACACS+ can have a default AAA Client configured. The default name for the client is Others
and the default IP address is 0.0.0.0.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 3
Chapter 3 Network Configuration
Configuring AAA Servers
Deleting AAA Clients
To delete AAA clients:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Do one of the following:
•
If you are using NDGs, click the name of the NDG to which the AAA client is assigned. Then, click
the AAA client hostname in the AAA Clients table.
•
To delete AAA clients when you have not enabled NDGs, click the AAA client hostname in the
AAA Clients table.
The AAA Client Setup for the Name page appears.
Step 3
To delete the AAA client and have the deletion take effect immediately, click Delete + Apply.
Note
Restarting ACS services clears the Logged-in User report and temporarily interrupts all ACS
services. As an alternative to restarting when you delete AAA clients, you can click Delete.
However, when you do, the change does not take effect until you restart the system, which you
can do by choosing System Configuration > Service Control. Then, choose Restart.
A confirmation dialog box appears.
Click OK.
Step 4
ACS restarts AAA services and the AAA client is deleted.
If you have a configured RADIUS/TACACS source-interface command on the AAA client, ensure that
you configure the client on ACS by using the IP address of the interface that is specified.
Configuring AAA Servers
This section presents procedures for configuring AAA servers in the ACS web interface. For additional
To configure distributed system features for a given ACS, you must first define the other AAA server(s).
For example, all ACSs that are involved in replication, remote logging, authentication proxying, and
RDBMS synchronization must have AAA server configurations for each other; otherwise, incoming
communication from an unknown ACS is ignored and the distributed system feature will fail.
Tip
If the AAA Servers table does not appear, choose Interface Configuration > Advanced Options. Then,
check the Distributed System Settings check box.
This section contains the following topics:
•
•
•
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 4
Chapter 3 Network Configuration
Configuring AAA Servers
•
AAA Server Configuration Options
AAA server configurations enable ACS to interact with the AAA server that the configuration represents.
AAA servers that do not have a corresponding configuration in ACS, or whose configuration in ACS is
incorrect, do not receive AAA services from ACS, such as proxied authentication requests, database
replication communication, remote logging, and RDBMS synchronization. Also, several distributed
systems features require that the other ACSs included in the distributed system be represented in the
AAA Servers table. For more information about distributed systems features, see About ACS in
After installation, the AAA Servers table automatically lists the machine on which ACS is installed. This
machine is also defined as the default proxy server in the Proxy Distribution table, and appears by default
in the RDBMS table.
Note
In ACS SE, the name of the machine in the AAA servers table is listed as self; in the Proxy Distribution
and RDBMS tables the appliance hostname is listed.
The Add AAA Server and AAA Server Setup pages include the following options:
•
AAA Server Name—The name that you assign to the AAA server configuration. The AAA server
hostname that is configured in ACS does not have to match the hostname configured on a network
device. We recommend that you adopt a descriptive, consistent naming convention for AAA server
names. Maximum length for AAA server names is 32 characters.
Note
After you submit the AAA server name, you cannot change it. If you want to use a different
name for the AAA server, delete the AAA server configuration and create the AAA server
configuration by using the new name.
•
•
AAA Server IP Address—The IP address of the AAA server, in dotted, four-octet format. For
example, 10.77.234.3.
Key—The shared secret of the AAA server. Maximum length for AAA server keys is 32 characters.
For correct operation, the key must be identical on the remote AAA server and ACS. Keys are case
sensitive. Because shared secrets are not synchronized, you could easily to make mistakes when
entering them on remote AAA servers and ACS. If the shared secret does not match, ACS discards
all packets from the remote AAA server.
•
Network Device Group—The name of the NDG to which this AAA server should belong. To make
the AAA server independent of NDGs, use the Not Assigned selection.
Note
This option does not appear if you have not configured ACS to use NDGs. To enable NDGs,
choose Interface Configuration > Advanced Options. Then, check the Network Device
Groups check box.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 5
Chapter 3 Network Configuration
Configuring AAA Servers
•
•
Log Update/Watchdog Packets from this remote AAA Server—Enables logging of update or
watchdog packets from AAA clients that are forwarded by the remote AAA server to this ACS.
Watchdog packets are interim packets that are sent periodically during a session. They provide you
with an approximate session length if the AAA client fails and, therefore, no stop packet is received
to mark the end of the session.
