VERTICAL FLOAT SUMP PUMP
Model 95591 - .75 HP
Model 95592 - 1 HP
Model 95593 - 1.5 HP
SET UP And OPERATIng InSTRUCTIOnS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAnUAL.
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Cover revised 07l
ELECTRICAL SAFETY
1. grounded tools must be plugged into a gFCI (ground Fault Circuit Interrupt-
er) outlet, properly installed, and grounded in accordance with all codes and
ordinances. never remove the grounding prong or modify the plug in any
way. Do not use any adapter plugs. Check with a qualified electrician if you
are in doubt as to whether the outlet is properly grounded. If the tools should
electrically malfunction or break down, grounding provides a low resistance path to
carry electricity away from the user.
2. double insulated tools are equipped with a polarized plug (one blade is wider
than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlet. Do not change
the plug in any way. Double insulation
eliminates the need for the three wire
grounded power cord and grounded power supply system.
3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges,
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
4. do not abuse the Power Cord. never use the Power Cord to carry the Sump
Pump or pull the Plug from an outlet. Keep the Power Cord away from heat,
oil, sharp edges, or moving parts. Replace damaged Power Cords immedi-
ately. Damaged Power Cords increase the risk of electric shock.
PERSOnAL SAFETY
1. Stay alert. Watch what you are doing, and use common sense when operat-
ing this product. Do not use the Sump Pump while tired or under the influ-
ence of drugs, alcohol, or medication. A moment of inattention while operating
this product may result in serious personal injury.
2. dress properly. do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
3. Use safety equipment. Wear AnSI-approved safety impact goggles when
assembling this product. Non-skid safety shoes must be used for appropriate
conditions.
TOOL USE And CARE
1. disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the Sump Pump. Such pre-
ventive safety measures reduce the risk of starting the unit accidentally.
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 3
2. Store idle equipment out of reach of children and other untrained persons.
Electrically-powered products are dangerous in the hands of untrained users.
3. Check for misalignment or binding of moving parts, breakage of parts, and
any other condition that may affect this product’s operation. If damaged,
have the Sump Pump serviced before using. Many accidents are caused by
poorly maintained equipment.
SERVICE
1. Service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
2. When servicing this product, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SPECIFIC SAFETY RULES
1. Maintain labels and nameplates on the Pump. These carry important informa-
tion. If unreadable or missing, contact Harbor Freight Tools for a replacement.
2.
Wear AnSI-approved safety impact eye goggles when assembling
the Pump. Using personal safety devices reduce the risk for injury.
Safety impact eye goggles are available from Harbor Freight Tools.
3. Use the right product for the job. There are certain applications for which this
product was designed. Do not use small tools, attachments, or equipment to do
the work of larger industrial tools, attachments, or equipment.
4. Maintain a safe environment. Keep the area well lit. Make sure there is ad-
equate surrounding space. Always keep the area free of obstructions, grease, oil,
trash, and other debris. Do not use an electrically powered product in areas near
flammable chemicals, dusts, and vapors.
5.
Risk of electrical shock. Always disconnect the Pump from its power
source before handling or making any adjustments to the tool. Always
wear non-skid rubber boots when water is on the floor and you must
unplug the Pump. Make sure the electrical power source is a separate-
ly fused, grounded, 3-wire type gFCI (Ground Fault Circuit Interrupter) outlet. do
not remove the ground prong on the Power Cord Plug. do not use an exten-
sion cord.
6. do not pump hazardous materials. Do not pump explosive or flammable ma-
terials such as fuel, oil, kerosene, gasoline, etc. Do not pump in close proximity
to flammable or explosive materials. Do not pump fats, oils, salt or waste water.
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 4
This Pump is designed to move clean or dirty water only. Do not pump water
hotter than 95 degrees Fahrenheit.
7. Make sure the discharge pipe (not included) is secured to a solid surface to
ensure the stability of the Pump.
