I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Heavy Duty Swivel Adapter
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
CMA351
Installation Instructions
CMA351
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
3
CMA351
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
3/32"
5/32"
(provided)
(provided)
PARTS
A (1)
B (1)
D (2)
10-24
F (1)
5/16-18 x 3/8"
C (2)
.315 x .507 x 090
E (1)
#8-32 x 1/2"
G (1)
10-24 x 1/4"
H (1)
3/32"
J (1)
5/32"
4
Installation Instructions
CMA351
5. Secure Swivel Adapter (A) to 1 ½" NPT pipe using one Set
Screw (F) and hex wrench. (See Figure 2)
Installation
IMPORTANT ! : The following installation procedure
assumes that a 1 ½" NPT pipe has been properly
installed to the ceiling.
1. Place one Nylon washer (C) over each stud on Swivel
Adapter (A). (See Figure 1)
2. Align slots in stop plate (B) with two threaded studs on
Swivel Adapter (A). (See Figure 1)
(F) X1
3. Secure Stop plate (B) to Swivel Adapter (A) using two lock
nuts (D). (See Figure 1)
4
NOTE: DO NOT fully tighten lock nuts at this time.
5
(B) X1
2
(A) X1
(C) X2
Figure 2
1
6. Rotate the bottom of Swivel Adapter (A) until middle set
screw in swivel adapter (A) makes contact with tab in stop
plate (B). (See Figure 3)
(A) X1
NOTE: This is considered the first stop position.
Tab
(Not Visible)
6
Lower Set
Screw
(D) X2
3
(B) X1
(A) X1
(A) X1
Tab
Lower Set
Screw
TOP VIEW
Figure 1
4. Thread Swivel Adapter (A) onto existing 1 ½" NPT pipe.
(See Figure 2)
Figure 3
5
CMA351
Installation Instructions
7. Thread one 1 1/2" NPT pipe into lower Swivel Adapter (A).
(See Figure 4)
8. Secure lower 1 1/2" NPT pipe to swivel adapter (A) using
one set screw (G). (See Figure 4)
(E) X1
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the CMA351 up to (and
including) the display/projector does not exceed 500 lbs
(226.8 kg).
The weight capacity of the CMA351 may be LIMITED to
the lowest weight capacity of any other component located
between the CMA351 and the supporting structure!
(B) X1
Second Stop Location
X1
Figure 5
6
11. Tighten two lock nuts (D). (See Figure 6)
X1
(D) X2
Figure 4
9. Rotate the bottom portion of the CMA-351 to the desired
location for the second stop (0 degrees to 330 degrees).
(See Figure 5)
10. Insert one Phillips pan head screw (E) in the nearest
threaded hole in stop plate (B). (See Figure 5)
Figure 6
6
Installation Instructions
CMA351
7
CMA351
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8803-000010 RevA
©2007 Chief Manufacturing
11/07
P
F
+86-755-8996 9226
+86-755-8996 9217
|