AAA Server Type—One of types:
–
–
–
RADIUS—Select this option if the remote AAA server is configured by using any type of
RADIUS protocol.
TACACS+—Select this option if the remote AAA server is configured by using the TACACS+
protocol.
ACS—Select this option if the remote AAA server is another ACS. This action enables you to
configure features that are only available with other ACSs, such as ACS internal database
replication and remote logging.
•
Traffic Type—The Traffic Type list defines the direction in which traffic to and from the remote
AAA server is permitted to flow from this ACS. The list includes:
–
–
–
Inbound—The remote AAA server accepts requests that have been forwarded to it and does not
forward the requests to another AAA server. Select this option if you do not want to permit any
authentication requests to be forwarded from the remote AAA server.
Outbound—The remote AAA server sends out authentication requests but does not receive
them. If a Proxy Distribution Table entry is configured to proxy authentication requests to the
AAA server that is configured for Outbound, the authentication request is not sent.
Inbound/Outbound—The remote AAA server forwards and accepts authentication requests,
allowing the selected server to handle authentication requests in any manner that is defined in
the distribution tables.
•
•
AAA Server RADIUS Authentication Port—Specify the port on which the AAA server accepts
authentication requests. The standard port is 1812, and another commonly used port is 1645. If you
select TACACS+ in the AAA Server Type field, this RADIUS Authentication Port field is dimmed.
AAA Server RADIUS Accounting Port—Specify the port on which the AAA server accepts
accounting information. The standard port is 1813, and another commonly used port is 1646. If you
select TACACS+ in the AAA Server Type field, this RADIUS Accounting Port field is dimmed.
Adding AAA Servers
Before You Begin
For descriptions of the options that are available while adding a remote AAA server configuration, see
For ACS to provide AAA services to a remote AAA server, you must ensure that gateway devices
between the remote AAA server and ACS permit communication over the ports that support the
applicable AAA protocol (RADIUS or TACACS+). For information about ports that AAA protocols use,
see AAA Protocols—TACACS+ and RADIUS, page 1-3.
To add and configure AAA servers:
Step 1
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 6
Chapter 3 Network Configuration
Configuring AAA Servers
Step 2
Do one of the following:
•
If you are using NDGs, click the name of the NDG to which the AAA server is to be assigned. Then,
click Add Entry below the [name] AAA Servers table.
•
To add AAA servers when you have not enabled NDGs, below the AAA Servers table, click Add
Entry.
The Add AAA Server page appears.
Step 3
Step 4
Enter the AAA server settings, as needed. For information about the configuration options available for
To save your changes and apply them immediately, click Submit + Apply.
Tip
To save your changes and apply them later, choose Submit. When you are ready to implement
the changes, choose System Configuration > Service Control. Then, choose Restart.
Note
Restarting the service clears the Logged-in User report and temporarily interrupts all ACS
services. This action affects the Max Sessions counter and resets it to (0).
Editing AAA Servers
Use this procedure to edit the settings for AAA servers that you have previously configured.
Note
You cannot edit the names of AAA servers. To rename AAA servers, you must delete the existing AAA
server entry and then add a new server entry with the new name.
Before You Begin
For descriptions of the options available while editing a remote AAA server entry, see AAA Server
For ACS to provide AAA services to a remote AAA server, you must ensure that gateway devices
between the remote AAA server and ACS permit communication over the ports that support the
applicable AAA protocol (RADIUS or TACACS+). For information about ports that AAA protocols use,
see AAA Protocols—TACACS+ and RADIUS, page 1-3.
To edit AAA servers:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Do one of the following:
•
If you are using NDGs, click the name of the NDG to which the AAA server is assigned. Then, in
the AAA Servers table, click the name of the AAA server to be edited.
•
If you have not enabled NDGs, in the AAA Servers table, click the name of the AAA server to be
edited.
The AAA Server Setup for X page appears.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 7
Chapter 3 Network Configuration
Configuring Remote Agents (ACS Solution Engine Only)
Step 3
Step 4
Enter or change AAA server settings, as needed. For information about the configuration options
To save your changes and apply them immediately, click Submit + Apply.
Tip
To save your changes and apply them later, choose Submit. When you are ready to implement
the changes, choose System Configuration > Service Control. Then, choose Restart.