8. Make sure to position the Pump on a flat, level, solid surface.
9. Arrange a “drip loop” in the Power Cord connecting the Pump to a 115 volt,
gFCI electrical outlet. A drip loop is that part of the Power
Cord below the level of the outlet to prevent water from
drip Loop
traveling along the Power Cord and coming in contact with
OUTLET
the outlet. If the Power Plug or electrical outlet does get
wet, do not unplug the Power Cord. Disconnect the fuse or
circuit breaker that supplies power to the Pump. Then,
dEVICE
unplug the Power Cord and examine for presence of water
in the outlet. (See drip Loop, right.)
CORd
10. If necessary, have a certified electrician install (within 10 feet of where the
Pump will be located) a 115 volt, gFCI electrical outlet that is dedicated only
to the Pump. Any outlet should be above the water line.
11. nEVER raise or lower the Pump by its electrical Power Cord.
12. In cold weather, when the Pump is not in use, protect the interior of the Pump
from freezing by draining the water and pumping a permanent type automo-
bile anti-freeze containing a rust inhibitor through the system. A 50% mixture
with water is recommended. Be sure to flush the system with a neutralizing liquid
prior to re-use of the Pump.
13. If an extension cord is used (for temporary use only) connections must not
come in contact with water or any wet surfaces.
14. Prior to use, and periodically thereafter, check to make sure all connections
are tight and secure.
15. Industrial applications must follow OSHA requirements.
16. Performance of this product may vary depending on variations in local line
voltage.
17. People with pacemakers should consult their physician(s) before use. Elec-
tromagnetic fields in close proximity to heart pacemaker could cause pace-
maker interference or pacemaker failure.
18. The warnings and cautions discussed in this manual cannot cover all pos-
sible conditions and situations that may occur. It must be understood by the
operator that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 5
of electric shock. (See 3-Prong Plug
and Outlet.)
gROUndIng
TO PREVEnT
ELECTRIC
WARnIng
2. The grounding prong in the plug is
connected through the green wire in-
side the cord to the grounding system
in the tool. The green wire in the cord
must be the only wire connected to
the tool’s grounding system and must
never be attached to an electrically
“live” terminal. (See 3-Prong Plug
and Outlet.)
SHOCK And dEATH FROM
InCORRECT gROUndIng
WIRE COnnECTIOn:
Check with a qualified
electrician if you are in doubt
as to whether the outlet is
properly grounded. do not
modify the power cord plug
provided with the tool. never
remove the grounding prong
from the plug. do not use the
tool if the power cord or plug
is damaged. If damaged, have
it repaired by a service facility
before use. If the plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
3. The tool must be plugged into an
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-Prong
Plug and Outlet.)
double Insulated Tools: Tools
with Two Prong Plugs
grounded Tools: Tools with Three
Prong Plugs
Outlets for 2-Prong Plug
1. Tools marked “Double Insulated” do
not require grounding. They have
a special double insulation system
which satisfies OSHA requirements
and complies with the applicable
standards of Underwriters Labora-
tories, Inc., the Canadian Standard
Association, and the National Electri-
cal Code. (See Outlets for 2-Prong
Plug.)
3-Prong Plug and Outlet
1. Tools marked with “Grounding Re-
quired” have a three wire cord and
three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the tool should
electrically malfunction or break
down, grounding provides a low
resistance path to carry electricity
away from the user, reducing the risk
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 6
2. Double insulated tools may be used
in either of the 120 volt outlets shown
in the preceding illustration. (See
Outlets for 2-Prong Plug.)
dition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
Extension Cords
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
RECOMMEndEd MInIMUM WIRE
gAUgE FOR EXTEnSIOn CORdS*
(120/240 VOLT)
EXTEnSIOn CORd
nAMEPLATE
LEngTH
2. As the distance from the supply outlet
increases, you must use a heavier
gauge extension cord. Using exten-
sion cords with inadequately sized
wire causes a serious drop in voltage,
resulting in loss of power and pos-
sible tool damage.
AMPERES
(at full load)
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
(See Table A.)
