Hawking Technology Security Camera HNC210 User Manual

 
Congratulations on the purchase of your new Hawking Net-  
VisionTM HNC210 Wired 10/100Mbps Network Camera. The  
HNC210 is a high performance standalone camera system that  
provides an ideal solution for remote monitoring, surveillance, or  
sending live video over the Internet. The camera offers a broad  
array of applications and can be used to monitor various critical  
locations such as homes, offices, and other industrial and public  
areas. Please read this quick installation guide carefully before  
beginning your installation.  
General Installation:  
3
 
4
 
Front Panel  
Lens & Manual  
Focus Ring  
LED:  
Link/Activity  
LED:  
Ready  
LEDs  
-
Link/Activity: Green when monitoring; flashing for video  
transmission/reception  
-
Ready: Orange when device is powered on & ready for  
access  
5
 
Bottom Panel  
Reset  
Button  
Power  
Input  
LAN  
Port  
6
 
1
Locate the network  
cable connector (RJ-45  
port) on the camera’s  
bottom panel. Connect an  
Ethernet cable to the port.  
Connect the other end of  
the cable to the network.  
1
7
 
2 Locate the power input  
connector on the camera’s  
bottom panel, and attach  
the  
external  
power  
supply. Then, plug the  
adapter into an available  
outlet. Please check to see  
that the orange “Ready”  
LED located next to the  
lens of the camera is lit to  
ensure that the camera is  
powered on. (To ensure  
that there is a network  
connection, please check  
to see that the green  
“Link/Activity” LED is lit  
or flashing.)  
2
8
 
1 Insert the Hawking Net-VisionTM HNC210 Installation &  
Utilities CD into your CD-ROM Drive. When the main page  
loads, click on Quick Setup Wizard.  
1
9
 
2
2 The Setup Wizard will search for similar cameras available on  
your local area network. A “similar” camera will have the same  
code of four letters at the beginning of its serial number. This  
code is “HEMT” and can be found on either the right or left  
panel of the box, or on the label on the bottom of the camera.  
10  
 
Each available camera will be displayed in the camera list  
with its MAC address, current default IP address, and model  
number. (NOTE: The Setup Wizard may display an IP  
address for the camera that is already consistent with your  
network [LAN] settings, rather than the default one.) In the  
camera list, click on the camera you would like to configure so  
that it is highlighted blue, and then click Next. (If you are  
unsure about which camera you would like to configure, you  
can compare its MAC address displayed in the camera list to  
the one printed on the label on the underside of the camera.)  
NOTE: If the camera list does not display any available  
cameras, you should:  
a. Click on the “Rescan Camera” button, and  
b. Make sure that all available similar network cameras are  
connected properly to the network.  
If neither option above is successful, you can also perform a  
factory default reset by holding down the “Reset” button on  
the back panel of the camera for at least five seconds. Then,  
allow about 45 seconds to one minute for the camera to  
complete the reboot process. This should easily resolve the  
issue.  
11  
 
3 Next, the login username and password screen will appear.  
Please type in the default login and password and then press  
OK”. The default values are:  
Login: admin  
Password: 1234  
If you have already set a username and password, enter them  
and press “OK”.  
3
12  
 
4 The Setup Wizard will try to determine your network  
settings. If a DHCP server is present on your network, the  
Wizard will obtain your network settings and automatically  
configure your network camera to operate on your LAN by  
returning network settings that are consistent with your  
network.  
If no DHCP server is present, the Wizard will poll your PC’s  
internal network settings and suggest an appropriate static IP  
address in the “Manual IP” section to assign to the network  
camera. If you do not wish to use the suggested IP address,  
you may change your IP settings in the “Manual IP” section  
only.  
NOTE: Typically, your Gateway address is the IP address of  
your network’s router or Internet gateway. The Wizard will  
try and automatically fill in this address for you based on your  
PC’s current settings.  
Please click Next once your computer has found the  
appropriate IP settings.  
NOTE: If you are unfamiliar with how to manually set an IP  
address, a detailed example is provided at the end of this section.  
13  
 