Note
Restarting the service clears the Logged-in User report and temporarily interrupts all ACS
services. This action affects the Max Sessions counter and resets it to (0).
Deleting AAA Servers
To delete AAA servers:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Do one of the following:
•
If you are using NDGs, click the name of the NDG to which the AAA server is assigned. Then, click
the AAA server name in the AAA Servers table.
•
If you have not enabled NDGs, click the AAA server name in the AAA Servers table.
The AAA Server Setup for X page appears.
Step 3
To delete the AAA server and have the deletion take effect immediately, click Delete + Apply.
Note
Restarting the service clears the Logged-in User report and temporarily interrupts all ACS
services. As an alternative to restarting when you delete AAA servers, in the preceding step you
can click Delete. However, when you do this, the change does not take effect until you restart
the system, which you can do by choosing System Configuration > Service Control. Then,
choose Restart.
A confirmation dialog box appears.
Click OK.
Step 4
ACS performs a restart and the AAA server is deleted.
Configuring Remote Agents (ACS Solution Engine Only)
This section presents information about remote agents and procedures for configuring remote agents in
the ACS web interface.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 8
Chapter 3 Network Configuration
Configuring Remote Agents (ACS Solution Engine Only)
This section contains the following topics:
•
•
•
•
•
About Remote Agents
An ACS Solution Engine can use remote agents for remote logging and authentication of users with a
Windows external user database. Before you can configure remote logging and authentication by using
a Windows external user database, you must add at least one remote agent configuration to the Remote
Agents table in the Network Configuration section.
For more information about remote agents, including how to install and configure them, see the
Installation Guide for Cisco Secure ACS Solution Engine Release 4.1.
Remote Agent Configuration Options
The Add Remote Agent and Remote Agent Setup pages include the following options:
Note
A remote agent that does not have a corresponding configuration in ACS, or whose configuration
in ACS is incorrect, cannot communicate with ACS to receive its configuration, logging data, or
Windows authentication requests.
•
Remote Agent Name—The name that you assign to the remote agent configuration. You configure
remote agent logging and Windows authentication by using remote agent names. We recommend
that you adopt a descriptive, consistent naming convention for remote agents. For example, you
could assign the same name as the hostname of the server that runs the remote agent. The maximum
length for a remote agent name is 32 characters.
Note
After you submit the remote agent name, you cannot change it. If you want to use a different
name for a remote agent, delete the remote agent configuration, create a new remote agent
configuration by using the new name, and change remote logging and Windows
authentication configurations that use the remote agent.
•
•
Remote Agent IP Address—The IP address of the remote agent, in dotted-decimal format. For
example, 10.77.234.3.
Remote Agent Port—The TCP port on which the remote agent listens for communication from
ACS. The maximum length for the TCP port number is 6 characters. The Remote Agent Port must
be a numeric value in the range of 0 to 65535.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -1 9
Chapter 3 Network Configuration
Configuring Remote Agents (ACS Solution Engine Only)
Note
If the port number that you provide does not match the port the remote agent that you
configured for listening, ACS cannot communicate with the remote agent. For information
about configuring the remote agent port, see the Installation and Configuration Guide for
Cisco Secure ACS Remote Agents Release 4.1.
•
Network Device Group—The name of the NDG to which this remote agent should belong. To make
the remote agent independent of NDGs, chose the Not Assigned selection.
In addition to the options in the preceding list, the Remote Agent Setup page includes the following
options:
•
Running Status—Information about the status of the remote agent. If ACS can contact the remote
agent, the uptime for the remote agent appears. If ACS cannot contact the remote agent, the message
Not respondingappears.
•
Configuration Provider—The ACS from which the remote agent receives its configuration.
Tip
Click on the ACS name to access the web interface for the ACS that provides configuration data
to a remote agent. A new browser window displays the web interface for the ACS that provides
configuration data to the remote agent.
•
Service Table—ACS displays a table of remote agent services below the Configuration Provider.
The table includes the following columns:
–
Service—A list of services that a remote agent can provide: remote logging and Windows
authentication.
–
–
Available—Whether the remote agent can currently provide the corresponding service.
Used by this ACS—Whether the ACS into which you are logged is currently using the
corresponding service.