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See Table A.)
-
-
* Based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
TABLE A
Symbology
4. When using more than one exten-
sion cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See Table A.)
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
5. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See Table A.)
V~
A
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
No Load Revolutions per Minute
(RPM)
n xxxx/min.
0
7. Make sure the extension cord is prop-
erly wired and in good electrical con-
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 7
UnPACKIng
When unpacking, check to make sure all the parts shown on the Parts List on
page 12 are included. If any parts are missing or broken, please call Harbor Freight
Tools at the number shown on the cover of this manual as soon as possible.
ASSEMBLY And OPERATIng InSTRUCTIOnS
note: For additional information regarding the parts listed in the following pages, refer
to the Assembly diagram on page 13.
WARnIng! Always make sure to turn off the electricity powering the
Pump’s electrical outlet and that the Pump is unplugged from its outlet prior to
assembling the unit, unclogging the unit, or making any adjustments to the unit.
1. If necessary, have a certified electrician install (within 10 feet of where the Pump
will be located) a 115 volt, GFCI electrical outlet that is dedicated only to the Pump.
Any outlet should be well above the water line.
2. The discharge has both internal and external NPT threads. Use either 1-3/4” NPT
Male or 1-1/2” NPT Female PVC pipe for the discharge line. Do not use a pipe
smaller than 1-1/2”.
REV 08b
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 8
CHECK VALVE
OR
FIgURE E
UnIOn
(nOT InCLUdEd)
TO 115 VOLT, gROUndEd
gFCI OUTLET
dISCHARgE PIPE
(nOT InCLUdEd)
1/8”
AIR BLEEd HOLE
o
BASE
(25)
3. Connect the Discharge Pipe to the Base (25). nOTE: Make sure the Discharge
Pipe is secured to a solid surface, with appropriate hardware (not included), to
ensure the stability of the Pump. (See Figure E.)
4. Install an additional union (not included) or other means of separating the Dis-
charge Pipe just above the floor to facilitate removal of the Pump if necessary.
(See Figure E.)
5. A check valve (not included) is recommended just above, or in place of, the union
to prevent the backflow of water after each pump cycle. If a Check Valve is used,
a 1/8” diameter air bleed hole should be drilled through the Discharge Pipe just
above the lower Base (25) to prevent Pump “airlock”. A small spray of water out of
this hole is normal while the Pump is running. (See Figure E.)
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 9
6. Carefully set the Pump in place. do not lower or raise the Pump by the Power
Cord or discharge Pipe. (See Figure E.)
7. The Float Switch (2) automatically switches on and off at a water depth of approxi-
mately 4 inches. The ON/OFF height can be manually changed by adjusting the
Float Switch Lock. CAUTIOn: Do not run the Pump dry. Doing so will increase
wear to the unit and possibly cause seal damage. (See Figure E.)
8. nOTE: This Pump has a built-in thermal protector for the Motor which automati-
cally shuts it off to avoid overheating. After the Motor cools, it will cycle back on.
Wait for the cycle to continue. Do not try to turn on the Pump manually after it has
automatically shut off.
9. Connect additional Discharge Pipe as needed to direct the water discharge to
the desired location. The discharge should be kept as short as possible with a
minimum number of turns. IMPORTAnT: Do not exceed the maximum lift of the
Pump:
Model 95591 = 20 Feet.
Model 95592 = 24 Feet.
Model 95593 = 26 Feet.
10. Connect the Power Cord & Plug to its 115 volt, GFCI electrical outlet, while making
sure to form a “drip loop” in the Power Cord. (See drip Loop, page 5.)
11. When the water level exceeds approximately 4 inches the Pump will automatically
turn on and run continuously until the water level falls below 4 inches at which time
the Pump will automatically turn off.
12.
WARnIng! When shutting off power to the Pump, always shut off the electrical
power to the GFCI outlet first. Then, disconnect the Pump’s Power Cord & Plug
from the GFCI outlet.