4
14  
 
5 To protect your camera from unauthorized access and use,  
you will need to change the Admin Password, which is  
“1234” by default. The password can have a maximum of  
four characters. Confirm the new password by typing it again  
identically in the “Reconfirm” field.  
Click Next once you have confirmed your new password.  
5
15  
 
6 The following status page will appear. It will display a  
summary of the changes you have made to the network  
camera’s settings. If all the settings are correct, click Next to  
continue.  
6
16  
 
7 The setup process has now been completed. Please briefly  
review the text on the page before clicking on Reboot. After  
clicking Reboot, the Setup Wizard will close. Please allow about  
45 seconds to one minute for the camera to reboot. After the  
camera has finished rebooting, you can type in its new IP address  
in your web browser to begin accessing the camera.  
11  
17  
 
Example on How to Set the IP Address Manually  
The example shown here illustrates how to manually set an IP  
address using the Windows XP operating system. However, the  
procedure is similar for all other versions of Windows.  
When setting an IP address, you must make sure that the address  
you specify has the same first three octets (or segments) as the  
other devices on your LAN. In the figures on the previous pages,  
the camera has the following IP address: 10.1.1.144. The address  
is comprised of four segments separated by periods. Each  
segment is called an “octet”. All devices on your LAN must have  
the same first three octets, in this case “10.1.1”. Therefore, all  
devices on your LAN must have IP addresses of the form  
“10.1.1.x”, where “x” is a number between 0 and 254. When  
setting the IP address for the network camera, it is recommended  
(but not required) that you choose a number towards the end of  
the range between 0 and 254, excluding 254 itself. (Occasionally,  
the number 254 is used as the final segment for the default IP  
address of other devices.) Selecting a number towards the end of  
the range (preferably between 200 and 250) will help avoid  
conflicts with IP addresses that are already being used by other  
devices on the LAN.  
To determine the common octets/segments for your LAN  
settings, follow the steps outlined in the next two pages.  
18  
 
a. Click on Start in the bottom left corner of your screen.  
Then click on My Network Places.  
a
19  
 
b. Click on View Network Connections.  
b
20  
 
c. In the Network Connections window, you should see an  
icon titled Local Area Connection (or something similar).  
You can access this icon in two ways: a. by clicking or double-  
clicking on it, or b. by right-clicking on it and then clicking on  
Status from the resulting menu.  
c
21  
 
d. A window with the title Local Area Connection Status  
(or something similar) will appear. (See the figure on the  
following page.) Click on the Support tab. Under the  
heading Address Type, you will find an IP Address line and  
a Default Gateway line. These two lines will have IP  
addresses with the first three octets in common.  
Use this  
information to set the IP address for your network camera.  
You will use these same three octets as the first three octets  
for the IP address of your network camera. The final octet  
will be a number between 0 and 254.  
22  
 
d
23  
 
You can access and view your network camera’s images via  
a web browser by typing “http://IPAddressofCamera” in  
the address bar.  
You can also use the included software application to view,  
record, and playback the network camera’s images.  
The example illustrated in the previous section “Step 4: Run  
the IP Setup Program” deals with setting up an IP address to  
view the network camera within your LAN. For an example  
of how to view your network camera outside of your existing  
LAN via the Internet, please refer to the section in the user’s  
manual titled “How to View Your Camera via the  
Internet”.  
If the image is blurry, this is most likely because the camera  
lens is out of focus. To focus the lens, gently rotate the lens  
in either direction until the desired level of focus is reached.  
Please Note: Do not aggressively turn or overturn the lens,  
as this could lead to an unscrewing or damaging of the lens.  
It is highly recommended that you install the network  
camera(s) before placing them in the desired physical  
location.  
24  
 

Graco Baby Swing PD162168A User Manual
Grizzly Lathe G0584 User Manual
Grizzly Sander G1183 G1276 User Manual
Grundig Car Satellite TV System 26 LXW 68 8600 DL User Manual
HANNspree Car Video System 19 HF199H User Manual
Harbor Freight Tools Water Pump 93819 User Manual
Havis Shields Automobile Accessories C VS 2400 CHGR 1 User Manual
HP Hewlett Packard All in One Printer 3070 B611 User Manual
HP Hewlett Packard Portable Speaker QF299AAABC User Manual
Impex Home Gym AX PWR7 User Manual