Adding a Remote Agent
Before You Begin
For descriptions of the options available while adding a remote agent configuration, see Remote Agent
For ACS to communicate with a remote agent, you must ensure that gateway devices between a remote
agent and ACS permit communication over the TCP ports used by remote agents. For information about
ports used by remote agents, see the Installation and Configuration Guide for Cisco Secure ACS Remote
Agents Release 4.1.
To add and configure a remote agent:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration section opens.
Perform one of the following steps, based on your use of NDGs:
a. If you are using NDGs, click the name of the NDG to which you want to assign the remote agent.
Then, in the NDG Remote Agents table, click Add Entry.
b. If you are not using NDGs, click Add Entry in the Remote Agents table.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 0
Chapter 3 Network Configuration
Configuring Remote Agents (ACS Solution Engine Only)
The Add Remote Agent page appears.
Step 3
Step 4
Step 5
In the Remote Agent Name box, type a name for the remote agent (up to 32 characters).
In the Remote Agent IP Address box, type the IP address of the computer that runs the remote agent.
In the Port box, type the number of the TCP port on which the remote agent listens for communication
from ACS (up to 6 digits). The default TCP port is 2003.
Note
If this port number does not match the port on which the remote agent is configured to listen,
ACS cannot communicate with the remote agent. For information about configuring the port
number on which the remote agent listens, see the Installation and Configuration Guide for
Cisco Secure ACS Remote Agents Release 4.1.
Step 6
Step 7
From the Network Device Group list, select the NDG to which this remote agent belongs.
Note
The Network Device Group list appears only if NDGs are enabled. To enable NDGs, click
Interface Configuration > Advanced Options, and then click Network Device Groups.
To save your changes and immediately apply them, click Submit + Apply.
Tip
To save your changes and apply them later, click Submit. When you are ready to implement the
changes, click System Configuration > Service Control, and then click Restart.
Note
Restarting the service clears the Logged-in User report and temporarily interrupts all ACS
services. The Max Sessions counter is reset to 0.
Editing a Remote Agent Configuration
Use this procedure to edit the settings for a remote agent that you have previously configured.
Note
You cannot edit the name of a remote agent. If you want to use a different name for a remote agent, delete
the remote agent configuration, create a remote agent configuration by using the new name, and change
remote logging and Windows authentication configurations that use the remote agent.
Before You Begin
For descriptions of the options available while editing a remote agent configuration, see Remote Agent
Note
For ACS to communicate with a remote agent, you must ensure that gateway devices between a
remote agent and ACS permit communication over the TCP ports used by remote agents. For
information about ports used by remote agents, see the Installation and Configuration Guide for
Cisco Secure ACS Remote Agents Release 4.1.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 1
Chapter 3 Network Configuration
Configuring Remote Agents (ACS Solution Engine Only)
To edit a remote agent configuration:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration section opens.
Perform one of the following steps, based on your use of NDGs:
a. If you are using NDGs, click the name of the NDG to which the remote agent belongs. Then, in the
NDG Remote Agents table, click the name of the remote agent configuration you want to edit.
b. If you are not using NDGs, in the Remote Agents table, click the name of the remote agent that you
want to edit.
The Remote Agent Setup for the agent page appears.
Step 3
Enter or select new settings for one or more of the following options:
•
•
•
Remote Agent IP Address
Port
Network Device Group (displayed if enabled in Advanced Options in the interface configuration)
Note
If the ACS into which you are currently logged does not provide configuration data for the
remote agent, none of the options can be edited. You can access the web interface for the ACS
that does provide configuration data to the remote agent by clicking the ACS name listed as the
Configuration Provider.
Step 4
To save your changes and apply them immediately, click Submit + Apply.
Tip
To save your changes and apply them later, click Submit. When you are ready to implement the
changes, click System Configuration > Service Control, and then click Restart.
Note
Restarting the service clears the Logged-in User report and temporarily interrupts all ACS
services. The Max Sessions counter is reset to 0.
Deleting a Remote Agent Configuration
Note
You cannot delete a remote agent that you have configured to use for remote logging or Windows
authentication.
To delete a remote agent configuration:
Step 1
In the navigation bar, click Network Configuration.