InSPECTIOn, MAInTEnAnCE, And CLEAnIng
WARnIng! Always shut off the electrical power to the GFCI outlet first. Then, dis-
connect the Pump’s Power Cord & Plug from the GFCI outlet prior to performing
any inspection, maintenance, or cleaning procedures.
1. Before each use, inspect the general condition of the Pump. Check for cracked
or broken parts, damaged electrical wiring, clogged Impeller Cover, Impeller, Dis-
charge Pipes, and any other condition that may affect safe operation. If abnormal
noise or vibration occurs, have the problem corrected before further use.
do not use damaged equipment.
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 10
2. To clean the Impeller Cover and Impeller: A clogged or dirty Impeller Cover
or Impeller (28) will greatly reduce performance of the Pump. To clean the Impel-
ler Cover (31), spray the Cover with clean water. To clean the Impeller, remove
the nine Screws (32) at the bottom of the Base (25). Then, remove the Base to
expose the Impeller Cover and Impeller. Use a stream of clean water to clean the
Impeller and Impeller area inside the Pump. Then, replace the Base. (See Assy.
diagram.)
3. When finished, store the Pump in a clean, dry and safe location out of reach of
children. In cold weather, when the Pump is not in use, protect the interior of the
Pump from freezing by draining the water and pumping a permanent type automo-
bile anti-freeze containing a rust inhibitor through the system. A 50% mixture with
water is recommended. Be sure to flush the system with a neutralizing liquid prior
to re-use of the Pump. note: Always properly dispose of all used anti-freeze.
CAUTIOn! All maintenance, service, or repairs not mentioned in this manual
must only be performed by a qualified service technician.
TROUBLESHOOTIng
Problem
Pump does not start.
Possible Solution
1. Make sure the Pump is plugged into a working, 115 volt, GFCI
electrical outlet.
2. Adjust the Float Switch to a lower position.
1. Clean Impeller and Impeller Cover.
No flow from the Pump.
2. Check Discharge Pipe for freezing or blockage. If necessary, thaw
Pipe and/or remove excess debris.
3. Discharge Pipe excessively bent. Straighten Pipe.
Pump does not automatically 1. Float Switch cannot sink down. Lower Float Switch.
switch off.
2. Check for excessive debris beneath Float Switch.
3. Unplug Pump from its electrical outlet. Discontinue using Pump until
a qualified service technician checks Pump for damage.
Insufficient flow.
1. Clean Impeller and Impeller Cover.
2. Check Discharge Pipe for freezing or blockage. If necessary, thaw
Pipe and/or remove excess debris. Be careful of excessive lift height.
3. Have a qualified service technician clean interior of Pump and, if
necessary, replace worn parts.
Pump switches off too soon.
1. Clean Impeller and Impeller Cover.
2. Make sure the water temperature does not exceed 95° Fahrenheit.
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 11
PLEASE REAd THE FOLLOWIng CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL
ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY
REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE
MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS
AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL
RISKS AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS THERETO.
PARTS LIST
Part
1
2
3
4
5
6
7
8
description
Qty.
1
1
5
1
1
1
1
1
1
1
1
2
1
1
1
1
Part
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
description
Qty.
1
1
1
1
1
1
1
3
1
4
1
1
1
1
1
9
Screw
Washer
Float Switch/Float Switch Lock
Screw
Back Cover
Stator
Screw
Bearing
Rotor
Back Shell
Capacitor
Cable Guide
Switch
Cable Compaction Buckle
Waterproof
Bearing
Main Body
Oil Seal
Base
9
10
11
12
13
14
15
16
Screw
Cable Compaction Board
Screw
Washer
Impeller
Nut
O-Ring
Screw
O-Ring
Impeller Cover
Screw
Spring Washer
Ground Wire
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 12
ASSEMBLY dIAgRAM
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 13
LIMITEd 90 dAY WARRAnTY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESS-
LY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 95591/95592/95593
For technical questions, please call 1-800-444-3353
PAGE 14
|