The Network Configuration section opens.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 2
Chapter 3 Network Configuration
Configuring Network Device Groups
Step 2
Perform one of the following steps, based on your use of NDGs:
a. If you are using NDGs, click the name of the NDG to which the remote agent belongs. Then, in the
NDG Remote Agents table, click the name of the remote agent configuration you want to delete.
b. If you are not using NDGs, in the Remote Agents table, click the name of the remote agent
configuration that you want to delete.
The Remote Agent Setup for the agent page appears.
Step 3
To delete the remote agent and have the deletion take effect immediately, click Delete + Apply.
Note
Restarting services clears the Logged-in User report and temporarily interrupts all ACS services.
As an alternative to restarting when you delete a remote agent, in the preceding step you can
click Delete. However, when you do this, the change does not take effect until you restart
services, which you can do by clicking System Configuration > Service Control > Restart.
A confirmation dialog box appears.
Click OK.
Step 4
ACS restarts its services and the remote agent configuration is deleted.
Configuring Network Device Groups
Network Device Grouping is an advanced feature that you use to view and administer a collection of
network devices as a single logical group. To simplify administration, you can assign each group a name
that can be used to refer to all devices within that group. This action creates two levels of network
devices within ACS—single discrete devices such as an individual router or network-access server, and
an NDG; that is, a collection of routers or AAA servers.
Caution
To see the Network Device Groups table in the web interface, you must check the Network Device
Groups option on the Advanced Options page of the Interface Configuration section. Unlike in other
areas of Interface Configuration, it is possible to remove from sight an active NDG if you uncheck the
Network Device Groups option. Therefore, if you choose to configure NDGs, ensure that you leave the
Network Device Groups option selected on the Advanced Option page.
This section contains the following topics:
•
•
•
•
•
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 3
Chapter 3 Network Configuration
Configuring Network Device Groups
Adding a Network Device Group
You can assign users or groups of users to NDGs. For more information, see:
•
•
Setting TACACS+ Enable Password Options for a User, page 6-23
Setting Enable Privilege Options for a User Group, page 5-13
To add an NDG:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Under the Network Device Groups table, click Add Entry.
Tip
If the Network Device Groups table does not appear, choose Interface Configuration >
Advanced Options. Then, choose Network Device Groups.
Step 3
Step 4
In the Network Device Group Name box, type the name of the new NDG.
Tip
The maximum name length is 24 characters. Quotation marks (“) and commas (,) are not
allowed. Spaces are allowed.
In the Shared Secret box, enter a key for the Network Device Group. The maximum length is 32
characters.
Each device that is assigned to the Network Device Group will use the shared key that you enter here.
The key that was assigned to the device when it was added to the system is ignored. If the key entry is
simplifies key management for devices.
Step 5
In the RADIUS Key Wrap section, enter the shared secret keys for RADIUS Key Wrap in EAP-TLS
authentications.
Each key must be unique, and must also be distinct from the RADIUS shared key. These shared keys are
configurable for each AAA Client, as well as for each NDG. The NDG key configuration overrides the
AAA Client configuration. If the key entry is null, the AAA client key is used. See AAA Client
•
Key Encryption Key (KEK)—This is used for encryption of the Pairwise Master Key (PMK). In
ASCII mode, enter a key length of exactly 16 characters; in hexadecimal mode, enter a key length
of 32 characters.
•
Message Authentication Code Key (MACK)—This is used for the keyed hashed message
authentication code (HMAC) calculation over the RADIUS message. In ASCII mode, enter a key
length of exactly 20 characters; in hexadecimal mode, enter a key length of 40 characters.
Note
•
If you leave a key field empty when key wrap is enabled, the key will contain only zeros.
Key Input Format—Select whether to enter the keys as ASCII or hexadecimal strings (the default
is ASCII).
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 4
Chapter 3 Network Configuration
Configuring Network Device Groups
Note
You must enable the Key Wrap feature in the NAP Authentication Settings page to implement
these shared keys in EAP-TLS authentication.
Step 6
Step 7
Click Submit.
The Network Device Groups table displays the new NDG.
To populate the newly established NDG with AAA clients or AAA servers, perform one or more of the
following procedures, as applicable:
•
•
•
•
Assigning an Unassigned AAA Client or AAA Server to an NDG
You use this procedure to assign an unassigned AAA client or AAA server to an NDG. Before you begin
this procedure, you should have already configured the client or server and it should appear in the Not
Assigned AAA Clients or Not Assigned AAA Servers table.
To assign a network device to an NDG:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
In the Network Device Groups table, click Not Assigned.
Tip
If the Network Device Groups table does not appear, choose Interface Configuration >
Advanced Options. Then, check the Network Device Groups check box.
Step 3
Step 4
Click the name of the network device that you want to assign to an NDG.
From the Network Device Groups list, select the NDG to which you want to assign the AAA client or
AAA server.
Step 5
Click Submit.
The client or server is assigned to an NDG.
Reassigning AAA Clients or AAA Servers to an NDG
To reassign AAA clients or AAA servers to a new NDG:
Step 1
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 5
Chapter 3 Network Configuration
Configuring Network Device Groups
Step 2
Step 3
In the Network Device Groups table, click the name of the current group of the network device.
In the AAA Clients table or AAA Servers table, as applicable, click the name of the client or server that
you want to assign to a new NDG.
Step 4
Step 5
From the Network Device Group list, select the NDG to which you want to reassign the network device.
Click Submit.
The network device is assigned to the NDG you selected.
Editing a Network Device Group
You can rename an NDG, change the shared secret, and the key wrap configuration.
Caution
When renaming an NDG, ensure that there are no NARs or other shared profile components (SPCs) that
invoke the original NDG name. ACS performs no automatic checking to determine whether the original
NDG is still invoked. If a user’s authentication request incorporates an SPC that invokes a nonexistent
(or renamed) NDG, the attempt will fail and the user will be rejected.
To edit an NDG:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
In the Network Device Groups table, click the NDG that you want to edit.
Tip
If the Network Device Groups table does not appear, choose Interface Configuration >
Advanced Options. Then, check the Network Device Groups check box.
Step 3
Step 4
At the bottom of the page, click Edit Properties.
Change the network device group properties as required. For more information about these properties,
Step 5
Click Submit.
The NDG properties are changed.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 6
Chapter 3 Network Configuration
Configuring Proxy Distribution Tables
Deleting a Network Device Group
When you delete an NDG, all AAA clients and AAA servers that belong to the deleted group appear in
the Not Assigned AAA Clients or Not Assigned AAA Servers table.
Tip
It might be useful to empty an NDG of AAA clients and AAA servers before you delete it. You can do
this manually by performing the procedure Reassigning AAA Clients or AAA Servers to an NDG, page
3-25; or, in cases where you have a large number of devices to reassign, use the RDBMS Synchronization
feature.
Caution
When deleting an NDG, ensure that there are no NARs or other SPCs that invoke the original NDG. ACS
performs no automatic checking to determine whether the original NDG is still invoked. If a user
authentication request incorporates an SPC that invokes a nonexistent (or renamed) NDG, the attempt
will fail and the user will be rejected.
To delete an NDG:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
In the Network Device Groups table, click the NDG that you want to delete.
Tip
If the Network Device Groups table does not appear, choose Interface Configuration >
Advanced Options. Then check the Network Device Groups check box.
Step 3
Step 4
At the bottom of the page, click Delete Group.
A confirmation dialog box appears.
Click OK.
The NDG is deleted and its name is removed from the Network Device Groups table. Any AAA clients
and AAA servers that were in the NDG are now in the Not Assigned AAA Clients or Not Assigned AAA
Servers table.
Configuring Proxy Distribution Tables
This section describes the Proxy Distribution Table.
This section contains the following topics:
•
•
•
•
•
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 7
Chapter 3 Network Configuration
Configuring Proxy Distribution Tables
About the Proxy Distribution Table
If you enabled the Distributed Systems Settings, when you click Network Configuration, you will see
the Proxy Distribution Table.
Tip
To enable Distributed Systems Settings in the ACS, choose Interface Configuration > Advanced
Options. Then, check the Distributed System Settings check box.
The Proxy Distribution Table includes entries that show the character strings on which to proxy, the
AAA servers to proxy to, whether to strip the character string, and where to send the accounting
information (Local/Remote, Remote, or Local). For more information about the proxy feature, see Proxy
The entries that you define and place in the Proxy Distribution Table are treated one at a time for each
authentication request that ACS receives from the AAA client. The authentication request is defined in
the Proxy Distribution Table according to the forwarding destination. If a match to an entry in the Proxy
Distribution Table that contains proxy information is found, ACS forwards the request to the appropriate
AAA server.
The Character String column in the Proxy Distribution Table always contains an entry of (Default). The
(Default) entry matches authentication requests that are received by the local ACS that do not match any
other defined character strings. While you cannot change the character string definition for the (Default)
entry, you can change the distribution of authentication requests matching the (Default) entry. At
installation, the AAA server associated with the (Default) entry is the local ACS. You might sometimes
find it easier to define strings that match authentication requests to be processed locally rather than
defining strings that match authentication requests to be processed remotely. In such a case, associating
the (Default) entry with a remote AAA server permits you to configure your Proxy Distribution Table
with the more easily written entries.
Adding a New Proxy Distribution Table Entry
To create a Proxy Distribution Table entry:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Under the Proxy Distribution Table, click Add Entry.
Note
If the Proxy Distribution Table does not appear, choose Interface Configuration > Advanced
Options. Then, select the Distributed System Settings check box.
Step 3
Step 4
In the Character String box, type the string of characters, including the delimiter to forward on when
users dial in to be authenticated. For example, .uk.
Note
Angle brackets (<>) cannot be used.
From the Position list, select Prefix if the character string that you typed appears at the beginning of the
username or Suffix if the character string appears at the end of the username.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 8
Chapter 3 Network Configuration
Configuring Proxy Distribution Tables
Step 5
Step 6
From the Strip list, select Yes to strip the character string from the username that you entered, or select
No to leave it.
In the AAA Servers column, select the AAA server that you want to use for proxy. Click the --> (right
arrow button) to move it to the Forward To column.
Tip
Tip
You can also select additional AAA servers to use for backup proxy if the prior servers fail. To
set the order of AAA servers, in the Forward To column, click the name of the applicable server
and click Up or Down to move it into the position that you want.
If the AAA server that you want to use is not listed, choose Network Configuration > AAA
Servers. Then, choose Add Entry and complete the applicable information.
Step 7
From the Send Accounting Information list, select one of the following areas to which to report
accounting information:
•
•
•
Local—Keep accounting packets on the local ACS.
Remote—Send accounting packets to the remote ACS.
Local/Remote—Keep accounting packets on the local ACS and send them to the remote ACS.
Tip
This information is especially important if you are using the Max Sessions feature to control the
number of connections that a user is allowed. Max Sessions depends on accounting start and stop
records, and where the accounting information is sent determines where the Max Sessions
counter is tracked. The Failed Attempts log and the Logged in Users report are also affected by
example.
Step 8
When you finish, click Submit or Submit + Apply.
Sorting the Character String Match Order of Distribution Entries
You can use this procedure to set the priority by which ACS searches character string entries in the Proxy
Distribution Table when users dial in.
To determine the order by which ACS searches entries in the Proxy Distribution Table:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
Below the Proxy Distribution Table, click Sort Entries.
Tip
Before you sort the entries, you must configure at least two unique Proxy Distribution Table
entries in addition to the (Default) table entry.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -2 9
Chapter 3 Network Configuration
Configuring Proxy Distribution Tables
Step 3
Step 4
Select the character string entry to reorder, and then click Up or Down to move its position to reflect the
search order that you want.
When you finish sorting, click Submit or Submit + Apply.
Editing a Proxy Distribution Table Entry
To edit a Proxy Distribution Table entry:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
In the Character String column of the Proxy Distribution Table, click the distribution entry that you want
to edit.
The Edit Proxy Distribution Entry page appears.
Edit the entry as necessary.
Step 3
Step 4
Tip
For information about the parameters that make up a distribution entry, see Adding a New Proxy
When you finish editing the entry, click Submit or Submit + Apply.
Deleting a Proxy Distribution Table Entry
To delete a Proxy Distribution Table entry:
Step 1
Step 2
In the navigation bar, click Network Configuration.
The Network Configuration page opens.
In the Character String column of the Proxy Distribution Table, click the distribution entry that you want
to delete.
The Edit Proxy Distribution Entry page appears.
Click Delete.
Step 3
Step 4
A confirmation dialog box appears.
Click OK.
The distribution entry is deleted from the Proxy Distribution Table.
User Guide for Cisco Secure Access Control Server
OL-9971-01
3 -3 0
|